Skip to content

Electrochemical Cells, Redox Systems and the Nernst Equation

CSIR NET electrochemistry: cell notation, electrode types, E° and ΔG°, the Nernst equation, Latimer and Frost diagrams, pH and Ksp effects, concentration cells.

  • 21 min read
  • Updated
On this page · 16 sections
  1. Prerequisites
  2. The Hook: A Battery That Knows the Equilibrium Constant
  3. 1. Cells, Electrodes and Conventions
  4. 2. The Nernst Equation
  5. 3. How pH, Precipitation and Complexation Shift Potentials
  6. 4. Redox Systems: Latimer and Frost Diagrams
  7. 5. Thermodynamics From Cell Potentials
  8. 6. Concentration Cells and Liquid Junctions
  9. 7. Faraday’s Laws in One Line
  10. Memory Tricks
  11. Don’t Confuse
  12. Common Mistakes
  13. Practice
  14. Quick Revision Table
  15. Key Takeaways
  16. What’s Next

Prerequisites

  • Acid–Base Concepts: pH, conjugate pairs and equilibrium constants, which reappear in every pH-dependent potential.
  • Chemical Bonds and Biophysical Chemistry: the same relation \( \Delta G^{\circ\prime} = -nF\Delta E^{\circ\prime} \) seen from the biochemist’s side.
  • Basic thermodynamics: \( \Delta G = \Delta H - T\Delta S \) and \( \Delta G^\circ = -RT\ln K \).

The Hook: A Battery That Knows the Equilibrium Constant

1. Cells, Electrodes and Conventions

Galvanic and electrolytic cells

Galvanic (voltaic) cellElectrolytic cell
Energy conversionchemical → electricalelectrical → chemical
Reactionspontaneous, \( \Delta G < 0 \)driven, \( \Delta G > 0 \)
Anode (oxidation)negative terminalpositive terminal
Cathode (reduction)positive terminalnegative terminal

The definitions anode = oxidation, cathode = reduction never change. Only the sign of each terminal changes between the two kinds of cell.

Cell notation (IUPAC)

$$\text{Zn(s)} \,|\, \text{Zn}^{2+}(aq) \,\|\, \text{Cu}^{2+}(aq) \,|\, \text{Cu(s)}$$
  • A single bar | is a phase boundary; a double bar ‖ is a salt bridge whose junction potential is taken as eliminated; a dashed or single bar between two solutions is a liquid junction that is not eliminated.
  • Species in the same phase are separated by commas: Pt | Fe³⁺, Fe²⁺.
  • By convention the cell is written so that
$$\boxed{E_{\text{cell}} = E_{\text{right}} - E_{\text{left}}}$$

where both are reduction potentials. The cell reaction is the one in which reduction occurs at the right-hand electrode. If \( E_{\text{cell}} > 0 \), that reaction is spontaneous as written; if \( E_{\text{cell}} < 0 \), the reverse is.

Electrode free energy and the cell potential

The reversible (zero-current) cell potential is related to the Gibbs energy of the cell reaction, for n electrons transferred per formula of reaction:

$$\boxed{\Delta G = -nFE} \qquad \boxed{\Delta G^\circ = -nFE^\circ = -RT\ln K}$$

with \( F = 96\,485 \) C mol⁻¹. Combining:

$$\boxed{\ln K = \frac{nFE^\circ}{RT}} \qquad \log K = \frac{nE^\circ}{0.05916\ \text{V}} \ \ (25\ ^\circ\text{C})$$

For the Daniell cell (n = 2, E° = 1.10 V): \( \Delta G^\circ = -2 \times 96\,485 \times 1.10 = -212.3 \) kJ mol⁻¹ and \( \log K = 2 \times 1.10/0.05916 = 37.2 \).

The standard hydrogen electrode and standard potentials

Single electrode potentials cannot be measured, only differences. The standard hydrogen electrode (SHE), Pt | H₂(g, 1 bar) | H⁺(a = 1), is assigned E° = 0 at all temperatures. A standard electrode potential E° is the potential of the cell SHE ‖ couple, with all species in their standard states.

Selected standard reduction potentials at 25 °C (values used on this page):

CoupleE° / VCoupleE° / V
Li⁺/Li−3.04Cu²⁺/Cu⁺+0.153
Zn²⁺/Zn−0.762AgCl/Ag, Cl⁻+0.222
Fe²⁺/Fe−0.447Cu²⁺/Cu+0.337
2H⁺/H₂0 (definition)Cu⁺/Cu+0.521
O₂/H₂O₂+0.695Fe³⁺/Fe²⁺+0.771
Ag⁺/Ag+0.799O₂, 4H⁺/2H₂O+1.229
Cl₂/Cl⁻+1.36MnO₄⁻, 8H⁺/Mn²⁺+1.51
H₂O₂, 2H⁺/2H₂O+1.776Br₂/Br⁻+1.07

The more positive E°, the stronger the oxidised form as an oxidant. A couple higher in the table oxidises the reduced form of any couple below it (thermodynamically; kinetics may be slow).

Types of electrode

TypeExamplePotential depends on
Metal–metal ion (first kind)Cu | Cu²⁺\( a_{\text{Cu}^{2+}} \)
Gas electrodePt | H₂ | H⁺; Pt | Cl₂ | Cl⁻gas pressure and ion activity
AmalgamNa(Hg) | Na⁺activity of Na in Hg and of Na⁺
Metal–insoluble salt–anion (second kind)Ag | AgCl | Cl⁻; Hg | Hg₂Cl₂ | Cl⁻\( a_{\text{Cl}^-} \) only
Redox (inert metal)Pt | Fe³⁺, Fe²⁺ratio \( a_{\text{Fe}^{3+}}/a_{\text{Fe}^{2+}} \)
Membraneglass electrode\( a_{\text{H}^+} \) across the membrane

Electrodes of the second kind make good reference electrodes: with the anion activity fixed (saturated KCl), the potential is constant. The saturated calomel electrode (SCE) sits at about +0.241 V and the Ag/AgCl electrode in saturated KCl at about +0.197 V against SHE at 25 °C. The glass electrode and ion-selective electrodes are covered in Electroanalytical Methods.

2. The Nernst Equation

For a half-reaction written as a reduction, Ox + ne⁻ → Red, or for a whole cell reaction with reaction quotient Q:

$$\boxed{E = E^\circ - \frac{RT}{nF}\ln Q = E^\circ - \frac{0.05916\ \text{V}}{n}\log Q \quad (25\ ^\circ\text{C})}$$

Derivation in two lines. \( \Delta G = \Delta G^\circ + RT\ln Q \). Divide by \( -nF \): \( E = E^\circ - (RT/nF)\ln Q \).

At equilibrium \( \Delta G = 0 \), so \( E = 0 \) and \( Q = K \), which recovers \( \ln K = nFE^\circ/RT \). A cell at equilibrium is a “dead battery”.

For a half-cell: \( E = E^\circ - \dfrac{0.05916}{n}\log\dfrac{a_{\text{Red}}}{a_{\text{Ox}}} \).

The numerical factor \( 2.303RT/F \) is 0.05916 V at 298.15 K. It is proportional to T: about 0.0542 V at 0 °C and about 0.0661 V at 60 °C (useful when a question gives a non-standard temperature).

Worked example. Zn | Zn²⁺(0.10) ‖ Cu²⁺(0.0010) | Cu, activities equal to concentrations.

$$E = 1.10 - \frac{0.05916}{2}\log\frac{0.10}{0.0010} = 1.10 - 0.0592 = 1.041\ \text{V}$$

A hundredfold change in the quotient moves a two-electron cell by only 59 mV. Potentials are logarithmic in concentration; this is why potentiometry has a wide range and why titration end points show as sharp jumps (see Conductometric and Potentiometric Titrations).

Activities, not concentrations

Strictly the Nernst equation uses activities, \( a = \gamma\,m/m^\circ \). In ionic solutions γ is well below 1 even at millimolar concentration. Debye–Hückel theory supplies γ (see Debye–Hückel Theory). The standard way to get E° from data is to measure E at several molalities and extrapolate to zero ionic strength, where γ → 1.

Formal potential

In a specified medium (for example 1 M H₂SO₄ or 1 M HClO₄), the formal potential \( E^{\circ\prime} \) is the measured potential when the analytical concentrations of Ox and Red are equal. It absorbs activity coefficients, complexation and acid–base side reactions:

$$E = E^{\circ\prime} - \frac{0.05916}{n}\log\frac{c_{\text{Red}}}{c_{\text{Ox}}}$$

Fe³⁺/Fe²⁺ has E° = 0.771 V but a formal potential of about 0.68 V in 1 M H₂SO₄, because Fe³⁺ is complexed by sulfate more strongly than Fe²⁺. Titration calculations use formal potentials.

3. How pH, Precipitation and Complexation Shift Potentials

Every chemical equilibrium that removes one partner of a redox couple shifts its potential. This is where most Part C questions live.

pH dependence

For a half-reaction Ox + mH⁺ + ne⁻ → Red + (m/2)H₂O:

$$\boxed{E = E^\circ - \frac{0.05916}{n}\log\frac{a_{\text{Red}}}{a_{\text{Ox}}} - \frac{0.05916\,m}{n}\,\text{pH}}$$

The slope of E against pH is \( -0.05916\,m/n \) V per pH unit.

Couplem/nSlope (V/pH)E at unit activities other than H⁺
2H⁺ + 2e⁻ → H₂1−0.0592\( -0.0592\,\text{pH} \)
O₂ + 4H⁺ + 4e⁻ → 2H₂O1−0.0592\( 1.229 - 0.0592\,\text{pH} \)
MnO₄⁻ + 8H⁺ + 5e⁻ → Mn²⁺ + 4H₂O8/5−0.0947\( 1.51 - 0.0947\,\text{pH} \)

Consequence. At pH 3 the permanganate potential drops to \( 1.51 - 0.0947 \times 3 = 1.23 \) V, below the Cl₂/Cl⁻ potential (1.36 V). Acidic permanganate oxidises chloride at pH 0 but not at pH 3 under standard chloride conditions, while it still oxidises bromide (1.07 V) and iodide.

The two lines for H₂ and O₂ are parallel, 1.229 V apart at every pH: that is the thermodynamic stability window of water. An E–pH plot of this kind is a Pourbaix diagram. Horizontal lines are pure electron transfers (no H⁺), vertical lines are pure acid–base or precipitation steps (no electrons), and sloping lines involve both.

Precipitation: Ksp from potentials

AgCl(s) + e⁻ → Ag(s) + Cl⁻ is the Ag⁺/Ag couple with [Ag⁺] fixed by the solubility product. Subtract the two half-reactions:

$$\text{AgCl(s)} \rightleftharpoons \text{Ag}^+ + \text{Cl}^- \qquad E^\circ = E^\circ_{\text{AgCl/Ag}} - E^\circ_{\text{Ag}^+/\text{Ag}} = 0.222 - 0.799 = -0.577\ \text{V}$$$$\log K_{sp} = \frac{1 \times (-0.577)}{0.05916} = -9.75 \quad\Rightarrow\quad K_{sp} = 1.8 \times 10^{-10}$$

General result for an electrode of the second kind:

$$\boxed{E^\circ_{\text{MX/M}} = E^\circ_{\text{M}^+/\text{M}} + \frac{0.05916}{n}\log K_{sp}}$$

The smaller Ksp, the lower the potential: precipitating the oxidised form makes the metal easier to oxidise.

Complexation

Complexing the oxidised form lowers the potential; complexing the reduced form raises it. For a metal ion forming a complex with overall formation constant β:

$$E^\circ_{\text{complex}} = E^\circ_{\text{aqua}} - \frac{0.05916}{n}\log\frac{\beta_{\text{Ox}}}{\beta_{\text{Red}}}$$

This is why cyanide lets gold dissolve in air (Au(I) is strongly stabilised as [Au(CN)₂]⁻), and why ligands that prefer a lower oxidation state (π-acceptors such as bipyridine and phenanthroline with Fe²⁺) raise the Fe(III)/Fe(II) potential. Biological electron-transfer centres tune their potentials the same way (see Biological Electron Transfer).

4. Redox Systems: Latimer and Frost Diagrams

Latimer diagrams

A Latimer diagram lists the oxidation states of an element from highest (left) to lowest (right), with the standard potential of each step written over the arrow. For copper in acid:

$$\text{Cu}^{2+} \xrightarrow{+0.153} \text{Cu}^{+} \xrightarrow{+0.521} \text{Cu}$$

Combining non-adjacent steps. Add free energies, not potentials:

$$\boxed{E^\circ_{13} = \frac{n_1 E^\circ_1 + n_2 E^\circ_2}{n_1 + n_2}}$$

Cu²⁺/Cu: \( (1 \times 0.153 + 1 \times 0.521)/2 = 0.337 \) V, which is the tabulated value. For iron, Fe³⁺ → Fe²⁺ (+0.771, n = 1) and Fe²⁺ → Fe (−0.447, n = 2):

$$E^\circ(\text{Fe}^{3+}/\text{Fe}) = \frac{0.771 + 2(-0.447)}{3} = -0.041\ \text{V}$$

Disproportionation test. A species disproportionates if the potential on its right is greater than the potential on its left (\( E^\circ_{\text{right}} > E^\circ_{\text{left}} \)). Cu⁺ has 0.521 on its right and 0.153 on its left, so

$$2\text{Cu}^+ \rightarrow \text{Cu}^{2+} + \text{Cu} \qquad E^\circ = 0.521 - 0.153 = 0.368\ \text{V}, \quad K = 10^{0.368/0.05916} = 1.7 \times 10^{6}$$

Aqueous Cu⁺ disproportionates unless stabilised by precipitation (CuI, CuCl) or complexation, or in a solvent such as acetonitrile.

Hydrogen peroxide is the other classic: O₂ → H₂O₂ (+0.695) and H₂O₂ → H₂O (+1.776). The right-hand potential is larger, so H₂O₂ disproportionates to O₂ and H₂O (slowly, catalysed by metal ions and catalase). The combined O₂/H₂O potential is \( (2 \times 0.695 + 2 \times 1.776)/4 = 1.236 \approx 1.23 \) V.

Frost diagrams

A Frost (oxidation-state) diagram plots \( NE^\circ \) for the couple X(N)/X(0) (in volts) against oxidation number N, with the element at (0, 0). Since the reduction X(N) → X(0) has \( \Delta G^\circ = -NFE^\circ \), the quantity \( NE^\circ \) equals \( \Delta G^\circ/F \) for forming X(N) from the element: the higher a point, the higher the Gibbs energy of that species.

FeatureMeaning
Slope of the line joining two pointsE° of that couple
Steep line rising to the right (high N)strongly oxidising high state
Lowest pointthe most stable oxidation state
A point above the line joining its neighboursunstable to disproportionation (Cu⁺, H₂O₂, MnO₄²⁻ in acid)
A point below the line joining its neighboursneighbours comproportionate to it

Frost and Latimer diagrams carry the same information; Frost diagrams make stability visible at a glance. The lanthanide and actinide versions are discussed in Redox Chemistry of Lanthanides and Actinides.

graph LR
    A["Latimer diagram
E° over each step"] --> B["Need a non-adjacent couple?
E = Σ nE / Σ n"] A --> C["Is a species stable?
E(right) > E(left) means
it disproportionates"] B --> D["ΔG° = -nFE°
log K = nE°/0.05916"] C --> D

5. Thermodynamics From Cell Potentials

Since \( \Delta G = -nFE \) and \( (\partial \Delta G/\partial T)_p = -\Delta S \):

$$\boxed{\Delta S^\circ = nF\left(\frac{\partial E^\circ}{\partial T}\right)_p} \qquad \boxed{\Delta H^\circ = -nF\left[E^\circ - T\left(\frac{\partial E^\circ}{\partial T}\right)_p\right]}$$

The second is the Gibbs–Helmholtz equation for a cell. A positive temperature coefficient means the reaction gains entropy, and the reversible cell absorbs heat \( T\Delta S \) from the surroundings while working. A cell with \( \partial E/\partial T = 0 \) converts its enthalpy change completely into electrical work.

Fuel cell efficiency. For H₂ + ½O₂ → H₂O(l) at 25 °C, \( \Delta G^\circ = -237.1 \) kJ mol⁻¹ and \( \Delta H^\circ = -285.8 \) kJ mol⁻¹. The cell potential is \( 237\,100/(2 \times 96\,485) = 1.229 \) V and the maximum (thermodynamic) efficiency is \( \Delta G^\circ/\Delta H^\circ = 0.83 \). Unlike a heat engine, a fuel cell is not limited by the Carnot factor.

6. Concentration Cells and Liquid Junctions

In a concentration cell both electrodes involve the same couple; E° = 0 and the whole potential comes from the Nernst term.

Electrolyte concentration cell (salt bridge):

$$\text{Ag} \,|\, \text{Ag}^+(a_1) \,\|\, \text{Ag}^+(a_2) \,|\, \text{Ag} \qquad E = 0.05916\log\frac{a_2}{a_1}$$

With \( a_2 = 0.10 \) and \( a_1 = 0.0010 \): E = 0.118 V. Silver dissolves on the dilute side and deposits on the concentrated side, so the cell runs until the two activities are equal.

Electrode concentration cell: two hydrogen electrodes at different pressures in the same acid, \( E = (0.05916/2)\log(p_1/p_2) \); or two amalgams of different metal content.

pH from a cell. Pt | H₂(1 bar) | H⁺(unknown) ‖ SCE gives \( E = E_{\text{SCE}} + 0.05916\,\text{pH} \), so pH rises by one unit for every 59.2 mV.

Liquid junction potentials

Where two different solutions touch directly, ions diffuse at different speeds and a small potential appears. For two solutions of the same 1:1 electrolyte (activity a₁ on the left, a₂ on the right), with transport numbers \( t_+ \) and \( t_- \):

$$E_j = (t_+ - t_-)\,\frac{RT}{F}\ln\frac{a_1}{a_2}$$

A salt bridge of concentrated KCl (or NH₄NO₃) minimises \( E_j \) because \( t_+ \approx t_- \approx 0.5 \) for these salts and the bridge ions dominate the junction. HCl, with \( t_+ \approx 0.82 \), gives a large junction potential. Transport numbers and their measurement are on the Conductance and Kohlrausch’s Law page.

A concentration cell with transference (direct junction) therefore gives a potential that depends on the transport numbers. For electrodes reversible to the cation:

$$E_t = 2t_-\,\frac{RT}{F}\ln\frac{a_{\pm,2}}{a_{\pm,1}}$$

and for electrodes reversible to the anion, \( t_- \) is replaced by \( t_+ \) (with the activity ratio inverted). Comparing \( E_t \) with the potential of the equivalent cell without transference (\( 2(RT/F)\ln(a_{\pm,2}/a_{\pm,1}) \) for a 1:1 electrolyte) gives a transport number directly.

7. Faraday’s Laws in One Line

The charge passed fixes the amount reacted at each electrode:

$$n = \frac{Q}{zF} = \frac{It}{zF}$$

Passing 1 F deposits one mole of Ag, half a mole of Cu, a third of a mole of Al. The same law underlies coulometry and the Hittorf method for transport numbers.

Memory Tricks

Don’t Confuse

ThisvsThat
\( E^\circ \): all species at unit activity\( E^{\circ\prime} \) (formal): equal analytical concentrations in a stated medium
\( E^\circ \) is intensive (does not scale with coefficients)\( \Delta G^\circ \) is extensive (doubles when the equation doubles)
Anode in a galvanic cell: negative terminalanode in an electrolytic cell: positive terminal
Concentration cell without transference (salt bridge)with transference (direct junction; depends on \( t_\pm \))
Frost point above the line of its neighbours: disproportionatespoint below the line: formed by comproportionation
Electrode of the first kind: responds to the cationsecond kind (Ag/AgCl): responds to the anion

Common Mistakes

Practice

All questions below are original practice questions written for this page. They are not from any CSIR NET paper. Use \( F = 96\,485 \) C mol⁻¹, T = 298.15 K and 2.303RT/F = 0.05916 V unless stated.

Level 1: Foundation

  1. Calculate ΔG° for a two-electron cell reaction with E° = 1.10 V.
  2. What is the value of 2.303RT/F at 25 °C?
  3. In Pt | H₂ | H⁺ ‖ Ag⁺ | Ag, at which electrode does reduction occur?
Answers
  1. \( \Delta G^\circ = -2 \times 96\,485 \times 1.10 = -2.12 \times 10^5 \) J mol⁻¹ = −212 kJ mol⁻¹.
  2. 0.05916 V (8.314 × 298.15 × 2.303 / 96 485).
  3. At the right-hand (silver) electrode: Ag⁺ + e⁻ → Ag. The hydrogen electrode on the left is the anode.

Level 2: Part B Style

Practice Q1. For Zn | Zn²⁺(0.10 M) ‖ Cu²⁺(0.0010 M) | Cu with E° = 1.10 V (activities equal to concentrations), the cell potential at 25 °C is closest to:

(a) 1.159 V (b) 1.100 V (c) 1.041 V (d) 0.982 V

Answer: (c)

Cell reaction Zn + Cu²⁺ → Zn²⁺ + Cu, n = 2, \( Q = [\text{Zn}^{2+}]/[\text{Cu}^{2+}] = 100 \).

\( E = 1.10 - (0.05916/2)\log 100 = 1.10 - 0.0592 = 1.041 \) V. Option (a) inverts Q; option (d) uses n = 1.

Practice Q2. Given E°(Cu²⁺/Cu⁺) = 0.153 V and E°(Cu⁺/Cu) = 0.521 V, the equilibrium constant for 2Cu⁺(aq) ⇌ Cu²⁺(aq) + Cu(s) at 25 °C is about:

(a) \( 1.7 \times 10^{6} \) (b) \( 6.0 \times 10^{-7} \) (c) \( 1.3 \times 10^{3} \) (d) \( 2.8 \times 10^{12} \)

Answer: (a)

Reduction Cu⁺ → Cu (0.521 V) at the cathode, oxidation Cu⁺ → Cu²⁺ (reverse of 0.153 V) at the anode. \( E^\circ = 0.521 - 0.153 = 0.368 \) V, n = 1.

\( \log K = 0.368/0.05916 = 6.22 \), \( K = 1.7 \times 10^{6} \). Option (b) is the reciprocal (comproportionation constant); (d) uses n = 2.

Practice Q3. Using E°(Fe³⁺/Fe²⁺) = +0.771 V and E°(Fe²⁺/Fe) = −0.447 V, E°(Fe³⁺/Fe) is:

(a) +0.324 V (b) +0.162 V (c) −0.041 V (d) −0.123 V

Answer: (c)

\( E^\circ = [1(0.771) + 2(-0.447)]/3 = (0.771 - 0.894)/3 = -0.041 \) V. Option (a) is the simple sum, (b) the simple average.

Practice Q4. Given E°(Ag⁺/Ag) = 0.799 V and E°(AgCl/Ag, Cl⁻) = 0.222 V, Ksp of AgCl at 25 °C is about:

(a) \( 1.8 \times 10^{-10} \) (b) \( 1.3 \times 10^{-5} \) (c) \( 3.2 \times 10^{-20} \) (d) \( 5.6 \times 10^{9} \)

Answer: (a)

AgCl → Ag⁺ + Cl⁻ is AgCl/Ag (cathode) minus Ag⁺/Ag (anode): \( E^\circ = 0.222 - 0.799 = -0.577 \) V.

\( \log K_{sp} = -0.577/0.05916 = -9.75 \), \( K_{sp} = 1.8 \times 10^{-10} \). Option (b) is the molar solubility \( \sqrt{K_{sp}} \).

Level 3: Part C Style

Practice Q5. A cell with n = 2 has E° = 0.6750 V at 298.15 K and \( (\partial E^\circ/\partial T)_p = -6.5 \times 10^{-4} \) V K⁻¹ (hypothetical data). Which set of values is correct for the cell reaction?

(a) ΔG° = −130.3 kJ mol⁻¹, ΔS° = −125.4 J K⁻¹ mol⁻¹, ΔH° = −167.7 kJ mol⁻¹ (b) ΔG° = −65.1 kJ mol⁻¹, ΔS° = −62.7 J K⁻¹ mol⁻¹, ΔH° = −83.8 kJ mol⁻¹ (c) ΔG° = −130.3 kJ mol⁻¹, ΔS° = +125.4 J K⁻¹ mol⁻¹, ΔH° = −92.9 kJ mol⁻¹ (d) ΔG° = −130.3 kJ mol⁻¹, ΔS° = −125.4 J K⁻¹ mol⁻¹, ΔH° = −92.9 kJ mol⁻¹

Answer: (a)
  • \( \Delta G^\circ = -nFE^\circ = -2 \times 96\,485 \times 0.6750 = -130\,255 \) J mol⁻¹ = −130.3 kJ mol⁻¹.
  • \( \Delta S^\circ = nF(\partial E^\circ/\partial T) = 2 \times 96\,485 \times (-6.5 \times 10^{-4}) = -125.4 \) J K⁻¹ mol⁻¹.
  • \( \Delta H^\circ = \Delta G^\circ + T\Delta S^\circ = -130.26 + 298.15 \times (-0.1254) = -167.7 \) kJ mol⁻¹.

The reaction loses entropy, so the reversible cell releases heat \( |T\Delta S^\circ| \approx 37.4 \) kJ mol⁻¹ to the surroundings in addition to its electrical work. Option (b) uses n = 1; (c) and (d) mishandle the sign of ΔS° or of \( T\Delta S^\circ \).

Practice Q6. E°(MnO₄⁻, H⁺/Mn²⁺) = 1.51 V, E°(Cl₂/Cl⁻) = 1.36 V, E°(Br₂/Br⁻) = 1.07 V, E°(O₂, H⁺/H₂O) = 1.229 V. Take all species other than H⁺ at unit activity. Which statements are correct?

  1. The potential of the MnO₄⁻/Mn²⁺ couple falls by about 95 mV per pH unit.
  2. At pH 3, permanganate can still oxidise Cl⁻ to Cl₂.
  3. At pH 3, permanganate can still oxidise Br⁻ to Br₂.
  4. At pH 0, permanganate is thermodynamically able to oxidise water to O₂, even though its acidic solutions keep for weeks.

(a) 1, 3 and 4 only (b) 1 and 2 only (c) 2 and 3 only (d) 1, 2, 3 and 4

Answer: (a) 1, 3 and 4 only
  1. Correct. m = 8, n = 5: slope \( = 0.05916 \times 8/5 = 0.0947 \) V per pH.
  2. Wrong. At pH 3, \( E = 1.51 - 0.0947 \times 3 = 1.226 \) V < 1.36 V.
  3. Correct. 1.226 V > 1.07 V.
  4. Correct. 1.51 V > 1.229 V, so the oxidation of water is favourable; it is kinetically slow, which is why permanganate solutions keep. (Both lines fall with pH, permanganate faster: the gap \( 0.281 - 0.0355\,\text{pH} \) V closes near pH 7.9 for these half-reactions.)

Practice Q7. Consider the cell Ag | Ag⁺(0.0010 M) ‖ Ag⁺(0.10 M) | Ag at 25 °C (activities equal to concentrations, ideal salt bridge). Which statements are correct?

  1. The cell potential is about 0.118 V.
  2. Silver dissolves at the left electrode.
  3. If the salt bridge were replaced by a direct junction of the two AgNO₃ solutions, the potential would change, and the change depends on the transport numbers of Ag⁺ and NO₃⁻.
  4. The standard potential of this cell is 0.799 V.

(a) 1, 2 and 3 only (b) 1 and 4 only (c) 2 and 3 only (d) 1, 2, 3 and 4

Answer: (a) 1, 2 and 3 only
  1. Correct. \( E = 0.05916\log(0.10/0.0010) = 0.118 \) V.
  2. Correct. Oxidation (Ag → Ag⁺) at the left, dilute side, raises its concentration towards equality.
  3. Correct. With a direct junction, a junction potential \( (t_+ - t_-)(RT/F)\ln(a_1/a_2) \) is added; the total becomes \( 2t_-(RT/F)\ln(a_{\pm,2}/a_{\pm,1}) \).
  4. Wrong. Both electrodes are the same couple: E° = 0.

Quick Revision Table

IdeaFormula or fact
Cell convention\( E_{\text{cell}} = E_{\text{right}} - E_{\text{left}} \) (both reduction)
Free energy\( \Delta G = -nFE \); \( \Delta G^\circ = -nFE^\circ = -RT\ln K \)
Equilibrium constant\( \log K = nE^\circ/0.05916 \) at 25 °C
Nernst\( E = E^\circ - (0.05916/n)\log Q \)
pH slope\( -0.05916\,m/n \) V per pH
Water window1.229 V wide at every pH
Ksp from E°\( E^\circ_{\text{MX/M}} = E^\circ_{\text{M}^+/\text{M}} + (0.05916/n)\log K_{sp} \)
Combining steps\( E^\circ = \Sigma n_iE^\circ_i/\Sigma n_i \)
Disproportionation\( E^\circ_{\text{right}} > E^\circ_{\text{left}} \) (Cu⁺, H₂O₂)
Entropy, enthalpy\( \Delta S^\circ = nF\,\partial E^\circ/\partial T \); \( \Delta H^\circ = -nF(E^\circ - T\,\partial E^\circ/\partial T) \)
Concentration cellE° = 0; \( E = (0.05916/n)\log(a_2/a_1) \)
Junction (1:1)\( E_j = (t_+ - t_-)(RT/F)\ln(a_1/a_2) \); KCl bridge minimises it
Reference electrodesSHE 0; SCE about +0.241 V; Ag/AgCl (sat. KCl) about +0.197 V
Fuel cell H₂/O₂1.229 V; ΔG°/ΔH° = 0.83

Key Takeaways

What’s Next