Skip to content

Absolute and Relative Errors

CSIR NET Chemical Sciences: absolute and relative error, accuracy vs precision, systematic and random errors, significant figures and propagation of errors.

  • 19 min read
  • Updated
On this page · 14 sections
  1. Prerequisites
  2. The Hook: The Same 0.1 mg on Two Weighings
  3. Error, Absolute and Relative
  4. Accuracy and Precision
  5. Types of Error
  6. Significant Figures
  7. Propagation of Errors
  8. Memory Tricks
  9. Don’t Confuse
  10. Common Mistakes
  11. Practice
  12. Quick Revision Table
  13. Key Takeaways
  14. What’s Next

Prerequisites

The Hook: The Same 0.1 mg on Two Weighings

Error, Absolute and Relative

If \( x \) is a measured value and \( x_t \) the true (or accepted) value:

$$\boxed{E_a = x - x_t} \qquad \boxed{E_r = \frac{x - x_t}{x_t}} \qquad \text{percentage error} = E_r \times 100\%$$
  • The absolute error \( E_a \) has the units of the measurement and a sign: positive when the result is high, negative when low.
  • The relative error \( E_r \) is dimensionless; it is also quoted in parts per thousand (ppt, × 1000) in analytical work.

Error vs uncertainty

When the true value is unknown, which is most of the time, we cannot calculate the error. We state an uncertainty instead: a range expected to contain the true value. The same absolute/relative split applies:

  • Absolute uncertainty: \( \pm 0.02 \) mL on a burette reading.
  • Relative uncertainty: \( 0.02/24.32 = 0.08\% \) of that reading.

The uncertainty may be an instrument tolerance (the “maximum error” of a pipette or balance) or a standard deviation from replicates. The propagation rules below work for both, with one difference noted where it matters.

Accuracy and Precision

AccuracyPrecision
Meaningcloseness of a result to the true valuecloseness of replicate results to each other
Measured byabsolute or relative error (mean − true)SD, RSD, range
Spoilt bysystematic (determinate) errorsrandom (indeterminate) errors
Needs a true value?yes (reference material, standard)no

Precision is necessary for accuracy but not sufficient: a set of results can agree closely with each other and all be wrong by the same amount.

Types of Error

graph TD
    E[Errors in a measurement] --> S["Systematic (determinate)
same sign, has a cause,
affects accuracy"] E --> R["Random (indeterminate)
both signs, Gaussian,
affects precision"] E --> G["Gross
blunders, outliers"] S --> S1[Instrumental
uncalibrated pipette, drift] S --> S2[Method
indicator end point ≠ equivalence,
coprecipitation, side reaction] S --> S3[Personal
parallax, colour judgement] S --> S4["By size: constant
or proportional"]

Systematic errors

A systematic error has a definite cause and, in principle, a definite value and sign. Repeating the measurement does not reduce it.

SourceExample
Instrumentala 25 mL pipette that actually delivers 24.95 mL; a balance out of calibration; a drifting reference electrode
Methodan indicator that changes colour after the equivalence point; slight solubility of a precipitate; an interfering ion
Personalconsistently reading the meniscus from above; a bias in judging a colour change

Constant vs proportional. A constant error has the same absolute size whatever the sample size (for example, the volume of titrant needed to change the indicator colour, or a fixed solubility loss on washing). Its relative effect shrinks as the sample grows: a 0.5 mg loss is 1% of a 50 mg precipitate but 0.1% of a 500 mg one. A proportional error grows with sample size (an interfering impurity in the sample, an error in a standard’s concentration), so its relative size stays constant.

Detecting and removing systematic error:

  • Analyse a certified reference material and compare with the certified value (a t-test, see the previous page).
  • Use an independent method on the same sample.
  • Run a blank (all reagents, no analyte) to correct for reagent contributions and indicator error.
  • Vary the sample size: a constant error shows up as a result that changes with the mass taken.
  • Calibrate glassware and instruments.

Random errors

Random errors come from many small, uncontrollable fluctuations: reading a scale, thermal noise in a detector, small temperature changes. They are equally likely to be positive or negative, follow a Gaussian distribution, and are reduced by averaging (as \( 1/\sqrt{n} \)). They are expressed as an SD.

Gross errors

Blunders: a transcription error, a spilled sample, the wrong pipette. They produce outliers, which are handled by a test such as the Q-test or by repeating the work.

Significant Figures

The significant figures of a number are all the certain digits plus the first uncertain one. Writing 24.32 mL claims the 2 in the hundredths place is uncertain.

NumberSignificant figuresNote
0.004503leading zeros are not significant; the trailing zero is
1.0404zeros between and after digits after a decimal point count
\( 2.50 \times 10^{3} \)3scientific notation makes this unambiguous
2500ambiguouswrite \( 2.5 \times 10^3 \) or \( 2.500 \times 10^3 \)

Rules for results:

  • Addition and subtraction: keep the decimal places of the term with the fewest decimal places. \( 12.11 + 0.3 = 12.4 \).
  • Multiplication and division: keep roughly the number of significant figures of the factor with the fewest. \( 4.3 \times 2.112 = 9.1 \).
  • Logarithms: the number of digits after the decimal point in the log (the mantissa) equals the significant figures of the number. \( \log(2.0 \times 10^{-3}) = -2.70 \) (two figures in 2.0, two decimals in −2.70).
  • Antilogarithms: the reverse. pH 4.37 has two decimals, so \( [\text{H}^+] = 10^{-4.37} = 4.3 \times 10^{-5} \) M, two significant figures.
  • Carry extra digits through a calculation and round only the final answer.
  • Exact numbers (stoichiometric coefficients, the 2 in \( 2\pi \), counted objects) do not limit the figures.

Propagation of Errors

A result \( y \) is usually computed from several measured quantities \( a, b, c \), each with its own uncertainty. How big is the uncertainty in \( y \)?

There are two conventions:

  • Maximum (limiting) error: assume every error has its worst-case sign, so absolute or relative errors simply add. Used for instrument tolerances and in most “maximum percentage error” questions.
  • Standard deviation (random) error: independent random errors partly cancel, so they add in quadrature (square, add, square-root). Used when the uncertainties are SDs.

Quadrature always gives a smaller number than straight addition. Read the question: “maximum error” means add; “standard deviation of the result” means quadrature.

The rules

CalculationMaximum errorStandard deviation
\( y = a + b - c \)\( E_y = E_a + E_b + E_c \) (absolute)\( s_y = \sqrt{s_a^2 + s_b^2 + s_c^2} \) (absolute)
\( y = ab/c \)\( \frac{E_y}{y} = \frac{E_a}{a} + \frac{E_b}{b} + \frac{E_c}{c} \)\( \frac{s_y}{y} = \sqrt{\left(\frac{s_a}{a}\right)^2 + \left(\frac{s_b}{b}\right)^2 + \left(\frac{s_c}{c}\right)^2} \)
\( y = k a \) (\( k \) exact)\( E_y = k E_a \)\( s_y = k s_a \)
\( y = a^n \)\( \frac{E_y}{y} = n\frac{E_a}{a} \)\( \frac{s_y}{y} = n\frac{s_a}{a} \)
\( y = \log_{10} a \)\( E_y = 0.434\,\frac{E_a}{a} \)\( s_y = 0.434\,\frac{s_a}{a} \)
\( y = \ln a \)\( E_y = \frac{E_a}{a} \)\( s_y = \frac{s_a}{a} \)
\( y = 10^{a} \)\( \frac{E_y}{y} = 2.303\,E_a \)\( \frac{s_y}{y} = 2.303\,s_a \)
\( y = e^{a} \)\( \frac{E_y}{y} = E_a \)\( \frac{s_y}{y} = s_a \)

The one-line summary: sums and differences carry absolute errors; products and quotients carry relative errors; a power multiplies the relative error by the exponent; a log turns a relative error into an absolute one.

Note that \( y = a^2 \) is not the same as \( y = a \times b \) with \( b = a \): the two factors are the same measurement, so their errors are fully correlated and the relative error doubles (\( 2 s_a/a \)), rather than growing by \( \sqrt{2} \).

The general formula

All the rows above come from one rule. For \( y = f(a, b, c, \dots) \) with independent errors,

$$\boxed{s_y^2 = \left(\frac{\partial y}{\partial a}\right)^2 s_a^2 + \left(\frac{\partial y}{\partial b}\right)^2 s_b^2 + \left(\frac{\partial y}{\partial c}\right)^2 s_c^2 + \cdots}$$

For the maximum error, drop the squares and add the absolute values of each term. If the errors in \( a \) and \( b \) are not independent, a covariance term \( 2\,\frac{\partial y}{\partial a}\frac{\partial y}{\partial b}\,\text{cov}(a, b) \) is added; see Linear Regression, Covariance and Correlation.

Worked examples

Which measurement to improve

Because random errors add in quadrature, the largest relative uncertainty dominates. If one term is 0.08% and another 0.01%, the result is \( \sqrt{0.0064 + 0.0001} = 0.0806\% \): the small term is irrelevant. Spend the effort on the biggest contributor.

A related classic: in spectrophotometry, an uncertainty in transmittance produces the smallest relative error in concentration near \( A = 0.434 \) (for a constant absolute uncertainty in \( T \)). The derivation uses the log rule above; the result is discussed in Spectroscopic Methods of Analysis.

Memory Tricks

Don’t Confuse

ThisvsThat
Absolute error (units, signed)relative error (dimensionless, %, ppt)
Accuracy: mean vs true valueprecision: results vs each other
Systematic error: one sign, not reduced by repeatsrandom error: both signs, reduced by averaging
Constant error: relative size falls with bigger sampleproportional error: relative size constant
Maximum error: \( E_a + E_b \)standard error: \( \sqrt{s_a^2 + s_b^2} \)
Error of \( a^2 \): \( 2 s_a/a \)error of \( a \times b \) (independent): \( \sqrt{(s_a/a)^2 + (s_b/b)^2} \)
Error: needs the true valueuncertainty: an estimated range when the truth is unknown

Common Mistakes

Practice

All questions below are original practice questions written for this page. They are not from any CSIR NET paper.

Level 1: Foundation

  1. Distinguish absolute error from relative error in one line each.
  2. The radius of a spherical particle is measured with a 2% error. What is the percentage error in its cross-sectional area?
  3. State the rule for the uncertainty in \( y = \log_{10} x \).
Answers
  1. Absolute error = measured − true value, in the units of the measurement. Relative error = absolute error ÷ true value, dimensionless (often in % or ppt).
  2. 4%. Area \( \propto r^2 \), so the relative error doubles.
  3. \( s_y = 0.434\,s_x/x \): the relative error in \( x \), times \( 1/\ln 10 \), is the absolute error in \( y \).

Level 2: Part B Style

Practice Q1. A reference sample contains 50.0 mg of analyte. An analyst finds 49.6 mg. The relative error is:

(a) −0.4 mg (b) −0.8% (c) +0.8% (d) −0.4%

Answer: (b) −0.8%

Absolute error \( = 49.6 - 50.0 = -0.4 \) mg. Relative error \( = -0.4/50.0 = -0.008 = -0.8\% \).

(a) is the absolute error, not the relative one; (c) has the wrong sign; (d) treats the absolute error as a percentage.

Practice Q2. The density of a cubic crystal is found from its mass and edge length. The edge is measured with a maximum error of 1% and the mass with 0.5%. The maximum percentage error in the density is:

(a) 1.5% (b) 2.5% (c) 3.5% (d) 4.0%

Answer: (c) 3.5%

\( \rho = m/a^3 \). Maximum relative error \( = 0.5 + 3(1) = 3.5\% \).

(a) forgets the cube.

Practice Q3. A pH meter reading is uncertain by ±0.01 pH unit. The corresponding relative uncertainty in [H⁺] is about:

(a) 0.01% (b) 0.43% (c) 1% (d) 2.3%

Answer: (d) 2.3%

\( [\text{H}^+] = 10^{-\text{pH}} \), so \( s_{[\text{H}^+]}/[\text{H}^+] = 2.303 \times 0.01 = 0.023 \), about 2.3%.

(b) uses 0.434 (the rule for the reverse direction).

Practice Q4. Which of the following is a systematic (determinate) error?

(a) Fluctuation in the last digit of a balance reading caused by air currents (b) Use of an indicator whose colour change consistently occurs after the equivalence point (c) Small random variation in reading a burette meniscus (d) Electronic noise in a detector signal

Answer: (b)

An indicator that always changes late gives a titre that is always high: a definite cause with a definite sign, a method error. Removing it needs an indicator blank or a better indicator, not more replicates.

(a), (c) and (d) are random errors: both signs, reduced by averaging.

Level 3: Part C Style

Practice Q5. A first-order reaction has \( E_a = 80 \) kJ mol⁻¹. Its rate constant is measured at 310 K, but the bath temperature is uncertain by ±0.5 K. Take \( R = 8.314 \) J K⁻¹ mol⁻¹. The resulting relative uncertainty in \( k \), and in the half-life, are closest to:

(a) 5.0% in \( k \); 5.0% in \( t_{1/2} \) (b) 5.0% in \( k \); 2.5% in \( t_{1/2} \) (c) 10% in \( k \); 10% in \( t_{1/2} \) (d) 0.16% in \( k \); 0.16% in \( t_{1/2} \)

Answer: (a)

\( \frac{dk}{k} = \frac{E_a}{RT^2}\,dT = \frac{80\,000}{8.314 \times 310^2} \times 0.5 = 0.1001 \times 0.5 = 0.050 \), i.e. 5.0%.

\( t_{1/2} = 0.693/k \). The constant 0.693 is exact, and a quotient carries the relative error unchanged, so \( t_{1/2} \) is also uncertain by 5.0% (in the opposite direction).

(c) forgets the 0.5 K (uses 1 K). (d) is just \( 0.5/310 \), the relative error in \( T \), ignoring the exponential.

Practice Q6. The molar mass of a volatile liquid is found from \( M = \frac{mRT}{pV} \) (Dumas method). The relative standard uncertainties are: mass 0.40%, temperature 1 K at 300 K, pressure 0.50%, volume 0.20% (\( R \) exact). Consider:

  1. The relative uncertainty in \( T \) is 0.33%.
  2. The relative standard uncertainty in \( M \) is about 0.75%.
  3. The maximum relative error in \( M \) is about 1.43%.
  4. Halving the volume uncertainty would reduce the standard uncertainty in \( M \) more than halving the pressure uncertainty would.

Which statements are correct?

(a) 1 and 2 only (b) 1, 2 and 3 only (c) 2, 3 and 4 only (d) 1, 2, 3 and 4

Answer: (b) 1, 2 and 3 only
  1. \( 1/300 = 0.33\% \). Correct.
  2. \( \sqrt{0.40^2 + 0.33^2 + 0.50^2 + 0.20^2} = \sqrt{0.160 + 0.111 + 0.250 + 0.040} = \sqrt{0.561} = 0.75\% \). Correct.
  3. \( 0.40 + 0.33 + 0.50 + 0.20 = 1.43\% \). Correct.
  4. Halving the volume term: \( \sqrt{0.160 + 0.111 + 0.250 + 0.010} = 0.73\% \). Halving the pressure term: \( \sqrt{0.160 + 0.111 + 0.0625 + 0.040} = 0.61\% \). Improving the pressure, the largest contributor, helps more. Incorrect.

Practice Q7. A certified reference solution contains 0.2500 M Cu²⁺. Two methods give (five replicates each):

  • Method X: mean 0.2501 M, \( s = 0.0030 \) M
  • Method Y: mean 0.2560 M, \( s = 0.0004 \) M

Consider:

  1. Method Y is more precise than method X.
  2. Method X is more accurate than method Y.
  3. The relative error of the mean of method Y is +2.4%.
  4. Averaging more replicates with method Y would bring its mean close to 0.2500 M.

Which statements are correct?

(a) 1 and 2 only (b) 1, 2 and 3 only (c) 2 and 4 only (d) 1, 2, 3 and 4

Answer: (b) 1, 2 and 3 only
  1. Y’s \( s \) (0.0004 M) is far smaller than X’s (0.0030 M). Correct.
  2. X’s mean is 0.0001 M off (+0.04%); Y’s is 0.0060 M off. Correct.
  3. \( (0.2560 - 0.2500)/0.2500 = 0.024 = +2.4\% \). Correct.
  4. Y’s error is systematic. Averaging reduces random error only; the mean of Y stays near 0.2560 M. Incorrect.

Quick Revision Table

IdeaFormula or fact
Absolute error\( E_a = x - x_t \) (units, sign)
Relative error\( E_r = E_a/x_t \); × 100 for %, × 1000 for ppt
Accuracy / precisionerror of mean / SD of replicates
Systematic errorone sign, cause can be found, not cut by repeats
Random errorboth signs, Gaussian, falls as \( 1/\sqrt{n} \)
Constant vs proportionalconstant: relative effect falls with sample size
Sum, differenceabsolute errors: add (max) or \( \sqrt{\sum s^2} \)
Product, quotientrelative errors: add (max) or \( \sqrt{\sum (s/x)^2} \)
Power \( a^n \)relative error × \( n \)
\( \log_{10} a \)\( s_y = 0.434\,s_a/a \)
\( 10^a \)\( s_y/y = 2.303\,s_a \)
Arrhenius sensitivity\( dk/k = (E_a/RT^2)\,dT \)
Sig figs in logsdecimals in the log = sig figs in the number

Key Takeaways

What’s Next