Adsorption Isotherms and Surface Area
CSIR NET chemistry: physisorption vs chemisorption, Langmuir, Freundlich, Temkin and BET isotherms, isosteric heat, Gibbs adsorption, Kelvin equation, BET area.
- 22 min
On this page · 19 sections
- Prerequisites
- The Hook: A Football Field in a Teaspoon
- 1. Vocabulary
- 2. Physisorption and Chemisorption
- 3. The Langmuir Isotherm
- 4. Isosteric Enthalpy of Adsorption
- 5. Freundlich and Temkin Isotherms
- 6. Multilayers: the BET Isotherm
- 7. The Six Types of Physisorption Isotherm
- 8. Surface Tension and Curved Surfaces
- 9. The Gibbs Adsorption Isotherm
- 10. Rate of Adsorption
- Memory Tricks
- Don’t Confuse
- Common Mistakes
- Practice
- Quick Revision Table
- Key Takeaways
- What’s Next
Prerequisites
- Kinetic Theory of Gases: the flux of molecules striking a surface, \( Z_W = P/\sqrt{2\pi mk_BT} \), sets the rate of adsorption.
- Chemical Equilibrium and Le Chatelier’s Principle: Langmuir’s K is an equilibrium constant, with a van ’t Hoff temperature dependence.
- Colloids: Classification, Micelles, Kinetic and Optical Properties: surfactants, CMC and surface tension.
- Straight-line fitting and reading slopes and intercepts: Graphs of Functions and Scientific Plots.
The Hook: A Football Field in a Teaspoon
1. Vocabulary
- Adsorption: accumulation of a substance at an interface. Absorption: uniform penetration into the bulk. Sorption covers both.
- Adsorbate: the substance adsorbed. Adsorbent (substrate): the surface.
- Fractional coverage \( \theta = \) (sites occupied)/(sites available) \( = V/V_m \), where \( V_m \) is the volume adsorbed at monolayer coverage.
- Isotherm: amount adsorbed against pressure (or concentration) at constant T. Isobar: against T at constant P. Isostere: P against T at constant amount.
Why adsorption is exothermic
Spontaneous adsorption has \( \Delta G < 0 \). A gas molecule that adsorbs loses translational freedom, so \( \Delta S < 0 \). Then \( \Delta H = \Delta G + T\Delta S < 0 \): adsorption is almost always exothermic, and by Le Chatelier’s principle the amount adsorbed at equilibrium falls as temperature rises.
2. Physisorption and Chemisorption
| Feature | Physisorption | Chemisorption |
|---|---|---|
| Forces | Van der Waals (dispersion, dipole) | Chemical bond (covalent or ionic) |
| Enthalpy of adsorption | Small, of the order of 20 kJ mol⁻¹, comparable to the enthalpy of condensation | Large, of the order of 100–400 kJ mol⁻¹, comparable to bond enthalpies |
| Specificity | Non-specific; any gas on any surface | Highly specific (H₂ on Ni, Pt, Pd; not on Al₂O₃) |
| Layers | Multilayer possible | Monolayer only |
| Activation energy | Negligible; fast | Often activated; can be slow |
| Temperature range | Significant only near or below the adsorbate’s boiling point | Can occur at high temperatures |
| Reversibility | Reversible by lowering P or raising T | Often irreversible; may dissociate the adsorbate (H₂ → 2H) |
| Dependence on the gas | Increases with ease of liquefaction (higher critical temperature) | Depends on chemical affinity |
| Use | Surface area and pore size measurement | Catalysis; metal dispersion measurement |
Ease of liquefaction rule (physisorption): gases with higher critical temperatures adsorb more on charcoal: SO₂ and NH₃ much more than CH₄, which adsorbs more than H₂.
Isobars
- Physisorption isobar: amount adsorbed falls steadily with temperature.
- Chemisorption isobar: amount may rise first with temperature (the activation barrier is overcome) and then fall (exothermic equilibrium). A single isobar often shows physisorption at low T, a dip, then a chemisorption hump.
Residence time
A molecule held by an adsorption energy \( E_d \) stays on the surface for a mean time
$$\tau = \tau_0 \, e^{E_d/RT}$$where \( \tau_0 \) is of the order of a vibrational period (about \( 10^{-13} \) s). At 298 K, \( E_d = 25 \) kJ mol⁻¹ gives \( \tau \approx 2\times10^{-9} \) s; \( E_d = 100 \) kJ mol⁻¹ gives about \( 3\times10^{4} \) s (roughly nine hours). Physisorbed molecules come and go in nanoseconds; chemisorbed ones can stay for hours.
3. The Langmuir Isotherm
Assumptions
- Adsorption stops at a monolayer.
- All sites are equivalent, and the surface is uniform.
- Adsorption at a site is independent of neighbouring occupancy (no lateral interactions), so the enthalpy of adsorption does not depend on θ.
- A dynamic equilibrium exists between adsorption and desorption.
Derivation (kinetic)
For \( \text{A(g)} + \text{S} \rightleftharpoons \text{A–S} \) with N sites:
- Rate of adsorption \( = k_a P N(1-\theta) \) (proportional to pressure and to empty sites)
- Rate of desorption \( = k_d N\theta \)
At equilibrium, with \( K = k_a/k_d \):
$$\boxed{\theta = \frac{KP}{1 + KP}}$$Limits:
- Low P (\( KP \ll 1 \)): \( \theta \approx KP \), linear (Henry’s law region).
- High P (\( KP \gg 1 \)): \( \theta \to 1 \), saturation. More precisely \( 1-\theta \approx 1/KP \).
- Half coverage at \( P = 1/K \).
Linear form (with \( \theta = V/V_m \)):
$$\frac{P}{V} = \frac{1}{KV_m} + \frac{P}{V_m}$$A plot of P/V against P gives slope \( 1/V_m \) and intercept \( 1/(KV_m) \). The other common linearisation is \( 1/V = 1/V_m + 1/(KV_mP) \).
Variants
Dissociative adsorption (\( \text{A}_2 + 2\text{S} \rightleftharpoons 2\text{A–S} \)), for example H₂ on metals: adsorption needs two empty sites, desorption two adjacent occupied ones, so \( k_aP(1-\theta)^2 = k_d\theta^2 \):
$$\theta = \frac{(KP)^{1/2}}{1 + (KP)^{1/2}}$$At low pressure \( \theta \propto P^{1/2} \). A slope of 1/2 in log θ against log P at low pressure is the signature of dissociation.
Competitive adsorption of A and B on the same sites:
$$\theta_A = \frac{K_AP_A}{1 + K_AP_A + K_BP_B}, \qquad \theta_B = \frac{K_BP_B}{1 + K_AP_A + K_BP_B}$$A strongly adsorbed second gas (large \( K_BP_B \)) suppresses \( \theta_A \): this is the basis of catalyst poisoning and product inhibition in heterogeneous catalysis.
Adsorption from solution: replace P by concentration: \( q = q_m Kc/(1 + Kc) \). Acetic acid on charcoal is the classic laboratory isotherm.
Temperature dependence of K
K behaves like an equilibrium constant: \( K = K_0\, e^{-\Delta H_{\text{ads}}/RT} \). Since \( \Delta H_{\text{ads}} < 0 \), K falls as T rises, and a higher pressure is needed for the same coverage.
4. Isosteric Enthalpy of Adsorption
At constant coverage θ, \( KP \) is constant (Langmuir) and more generally the Clausius–Clapeyron analogue holds:
$$\left(\frac{\partial \ln P}{\partial (1/T)}\right)_\theta = \frac{\Delta H_{\text{ads}}}{R}$$From two isotherms, read the pressures \( P_1 \) at \( T_1 \) and \( P_2 \) at \( T_2 \) that give the same amount adsorbed:
$$\ln\frac{P_2}{P_1} = \frac{\Delta H_{\text{ads}}}{R}\left(\frac{1}{T_2} - \frac{1}{T_1}\right)$$The magnitude is the isosteric heat of adsorption, \( q_{st} = -\Delta H_{\text{ads}} \). If it falls with coverage, the surface is heterogeneous or adsorbed molecules repel one another, and the Langmuir model fails.
5. Freundlich and Temkin Isotherms
Real surfaces are heterogeneous: the most strongly binding sites fill first, so the heat of adsorption falls with coverage.
Freundlich (empirical):
$$\frac{x}{m} = kP^{1/n} \quad (n > 1), \qquad \log\frac{x}{m} = \log k + \frac{1}{n}\log P$$where x is the mass adsorbed on mass m of adsorbent. A log–log plot gives slope 1/n (between 0 and 1) and intercept log k. It corresponds to a heat of adsorption that falls logarithmically with coverage. It has no saturation limit and fails at high pressure, but often fits intermediate pressures and adsorption from solution well (\( x/m = kc^{1/n} \)).
Temkin: assumes the heat of adsorption falls linearly with coverage:
$$\theta = c_1 \ln(c_2 P)$$It fits chemisorption at intermediate coverage, for example N₂ on iron in ammonia-synthesis studies.
| Isotherm | Heat of adsorption vs θ | Limiting behaviour |
|---|---|---|
| Langmuir | Constant | Linear at low P, saturates at high P |
| Freundlich | Falls logarithmically | No saturation; \( x/m \propto P^{1/n} \) |
| Temkin | Falls linearly | θ linear in ln P |
| BET | First layer different, higher layers = condensation | Multilayer; diverges as \( P \to P_0 \) |
6. Multilayers: the BET Isotherm
Brunauer, Emmett and Teller extended Langmuir’s picture to many layers.
Assumptions: the first layer adsorbs on uniform sites with enthalpy \( \Delta H_1 \); each later layer adsorbs on the one below with the enthalpy of liquefaction (condensation); no lateral interactions; the number of layers becomes infinite at the saturation vapour pressure \( P_0 \).
With relative pressure \( x = P/P_0 \):
$$\frac{V}{V_m} = \frac{cx}{(1-x)(1 - x + cx)}$$and the linear form used in practice:
$$\boxed{\frac{x}{V(1-x)} = \frac{1}{V_mc} + \frac{(c-1)}{V_mc}\,x}$$From slope s and intercept i: \( V_m = 1/(s + i) \) and \( c = 1 + s/i \).
- The constant c is roughly \( \exp[(\Delta H_{\text{des},1} - \Delta H_{\text{vap}})/RT] \): large c means the first layer binds much more strongly than later layers.
- Range of validity: the linear BET plot normally holds for \( P/P_0 \) of about 0.05–0.30. Below, surface heterogeneity dominates; above, capillary condensation and the assumption of infinite layers fail.
- Single-point method: for large c, \( V_m \approx V(1 - x) \) from one measurement.
From \( V_m \) to surface area
$$S = \frac{V_m}{V_{\text{mol}}}\, N_A\, \sigma$$where \( V_{\text{mol}} = 22\,414\ \text{cm}^3\ \text{mol}^{-1} \) at STP and σ is the cross-sectional area of one adsorbate molecule. For N₂ at 77 K the standard value is \( \sigma = 0.162\ \text{nm}^2 \), so
$$S\ (\text{m}^2\ \text{g}^{-1}) = 4.35 \times V_m\ (\text{cm}^3\ \text{STP g}^{-1})$$Krypton is used for very small areas because its low saturation pressure at 77 K makes small uptakes easier to measure.
7. The Six Types of Physisorption Isotherm
The IUPAC classification groups experimental physisorption isotherms into six shapes. (A 2015 IUPAC report subdivides some of them; the six-type scheme is what questions use.)
| Type | Shape | Interpretation |
|---|---|---|
| I | Rises steeply and saturates (Langmuir-like) | Microporous solids (activated carbon, zeolites): pores fill at low P/P₀. Chemisorption also gives this shape. |
| II | Concave, then a “knee” (point B), then steady rise | Non-porous or macroporous; unrestricted multilayer; strong first layer (large BET c) |
| III | Convex throughout, no knee | Non-porous, weak adsorbent–adsorbate interaction (BET c < 2) |
| IV | Like II at low P, then a plateau, with a hysteresis loop | Mesoporous; capillary condensation in pores |
| V | Like III at low P, then pore filling with hysteresis | Mesoporous, weak interaction |
| VI | Stepwise | Layer-by-layer adsorption on a very uniform non-porous surface |
Point B (the knee in type II and IV) marks completion of the monolayer; the uptake there is close to \( V_m \).
Pore-size classes (IUPAC): micropores below 2 nm, mesopores 2–50 nm, macropores above 50 nm.
graph TD
A["Shape of the N2 isotherm at 77 K"] --> B{"Saturates at low P/P0?"}
B -->|Yes| C["Type I: micropores"]
B -->|No| D{"Knee at low P/P0?"}
D -->|Yes| E{"Hysteresis loop?"}
D -->|No| F{"Hysteresis loop?"}
E -->|No| G["Type II: non-porous,
strong first layer"]
E -->|Yes| H["Type IV: mesoporous"]
F -->|No| I["Type III: weak interaction"]
F -->|Yes| J["Type V: mesoporous,
weak interaction"]8. Surface Tension and Curved Surfaces
The surface tension γ is the reversible work to create unit area of surface at constant T, P and composition: \( \gamma = (\partial G/\partial A)_{T,P,n} \). Units N m⁻¹ = J m⁻². Water at 25 °C has γ ≈ 72 mN m⁻¹. γ falls with temperature and vanishes at the critical point.
Young–Laplace equation: the pressure inside a spherical droplet or bubble of radius r exceeds the outside by
$$\Delta P = \frac{2\gamma}{r}$$(a soap bubble, with two surfaces, has \( 4\gamma/r \)).
Capillary rise: \( h = \dfrac{2\gamma\cos\theta_c}{\rho g r} \), where \( \theta_c \) is the contact angle. Liquids that wet the wall (\( \theta_c < 90^\circ \)) rise; mercury on glass (\( \theta_c > 90^\circ \)) is depressed.
Young’s equation for a drop on a solid: \( \gamma_{SV} = \gamma_{SL} + \gamma_{LV}\cos\theta_c \).
Kelvin equation: the vapour pressure P over a convex droplet of radius r exceeds that over a flat surface \( P_0 \):
$$\ln\frac{P}{P_0} = \frac{2\gamma V_m}{rRT}$$with \( V_m \) the molar volume of the liquid. For a concave meniscus in a pore wetted by the liquid the sign is reversed, so vapour condenses in narrow pores below \( P_0 \). This capillary condensation causes the type IV hysteresis loop, and inverting the Kelvin equation over the desorption branch gives the mesopore size distribution (the BJH method). The same effect explains Ostwald ripening (small particles dissolve, large ones grow), supersaturation needed for droplet nucleation, and the higher solubility of small crystals.
9. The Gibbs Adsorption Isotherm
At a liquid surface, a solute may be enriched or depleted relative to the bulk. Gibbs defined the surface excess \( \Gamma_2 \) (mol m⁻²) of the solute relative to the solvent and related it to the change of surface tension with solute activity. For a dilute, ideal solution of a non-ionic solute:
$$\boxed{\Gamma_2 = -\frac{1}{RT}\frac{d\gamma}{d\ln c} = -\frac{c}{RT}\frac{d\gamma}{dc}}$$- Surface-active solutes (alcohols, fatty acids, surfactants) lower γ: \( d\gamma/dc < 0 \), so \( \Gamma_2 > 0 \) (positive adsorption).
- Surface-inactive solutes (strong inorganic electrolytes such as NaCl) raise γ slightly: \( \Gamma_2 < 0 \); the surface is depleted.
- For a 1:1 ionic surfactant without added salt, both ions adsorb together and the factor becomes \( 1/(2RT) \). With a large excess of salt it returns to \( 1/RT \).
- Just below the CMC, γ falls linearly with ln c; the constant slope gives the saturated surface excess \( \Gamma_\infty \), and \( 1/(N_A\Gamma_\infty) \) is the area per molecule at the surface.
Surface pressure \( \Pi = \gamma_0 - \gamma \). For a dilute, gaseous monolayer \( \Pi A = k_BT \) per molecule, a two-dimensional ideal gas law (measured on a Langmuir trough for insoluble films). The Szyszkowski equation \( \gamma_0 - \gamma = RT\Gamma_\infty\ln(1 + Kc) \) is what you get by combining the Gibbs equation with a Langmuir isotherm for the surface excess.
10. Rate of Adsorption
The number of gas molecules striking unit area per second (kinetic theory) is
$$Z_W = \frac{P}{\sqrt{2\pi m k_BT}}$$The rate of adsorption is \( sZ_W \), where the sticking probability s (0 to 1) falls as coverage rises and, for activated chemisorption, contains a Boltzmann factor. For N₂ at 298 K and \( 1.33\times10^{-4} \) Pa (10⁻⁶ Torr), \( Z_W \approx 3.8\times10^{18}\ \text{m}^{-2}\ \text{s}^{-1} \); with of the order of \( 10^{19} \) sites per m², a surface is covered in a few seconds if s = 1. That is why surface-science experiments need ultra-high vacuum.
Memory Tricks
Don’t Confuse
| This | vs | That |
|---|---|---|
| Adsorption: at the surface | Absorption: throughout the bulk | |
| Physisorption: weak, multilayer, non-specific | Chemisorption: strong, monolayer, specific, may be activated | |
| Langmuir: constant heat, monolayer | Freundlich: heat falls logarithmically, no saturation | |
| Temkin: heat falls linearly | BET: first layer distinct, later layers = condensation | |
| \( V_m \) from Langmuir slope \( 1/V_m \) | \( V_m \) from BET as \( 1/(s+i) \) | |
| Type II: non-porous, no hysteresis | Type IV: mesoporous, hysteresis loop | |
| Kelvin, convex drop: P > P₀ | Kelvin, concave meniscus in a pore: condensation below P₀ | |
| Gibbs: Γ from γ against ln c | Langmuir: θ from P (or c) | |
| Isosteric heat: from P at constant θ, two temperatures | Integral heat: total heat for a given uptake (calorimetry) |
Common Mistakes
Practice
All questions below are original practice questions written for this page. They are not from any CSIR NET paper.
Level 1: Foundation
- State two assumptions of the Langmuir isotherm that BET relaxes or changes.
- What is the order of a Langmuir isotherm with respect to pressure at very low and at very high pressure?
- Classify mesopores by size.
Answers
- Langmuir allows only a monolayer; BET allows unlimited multilayers. Langmuir has one adsorption enthalpy; BET uses one value for the first layer and the enthalpy of condensation for all later layers.
- First order (θ ≈ KP) at low pressure; zero order (θ → 1) at high pressure.
- Pore widths between 2 nm and 50 nm.
Level 2: Part B Style
Practice Q1. Hydrogen adsorbs dissociatively on a metal and follows the Langmuir model. At low pressures the coverage is proportional to:
(a) P (b) P² (c) \( P^{1/2} \) (d) independent of P
Answer: (c)
\( \theta = (KP)^{1/2}/[1 + (KP)^{1/2}] \approx (KP)^{1/2} \) when \( (KP)^{1/2} \ll 1 \). The half-power arises because two empty sites are needed for each H₂ that adsorbs.
Practice Q2. Freundlich adsorption of a dye from solution on charcoal gives a straight line of log(x/m) against log c with slope 0.50 and intercept 0.30 (x/m in mg g⁻¹, c in mg L⁻¹). The value of x/m at c = 16 mg L⁻¹ is closest to:
(a) 2.0 mg g⁻¹ (b) 4.0 mg g⁻¹ (c) 8.0 mg g⁻¹ (d) 32 mg g⁻¹
Answer: (c) 8.0 mg g⁻¹
\( k = 10^{0.30} = 2.0 \), \( 1/n = 0.50 \). \( x/m = 2.0 \times 16^{0.5} = 2.0 \times 4 = 8.0\ \text{mg g}^{-1} \). Option (d) forgets the square root (2.0 × 16).
Practice Q3. A nitrogen isotherm at 77 K rises like a type II isotherm at low P/P₀ but shows a plateau near saturation and a hysteresis loop between adsorption and desorption. The solid is best described as:
(a) microporous (b) mesoporous (c) non-porous with weak gas–solid interaction (d) a uniform surface adsorbing layer by layer
Answer: (b) mesoporous
This is a type IV isotherm. The hysteresis arises from capillary condensation in mesopores, where condensation and evaporation occur at different relative pressures. Microporous solids give type I; weak interaction gives type III or V; stepwise uptake is type VI.
Practice Q4. Gases A and B adsorb competitively on the same sites, with \( K_A = 0.50\ \text{kPa}^{-1} \) and \( K_B = 2.0\ \text{kPa}^{-1} \). At \( P_A = 4.0 \) kPa and \( P_B = 1.0 \) kPa, the fraction of sites left empty is:
(a) 0.20 (b) 0.33 (c) 0.40 (d) 0.60
Answer: (a) 0.20
Denominator \( 1 + K_AP_A + K_BP_B = 1 + 2.0 + 2.0 = 5.0 \). \( \theta_A = 2.0/5.0 = 0.40 \), \( \theta_B = 0.40 \), empty fraction \( = 1/5.0 = 0.20 \). Option (b) would be the empty fraction if B were absent (1/3).
Level 3: Part C Style
Practice Q5. N₂ adsorption at 77 K on 0.50 g of a catalyst support gives a linear BET plot of \( x/[V(1-x)] \) against \( x = P/P_0 \) (V in cm³ STP per gram) with slope \( 0.0490\ \text{g cm}^{-3} \) and intercept \( 0.0010\ \text{g cm}^{-3} \). Take σ(N₂) = 0.162 nm². Which statements are correct?
- The monolayer capacity is 20.0 cm³ STP g⁻¹.
- The BET constant c is 50, indicating that the first layer is held much more strongly than later layers.
- The total surface area of the 0.50 g sample is about 44 m².
- The isotherm is expected to be type III.
(a) 1 and 2 only (b) 1, 2 and 3 only (c) 1 and 4 only (d) 2, 3 and 4 only
Answer: (b) 1, 2 and 3 only
- \( V_m = 1/(0.0490 + 0.0010) = 20.0\ \text{cm}^3\ \text{g}^{-1} \). Statement 1 true.
- \( c = 1 + 0.0490/0.0010 = 50 \); large c means \( \Delta H_{\text{des},1} \gg \Delta H_{\text{vap}} \). Statement 2 true.
- Specific area \( = 20.0 \times 6.022\times10^{23} \times 0.162\times10^{-18}/22414 = 87.1\ \text{m}^2\ \text{g}^{-1} \); for 0.50 g, 43.5 m². Statement 3 true.
- Large c gives a pronounced knee (type II or IV). Type III corresponds to c below about 2. Statement 4 false.
Practice Q6. For CO on a metal powder, the pressures needed to reach the same coverage are 1.2 Pa at 300 K and 15 Pa at 350 K. Which statements are correct?
- The isosteric enthalpy of adsorption is about −44 kJ mol⁻¹.
- The sign of ΔH confirms that adsorption is exothermic.
- At 400 K, a pressure lower than 15 Pa would give the same coverage.
- If the isosteric heat is found to decrease with coverage, the Langmuir assumptions do not hold for this system.
(a) 1, 2 and 4 only (b) 1 and 3 only (c) 2 and 4 only (d) 1, 2, 3 and 4
Answer: (a) 1, 2 and 4 only
- \( \Delta H = \dfrac{R\ln(15/1.2)}{1/350 - 1/300} = \dfrac{(8.314)(2.526)}{-4.762\times10^{-4}} = -44.1\ \text{kJ mol}^{-1} \). Statement 1 true.
- Negative ΔH: exothermic. Statement 2 true.
- For exothermic adsorption, maintaining θ at a higher temperature needs a higher pressure. Statement 3 false.
- Langmuir requires a coverage-independent heat; a falling isosteric heat signals heterogeneity or lateral repulsion. Statement 4 true.
Practice Q7. The surface tension of aqueous solutions of a non-ionic surfactant at 298 K falls linearly with ln c from 0.10 mM to 0.50 mM, from 56.0 to 44.0 mN m⁻¹. Which statements are correct?
- The surface excess in this range is about \( 3.0\times10^{-6} \) mol m⁻².
- The area per adsorbed molecule is about 0.55 nm².
- The surfactant is negatively adsorbed.
- At concentrations well above the CMC, γ will continue to fall at the same rate.
(a) 1 and 2 only (b) 1, 2 and 3 only (c) 2 and 4 only (d) 1 only
Answer: (a) 1 and 2 only
- \( d\gamma/d\ln c = (44.0 - 56.0)\times10^{-3}/\ln 5 = -12.0\times10^{-3}/1.609 = -7.46\times10^{-3}\ \text{N m}^{-1} \).
- \( \Gamma = 7.46\times10^{-3}/(8.314 \times 298) = 3.01\times10^{-6}\ \text{mol m}^{-2} \). Statement 1 true.
- Area \( = 1/(6.022\times10^{23} \times 3.01\times10^{-6}) = 5.5\times10^{-19}\ \text{m}^2 = 0.55\ \text{nm}^2 \). Statement 2 true.
- γ falls with c, so Γ > 0: positive adsorption. Statement 3 false.
- Above the CMC the monomer concentration hardly changes, so γ becomes almost constant. Statement 4 false.
Quick Revision Table
| Idea | Formula or fact |
|---|---|
| Exothermic adsorption | ΔG < 0, ΔS < 0 ⇒ ΔH < 0 |
| Physisorption vs chemisorption | about 20 vs about 100–400 kJ mol⁻¹; multilayer vs monolayer; non-specific vs specific |
| Residence time | \( \tau = \tau_0e^{E_d/RT} \), \( \tau_0 \sim 10^{-13} \) s |
| Langmuir | \( \theta = KP/(1+KP) \); \( P/V = 1/(KV_m) + P/V_m \) |
| Dissociative | \( \theta = (KP)^{1/2}/[1+(KP)^{1/2}] \); \( \theta\propto P^{1/2} \) at low P |
| Competitive | \( \theta_A = K_AP_A/(1 + K_AP_A + K_BP_B) \) |
| Isosteric | \( \ln(P_2/P_1) = (\Delta H/R)(1/T_2 - 1/T_1) \) at constant θ |
| Freundlich | \( x/m = kP^{1/n} \), n > 1; log–log slope 1/n |
| Temkin | \( \theta = c_1\ln(c_2P) \); heat falls linearly |
| BET | \( x/[V(1-x)] = 1/(V_mc) + (c-1)x/(V_mc) \); valid 0.05–0.30; \( V_m = 1/(s+i) \), \( c = 1+s/i \) |
| Surface area | \( S = (V_m/22414)N_A\sigma \); N₂ 0.162 nm² ⇒ 4.35 m² per cm³ STP |
| Isotherm types | I micro, II non-porous, III weak, IV meso + hysteresis, V weak meso, VI stepwise |
| Pore sizes | micro < 2 nm, meso 2–50 nm, macro > 50 nm |
| Laplace | \( \Delta P = 2\gamma/r \) |
| Kelvin | \( \ln(P/P_0) = 2\gamma V_m/(rRT) \) |
| Gibbs | \( \Gamma = -(1/RT)\,d\gamma/d\ln c \); \( 1/(2RT) \) for 1:1 ionic surfactant, no salt |
| Collision flux | \( Z_W = P/\sqrt{2\pi mk_BT} \) |
Key Takeaways
What’s Next
- Heterogeneous Catalysis: Langmuir–Hinshelwood and Eley–Rideal rate laws built on the isotherms above.
- Electrical Double Layer and Colloid Stability: adsorption of ions on colloidal particles.
- Adsorption as a separation tool: Separation Methods.
- Chapter overview: Colloids and Surfaces.