Skip to content

Aquatic Chemistry and Water Quality

CSIR NET chemistry: dissolved oxygen, Winkler, BOD and COD, alkalinity, hardness, pE–pH, toxic metals (Hg, Pb, Cd, As, Cr), eutrophication and water treatment.

  • 22 min read
  • Updated
On this page · 17 sections
  1. Prerequisites
  2. The Hook: The Fish Kill After the Bloom
  3. 1. Gases in Water: Dissolved Oxygen
  4. 2. Oxygen Demand: BOD, COD, ThOD
  5. 3. The Carbonate System and Alkalinity
  6. 4. Hardness
  7. 5. Redox Chemistry: pE and pE–pH Diagrams
  8. 6. Toxic Metals and Metalloids
  9. 7. Nutrients and Eutrophication
  10. 8. Water Treatment
  11. Memory Tricks
  12. Don’t Confuse
  13. Common Mistakes
  14. Practice
  15. Quick Revision Table
  16. Key Takeaways
  17. What’s Next

Prerequisites

The Hook: The Fish Kill After the Bloom

1. Gases in Water: Dissolved Oxygen

Gas solubility follows Henry’s law, \( [\text{X}(aq)] = K_H\,p_\text{X} \). For O₂ at 25 °C, \( K_H \approx 1.3 \times 10^{-3} \) mol L⁻¹ atm⁻¹. Air saturated with water vapour (0.0313 atm at 25 °C) has \( p_{\text{O}_2} = 0.2095 \times (1 - 0.0313) = 0.203 \) atm, so

$$[\text{O}_2] = 1.3 \times 10^{-3} \times 0.203 = 2.6 \times 10^{-4} \text{ M} \approx 8.4 \text{ mg L}^{-1}$$

Saturated dissolved oxygen (DO) is only about 8 mg L⁻¹ at 25 °C. It falls with rising temperature (gas solubility decreases as T rises) and with salinity, and it falls with altitude (lower pressure). This small reservoir is why a modest organic load can deoxygenate a river, and why warm-water discharge from power plants (thermal pollution) harms fish twice over: less oxygen dissolves, and warmer fish need more.

Measuring DO: the Winkler method

  1. Add MnSO₄ and alkaline KI (with sodium azide) to a filled, stoppered bottle. White Mn(OH)₂ precipitates.
  2. O₂ oxidises Mn(II) to a brown Mn(IV) oxide-hydroxide: $$2\text{Mn(OH)}_2 + \text{O}_2 \rightarrow 2\text{MnO(OH)}_2$$
  3. Acidify. Mn(IV) oxidises iodide to iodine: $$\text{MnO(OH)}_2 + 4\text{H}^+ + 2\text{I}^- \rightarrow \text{Mn}^{2+} + \text{I}_2 + 3\text{H}_2\text{O}$$
  4. Titrate I₂ with thiosulfate to a starch end point: \( \text{I}_2 + 2\text{S}_2\text{O}_3^{2-} \rightarrow 2\text{I}^- + \text{S}_4\text{O}_6^{2-} \).

Overall: 1 O₂ ≡ 2 MnO(OH)₂ ≡ 2 I₂ ≡ 4 S₂O₃²⁻. Since the equivalent mass of O₂ here is 8 g:

$$\boxed{\text{DO (mg O}_2\text{ L}^{-1}) = \frac{V_{\text{thio}} \times N_{\text{thio}} \times 8000}{V_{\text{sample}}}}$$

The azide modification destroys nitrite, which would otherwise oxidise iodide and give a falsely high DO. Membrane (Clark-type amperometric) and optical (luminescence-quenching) probes are the field alternatives.

2. Oxygen Demand: BOD, COD, ThOD

Organic pollution is measured by how much oxygen it would consume.

MeasureDefinitionOxidisesTime
BOD₅ (biochemical oxygen demand)O₂ consumed by microbes degrading organic matter in the dark at 20 °C over 5 daysonly the biodegradable fraction (and possibly ammonia, unless nitrification is inhibited)5 days
COD (chemical oxygen demand)O₂ equivalent of the acidic dichromate needed to oxidise the samplenearly all organic matter, biodegradable or notabout 2–3 hours
ThOD (theoretical)stoichiometric O₂ to convert a known compound to CO₂ and H₂Ocalculated, not measured
TOC (total organic carbon)carbon content by combustion or UV-persulfate oxidation to CO₂all organic carbonminutes

Typically COD ≥ BOD, because dichromate oxidises compounds microbes cannot (lignin, many synthetic organics) and BOD₅ captures only part of the eventual biological demand. A high COD/BOD ratio flags poorly biodegradable or toxic (microbe-inhibiting) effluent.

BOD by dilution

Polluted water would consume all its DO within hours, so the sample is diluted with aerated, nutrient-and-seed-amended water. DO is measured at the start (D₁) and after 5 days (D₂):

$$\text{BOD}_5 = \frac{D_1 - D_2}{P}$$

where P is the decimal fraction of sample in the bottle (seed corrections are added when seeded dilution water is used).

BOD kinetics

Oxygen consumption is approximately first order in the remaining biodegradable organic matter L:

$$\text{BOD}_t = L_0\left(1 - e^{-kt}\right)$$

where L₀ is the ultimate BOD. With a typical k of about 0.23 day⁻¹ (base e, 20 °C), \( 1 - e^{-1.15} = 0.68 \): BOD₅ is about two-thirds of the ultimate carbonaceous demand.

COD by dichromate reflux

The sample is refluxed with a known excess of K₂Cr₂O₇ in concentrated H₂SO₄ with Ag₂SO₄ (catalyst for oxidising straight-chain aliphatics) and HgSO₄ (complexes chloride, which would otherwise be oxidised to Cl₂ and inflate the COD). Unreacted dichromate is back-titrated with ferrous ammonium sulfate (FAS) using ferroin indicator (blue-green to reddish brown). A blank is run in parallel:

$$\boxed{\text{COD (mg O}_2\text{ L}^{-1}) = \frac{(B - S) \times N_{\text{FAS}} \times 8000}{V_{\text{sample}}}}$$

where B and S are FAS volumes for blank and sample. The blank uses more FAS, because nothing consumed its dichromate.

ThOD

Write the balanced combustion. For glucose:

$$\text{C}_6\text{H}_{12}\text{O}_6 + 6\text{O}_2 \rightarrow 6\text{CO}_2 + 6\text{H}_2\text{O}$$

ThOD = 6 × 32.00/180.16 = 1.066 g O₂ per g glucose. A 300 mg L⁻¹ glucose solution has ThOD = 320 mg L⁻¹. Glucose COD is close to its ThOD; its BOD₅ is lower.

3. The Carbonate System and Alkalinity

Species distribution

Natural waters are buffered by CO₂(aq)/H₂CO₃, HCO₃⁻ and CO₃²⁻ (pKa₁ = 6.35, pKa₂ = 10.33 at 25 °C).

pHDominant speciesFractions (approximate)
< 6.35CO₂(aq)at pH 5.0: 96% CO₂(aq)
6.35CO₂(aq) = HCO₃⁻50 : 50
6.35–10.33HCO₃⁻maximum near pH 8.3, where HCO₃⁻ is about 98%
10.33HCO₃⁻ = CO₃²⁻50 : 50
> 10.33CO₃²⁻at pH 11: 82% CO₃²⁻

HCO₃⁻ peaks at \( \text{pH} = (\text{p}K_{a1} + \text{p}K_{a2})/2 = 8.34 \), which is why the phenolphthalein end point (about pH 8.3) marks the conversion of carbonate to bicarbonate. Most natural fresh waters (pH 6–9) carry their inorganic carbon as bicarbonate.

Alkalinity

Alkalinity is the capacity of water to neutralise strong acid:

$$\text{Alkalinity} = [\text{HCO}_3^-] + 2[\text{CO}_3^{2-}] + [\text{OH}^-] - [\text{H}^+]$$

(plus minor contributions from borate, silicate, phosphate and organic bases). It is reported as mg L⁻¹ CaCO₃. Acidity is the converse, the capacity to neutralise strong base.

Titration with standard acid to two end points:

  • Phenolphthalein alkalinity (P): to about pH 8.3. Neutralises all OH⁻ and converts CO₃²⁻ to HCO₃⁻.
  • Total alkalinity (T): to about pH 4.5 (methyl orange or bromocresol green–methyl red). Converts everything to H₂CO₃.

Assuming OH⁻ and HCO₃⁻ cannot coexist in significant amounts:

ResultOH⁻CO₃²⁻HCO₃⁻
P = 000T
P < T/202PT − 2P
P = T/202P = T0
P > T/22P − T2(T − P)0
P = TT00

Alkalinity and hardness are different quantities: alkalinity is about anions that consume acid; hardness is about divalent cations. Water from a limestone aquifer has both; water softened by sodium ion exchange keeps its alkalinity but loses its hardness.

Ocean acidification in one line

Dissolving more CO₂ raises [H⁺] and converts CO₃²⁻ to HCO₃⁻ (CO₂ + CO₃²⁻ + H₂O → 2HCO₃⁻), lowering the carbonate ion concentration and therefore the saturation state of CaCO₃ that shell-building organisms depend on.

4. Hardness

Hardness is the concentration of polyvalent cations, essentially Ca²⁺ and Mg²⁺, expressed as mg L⁻¹ CaCO₃:

$$\text{Hardness} = [\text{Ca}^{2+}]_{\text{mg/L}} \times \frac{100.09}{40.08} + [\text{Mg}^{2+}]_{\text{mg/L}} \times \frac{100.09}{24.31}$$
TypeCauseRemoval
Temporary (carbonate) hardnessCa²⁺, Mg²⁺ balanced by HCO₃⁻boiling: \( \text{Ca(HCO}_3)_2 \rightarrow \text{CaCO}_3 + \text{H}_2\text{O} + \text{CO}_2 \) (Mg precipitates as Mg(OH)₂ on prolonged boiling); Clark’s process with lime
Permanent (non-carbonate) hardnessCa²⁺, Mg²⁺ balanced by SO₄²⁻, Cl⁻, NO₃⁻not removed by boiling; lime–soda process, ion exchange, zeolites, reverse osmosis

Hard water forms scale (CaCO₃) in boilers and pipes and wastes soap by precipitating calcium and magnesium salts of fatty acids.

EDTA titration

At pH 10 (NH₃/NH₄Cl buffer), with Eriochrome Black T indicator: the Mg–EBT complex is wine red; EDTA, which binds Ca²⁺ and Mg²⁺ more strongly, frees the indicator, which is blue at the end point. Since EDTA reacts 1:1 with each M²⁺:

$$\text{Total hardness (mg CaCO}_3\text{ L}^{-1}) = \frac{V_{\text{EDTA}} \times M_{\text{EDTA}} \times 100.09 \times 1000}{V_{\text{sample}}}$$

Calcium alone is titrated at pH 12–13 (Mg precipitates as Mg(OH)₂) with murexide or calcon-type indicators; magnesium is total minus calcium.

Softening

  • Lime–soda: lime removes carbonate hardness and Mg; soda ash (Na₂CO₃) removes non-carbonate Ca hardness: $$\text{Ca(HCO}_3)_2 + \text{Ca(OH)}_2 \rightarrow 2\text{CaCO}_3 + 2\text{H}_2\text{O}$$ $$\text{CaSO}_4 + \text{Na}_2\text{CO}_3 \rightarrow \text{CaCO}_3 + \text{Na}_2\text{SO}_4$$
  • Ion exchange: cation resin in the Na⁺ form replaces Ca²⁺/Mg²⁺ with Na⁺ (regenerated with brine); H⁺-form cation plus OH⁻-form anion resins in series give demineralised water.
  • Reverse osmosis: pressure above the osmotic pressure pushes water through a semipermeable membrane, leaving salts behind; used for desalination.

5. Redox Chemistry: pE and pE–pH Diagrams

pE

By analogy with pH, pE = −log a(e⁻), the “electron activity”. At 25 °C:

$$\text{pE} = \frac{E}{0.0592}\ (E \text{ in V vs SHE}), \qquad \text{pE}^\circ = \frac{E^\circ}{0.0592}$$

High pE means oxidising conditions (aerated surface water); low pE means reducing (anoxic sediments, waterlogged soils). For Fe³⁺/Fe²⁺, E° = 0.771 V, pE° = 13.0, and \( \text{pE} = 13.0 + \log([\text{Fe}^{3+}]/[\text{Fe}^{2+}]) \).

Stability field of water

$$\text{Upper: } \tfrac{1}{4}\text{O}_2 + \text{H}^+ + \text{e}^- \rightleftharpoons \tfrac{1}{2}\text{H}_2\text{O} \qquad \text{pE} = 20.75 - \text{pH} \ (p_{\text{O}_2} = 1 \text{ atm})$$

$$\text{Lower: } \text{H}^+ + \text{e}^- \rightleftharpoons \tfrac{1}{2}\text{H}_2 \qquad \text{pE} = -\text{pH} \ (p_{\text{H}_2} = 1 \text{ atm})$$

Both lines have slope −1. At pH 7, natural waters lie between pE −7 and +13.75. Any species whose stable form at a given pH lies above or below these lines would oxidise or reduce water itself.

The redox ladder

When oxygen is used up in a lake bottom, a sediment, a waterlogged paddy field or a landfill, microbes use the next-best electron acceptor in a predictable order of decreasing pE:

graph TD
    A[O2 reduction to H2O
aerobic respiration] --> B[NO3- reduction to N2
denitrification] B --> C[MnO2 reduction to Mn2+] C --> D[Fe III oxyhydroxide reduction to Fe2+] D --> E[SO4 2- reduction to H2S] E --> F[CO2 reduction or fermentation to CH4
methanogenesis]

Consequences: anoxic hypolimnia release soluble Fe²⁺ and Mn²⁺ (which precipitate as brown oxides when the water is re-aerated), H₂S (rotten-egg smell, toxic), and CH₄ (paddy fields and wetlands are methane sources). Arsenic adsorbed on iron oxyhydroxides is released when those oxides are reductively dissolved, a key mechanism behind arsenic-rich groundwater in parts of the Bengal delta.

Acid mine drainage

Pyrite exposed by mining oxidises, catalysed by iron-oxidising bacteria:

$$2\text{FeS}_2 + 7\text{O}_2 + 2\text{H}_2\text{O} \rightarrow 2\text{Fe}^{2+} + 4\text{SO}_4^{2-} + 4\text{H}^+$$

Further oxidation of Fe²⁺ and hydrolysis of Fe³⁺ to Fe(OH)₃ (yellow-orange “yellow boy”) releases more acid. Fe³⁺ also oxidises pyrite directly, a self-propagating cycle. The drainage is strongly acidic and dissolves toxic metals from surrounding rock.

6. Toxic Metals and Metalloids

Toxic heavy metals are mostly soft acids that bind soft bases, above all the thiol (–SH) groups of cysteine in enzymes. Their toxicity depends on speciation (oxidation state, organic or inorganic form, complexation), not just on the total amount.

ElementMain forms and sourcesMechanism and effectsNotable episode or fact
HgHg⁰ vapour (chlor-alkali cells, gold mining, coal), Hg²⁺, CH₃Hg⁺Hg²⁺ binds –SH; methylmercury is lipid-soluble, crosses the blood–brain and placental barriers, biomagnifies in fish; neurological damageMinamata disease (Japan, 1950s): methylmercury discharged with factory effluent accumulated in fish and shellfish
Pbold paint, petrol additives (historical), batteries, pipesinhibits haem synthesis enzymes (δ-aminolaevulinic acid dehydratase, ferrochelatase); neurotoxic, especially to children; stored in bonetetraethyllead phased out of petrol
Cdzinc smelting (Cd accompanies Zn), Ni–Cd batteries, phosphate fertilisersbinds metallothionein, accumulates in kidney; renal damage, bone softeningitai-itai disease (Japan): Cd-contaminated irrigation water from mining
Asnatural groundwater (As(III) arsenite, As(V) arsenate), pesticidesAs(III) binds –SH (more toxic); As(V) mimics phosphate and uncouples phosphorylation; skin lesions, cancerswidespread groundwater contamination in West Bengal and Bangladesh
Crelectroplating, tanning, chromate pigmentsCr(VI) (CrO₄²⁻, Cr₂O₇²⁻) is a strong oxidant, crosses cell membranes via sulfate channels, carcinogenic; Cr(III) is much less toxic and poorly absorbedtreat by reducing Cr(VI) to Cr(III) (Fe²⁺, SO₂ or bisulfite) and precipitating Cr(OH)₃

Biomethylation of mercury

Anaerobic bacteria in sediments, using methylcobalamin (a vitamin B₁₂ derivative) as a methyl donor, convert Hg²⁺ to CH₃Hg⁺ and further to volatile (CH₃)₂Hg. The methyl group is transferred as a carbanion equivalent, which suits Hg²⁺ as an electrophile. Methylmercury is the form that concentrates up aquatic food chains.

Other inorganic water pollutants

SpeciesProblem
Fluorideabout 1 mg L⁻¹ protects teeth; higher levels cause dental and then skeletal fluorosis; endemic in parts of India from fluoride-bearing rocks. Defluoridation: the Nalgonda technique (alum plus lime, with adsorption on precipitated Al(OH)₃), activated alumina, reverse osmosis
Nitratereduced to nitrite in infants’ gut; nitrite oxidises haemoglobin Fe(II) to methaemoglobin Fe(III), which cannot carry O₂: methaemoglobinaemia (“blue-baby syndrome”)
Cyanidefrom electroplating and gold extraction; binds cytochrome c oxidase; destroyed by alkaline chlorination to cyanate

Guideline values used for drinking water (WHO values, mg L⁻¹): As 0.01, F⁻ 1.5, NO₃⁻ 50, Pb 0.01, Cd 0.003. National standards (for India, BIS IS 10500) set their own acceptable and permissible limits; quote whichever the question gives.

7. Nutrients and Eutrophication

Eutrophication is nutrient enrichment of a water body leading to excessive growth of algae and plants. In most fresh waters phosphorus is the limiting nutrient; in many coastal waters nitrogen is.

The Redfield ratio describes average phytoplankton composition: C : N : P = 106 : 16 : 1 (by atoms). One phosphorus atom supports 106 carbons of biomass, so a small phosphate input fuels a large bloom, and the bloom’s eventual decay consumes oxygen in proportion to that carbon.

Sources of P: sewage, detergent builders (sodium tripolyphosphate), fertiliser runoff. Detergent history matters: branched alkylbenzene sulfonates (ABS) resisted biodegradation and foamed in rivers; they were replaced by linear alkylbenzene sulfonates (LAS), which bacteria degrade because the straight chain allows β-oxidation from the end. Phosphate builders were then restricted in many countries to curb eutrophication.

8. Water Treatment

Drinking water

graph LR
    A[Raw water] --> B[Screening]
    B --> C[Coagulation and flocculation
alum, ferric salts] C --> D[Sedimentation] D --> E[Filtration
sand] E --> F[Disinfection
Cl2, ClO2, O3, UV] F --> G[Distribution with
residual chlorine]

Coagulation. Natural colloids are negatively charged and stay suspended. Alum, Al₂(SO₄)₃·18H₂O, supplies Al³⁺, which neutralises the charge (high-charge counter-ions are far more effective, the Schulze–Hardy rule) and hydrolyses to a gelatinous Al(OH)₃ floc that sweeps particles down:

$$\text{Al}_2(\text{SO}_4)_3 + 3\text{Ca(HCO}_3)_2 \rightarrow 2\text{Al(OH)}_3 + 3\text{CaSO}_4 + 6\text{CO}_2$$

The reaction consumes alkalinity; lime is added to waters that lack it.

Chlorination. Chlorine hydrolyses:

$$\text{Cl}_2 + \text{H}_2\text{O} \rightarrow \text{HOCl} + \text{H}^+ + \text{Cl}^- \qquad \text{HOCl} \rightleftharpoons \text{H}^+ + \text{OCl}^- \ (\text{p}K_a \approx 7.5)$$

HOCl is a much stronger disinfectant than OCl⁻: being neutral, it penetrates microbial cell walls. Below pH 7.5 HOCl dominates; at pH 8.5 only about 9% of free chlorine is HOCl. Chlorination works best in slightly acidic to neutral water.

Breakpoint chlorination. If the water contains ammonia, chlorine first forms chloramines (NH₂Cl, then NHCl₂, NCl₃): “combined chlorine”, a weaker but longer-lasting disinfectant. Adding more chlorine oxidises the chloramines (largely to N₂), and the residual falls to a minimum, the breakpoint. Beyond it, every extra milligram appears as free chlorine (HOCl + OCl⁻).

graph LR
    A[Cl2 added] --> B[Demand by reductants:
Fe2+, Mn2+, H2S, organics
no residual] B --> C[Chloramines form:
combined residual rises] C --> D[Chloramines destroyed:
residual falls] D --> E[Breakpoint] E --> F[Free residual rises
linearly with dose]

Disinfection by-products. Chlorine reacts with natural humic substances to form trihalomethanes (CHCl₃ and bromine analogues) and haloacetic acids, suspected carcinogens. Remedies: remove organic precursors before chlorination, or use ozone, chlorine dioxide or UV for primary disinfection (keeping a small chlorine or chloramine residual for the pipes). Ozone and UV leave no residual of their own.

Wastewater (sewage) treatment

StageProcessRemoves
Primaryscreening, grit removal, sedimentationsettleable solids; about a third of BOD
Secondarybiological: activated sludge (aerated tank with recycled microbial floc) or trickling filter; then secondary clarifiermost dissolved and colloidal biodegradable organics (BOD)
Tertiary (advanced)P removal by precipitation with Al³⁺, Fe³⁺ or lime (as phosphates); N removal by nitrification then denitrification; filtration, activated carbon, membranesnutrients, refractory organics, remaining solids
Sludgeanaerobic digestionstabilises sludge, produces biogas (CH₄ + CO₂)

Biological nitrogen removal: nitrification (aerobic) \( \text{NH}_4^+ \rightarrow \text{NO}_2^- \rightarrow \text{NO}_3^- \), then denitrification (anoxic, with an organic carbon source) \( \text{NO}_3^- \rightarrow \text{N}_2 \).

Memory Tricks

Don’t Confuse

ThisvsThat
BOD: biological, 5 days, biodegradable onlyCOD: chemical, dichromate, nearly all organics; COD ≥ BOD
Alkalinity: anions that consume acid (HCO₃⁻, CO₃²⁻, OH⁻)hardness: Ca²⁺ + Mg²⁺
Temporary hardness: bicarbonate, removed by boilingpermanent hardness: sulfate/chloride, not removed by boiling
Free chlorine (HOCl + OCl⁻)combined chlorine (chloramines)
Cr(VI): mobile, carcinogenic oxidantCr(III): far less toxic, precipitates as hydroxide
As(III): binds –SH, more toxicAs(V): phosphate analogue
Hg²⁺: inorganic, less mobile in organismsCH₃Hg⁺: lipid-soluble, biomagnifies
Nitrification: NH₄⁺ → NO₃⁻, aerobicdenitrification: NO₃⁻ → N₂, anoxic
ABS detergents: branched, persistentLAS: linear, biodegradable

Common Mistakes

Practice

All questions below are original practice questions written for this page. They are not from any CSIR NET paper.

Level 1: Foundation

  1. Which indicator is used for the EDTA titration of total hardness, and what is the colour change?
  2. Why is HgSO₄ added in the COD test?
  3. Which species of carbon dioxide dominates in water at pH 8.3?
Answers
  1. Eriochrome Black T at pH 10: wine red to blue.
  2. To complex chloride, which would otherwise be oxidised by dichromate and give a falsely high COD.
  3. HCO₃⁻ (about 98% of dissolved inorganic carbon).

Level 2: Part B Style

Practice Q1. In a Winkler titration, 100 mL of a water sample (volume corrected for reagents) needs 3.50 mL of 0.0250 M Na₂S₂O₃. The dissolved oxygen is:

(a) 3.5 mg L⁻¹ (b) 7.0 mg L⁻¹ (c) 14.0 mg L⁻¹ (d) 28.0 mg L⁻¹

Answer: (b) 7.0 mg L⁻¹

Thiosulfate is 1-electron, so 0.0250 M = 0.0250 N. Moles S₂O₃²⁻ = 8.75 × 10⁻⁵; O₂ = 8.75 × 10⁻⁵/4 = 2.19 × 10⁻⁵ mol = 0.700 mg in 100 mL = 7.0 mg L⁻¹. Formula check: 3.50 × 0.0250 × 8000/100 = 7.0. Option (d) forgets the 1:4 ratio; (a) and (c) use 1:2 or 1:8 errors.

Practice Q2. 6.0 mL of wastewater is diluted to 300 mL in a BOD bottle. Initial DO is 8.6 mg L⁻¹ and DO after 5 days at 20 °C is 4.1 mg L⁻¹ (unseeded). The BOD₅ is:

(a) 4.5 mg L⁻¹ (b) 90 mg L⁻¹ (c) 225 mg L⁻¹ (d) 450 mg L⁻¹

Answer: (c) 225 mg L⁻¹

P = 6.0/300 = 0.020. BOD₅ = (8.6 − 4.1)/0.020 = 225 mg L⁻¹. (a) forgets the dilution.

Practice Q3. A water sample of 100 mL needs 3.0 mL of 0.02 N H₂SO₄ to the phenolphthalein end point and a total of 14.0 mL to the methyl orange end point. The alkalinity due to carbonate and bicarbonate (mg L⁻¹ as CaCO₃) is:

(a) CO₃²⁻ 30, HCO₃⁻ 110 (b) CO₃²⁻ 60, HCO₃⁻ 80 (c) CO₃²⁻ 140, HCO₃⁻ 0 (d) OH⁻ 30, CO₃²⁻ 110

Answer: (b)

P = 3.0 × 0.02 × 50 000/100 = 30 mg L⁻¹; T = 14.0 × 0.02 × 50 000/100 = 140 mg L⁻¹ (50 000 = equivalent mass of CaCO₃ in mg). P < T/2 (30 < 70), so CO₃²⁻ = 2P = 60 and HCO₃⁻ = T − 2P = 80; no OH⁻.

Practice Q4. Methylmercury is more hazardous than inorganic Hg²⁺ in aquatic food chains mainly because it:

(a) is a stronger oxidising agent (b) is lipid-soluble, crosses biological membranes and biomagnifies (c) does not bind thiol groups (d) is rapidly excreted by fish

Answer: (b)

CH₃Hg⁺ (usually bound to a thiolate) is lipophilic, crosses the blood–brain and placental barriers, and is retained and concentrated up the food chain. It does bind –SH strongly, so (c) is false; (d) is the opposite of the truth.

Level 3: Part C Style

Practice Q5. For COD, a 20.0 mL effluent sample and a blank are each refluxed with 10.0 mL of 0.25 N K₂Cr₂O₇. Back-titration with 0.100 N FAS needs 24.0 mL for the blank and 14.4 mL for the sample. The same effluent has BOD₅ = 120 mg L⁻¹. Which statements are correct?

  1. The COD is 384 mg L⁻¹.
  2. The COD/BOD₅ ratio suggests a substantial non-biodegradable fraction.
  3. If the sample contained much chloride and HgSO₄ were omitted, the COD would be underestimated.
  4. Ag₂SO₄ is added to catalyse the oxidation of straight-chain aliphatic compounds.

(a) 1, 2 and 4 only (b) 1 and 3 only (c) 2, 3 and 4 only (d) 1, 2, 3 and 4

Answer: (a) 1, 2 and 4 only
  • COD = (24.0 − 14.4) × 0.100 × 8000/20.0 = 384 mg L⁻¹: true.
  • COD/BOD₅ = 3.2. Readily biodegradable wastes (domestic sewage) typically give ratios around 2 or below; 3.2 points to a refractory or inhibitory component: true.
  • Chloride would be oxidised by dichromate, consuming it, so less FAS would be needed and COD would be overestimated: false.
  • True: that is the role of the silver catalyst.

Practice Q6. A BOD test follows \( \text{BOD}_t = L_0(1 - e^{-kt}) \) with k = 0.23 day⁻¹. The measured BOD₅ is 225 mg L⁻¹. Which statements are correct?

  1. The ultimate carbonaceous BOD, L₀, is about 329 mg L⁻¹.
  2. BOD₃ is about 164 mg L⁻¹.
  3. After 5 days about 68% of the ultimate BOD has been exerted.
  4. If the test were run at 30 °C, BOD₅ would be unchanged because L₀ is unchanged.

(a) 1, 2 and 3 only (b) 1 and 4 only (c) 2 and 3 only (d) 1, 2, 3 and 4

Answer: (a) 1, 2 and 3 only
  • \( 1 - e^{-0.23 \times 5} = 1 - e^{-1.15} = 0.683 \); L₀ = 225/0.683 = 329 mg L⁻¹: true.
  • BOD₃ = 329 × (1 − e^{−0.69}) = 329 × 0.498 = 164 mg L⁻¹: true.
  • 0.683 = 68%: true.
  • k increases with temperature (microbial rates are temperature dependent), so more of L₀ is exerted in 5 days; BOD₅ changes even though L₀ does not. That is why the test is standardised at 20 °C: false.

Practice Q7. In a stratified lake at pH 7.0 (25 °C), the surface water has pE = +13 and the bottom water pE = −4. Take pE° = 13.0 for Fe³⁺/Fe²⁺ and the lower water-stability line pE = −pH. Which statements are correct?

  1. The surface water lies within the stability field of water.
  2. At the bottom, sulfate reduction to H₂S is plausible.
  3. In the surface water, [Fe³⁺]/[Fe²⁺] for any iron in solution equals 1, by the Nernst relation at pE = 13.0.
  4. When the lake overturns in autumn, dissolved Fe²⁺ from the bottom will tend to precipitate as iron(III) oxyhydroxide.

(a) 1, 2, 3 and 4 (b) 1, 2 and 4 only (c) 2 and 3 only (d) 1 and 4 only

Answer: (a) 1, 2, 3 and 4
  • At pH 7 the stability field is pE −7 to 13.75; +13 lies inside: true.
  • pE −4 at pH 7 is deep in the reducing range, below the Fe(III)/Fe(II) region and in the sulfate-reducing region of the redox ladder (still above the lower water line at −7): true.
  • pE = pE° + log([Fe³⁺]/[Fe²⁺]) gives log ratio = 13 − 13.0 = 0, ratio 1. (In reality at pH 7 Fe³⁺ precipitates as Fe(OH)₃, which is why dissolved iron in oxic water is so low, but the relation as asked holds): true.
  • Mixing brings O₂ to the Fe²⁺, which is oxidised and hydrolyses to Fe(OH)₃/FeOOH, the brown precipitate seen after overturn: true.

Quick Revision Table

IdeaFact
DO saturationabout 8 mg L⁻¹ at 25 °C; falls with T, salinity, altitude
WinklerMn(OH)₂ → MnO(OH)₂ → I₂ → thiosulfate; O₂ : S₂O₃²⁻ = 1 : 4; azide removes nitrite
DO, BOD, COD formulaV × N × 8000/V_sample (mg O₂ L⁻¹)
BOD₅dark, 20 °C, 5 days; (D₁ − D₂)/P; BOD_t = L₀(1 − e^{−kt})
CODK₂Cr₂O₇/H₂SO₄, Ag₂SO₄ catalyst, HgSO₄ masks Cl⁻, FAS/ferroin back-titration; COD ≥ BOD
CarbonatepKa 6.35, 10.33; HCO₃⁻ max at pH 8.3
AlkalinityHCO₃⁻ + 2CO₃²⁻ + OH⁻ − H⁺; P to 8.3, T to 4.5; P vs T/2 table
Hardnessas CaCO₃; Ca × 2.50, Mg × 4.12; EBT wine red → blue at pH 10
pEE/0.0592; water: 20.75 − pH (upper), −pH (lower)
Redox ladderO₂ > NO₃⁻ > MnO₂ > Fe(III) > SO₄²⁻ > CO₂/CH₄
MetalsHg → CH₃Hg⁺ (Minamata); Cd itai-itai; Pb haem synthesis; As(III) > As(V); Cr(VI) ≫ Cr(III)
NutrientsP limits fresh water; Redfield 106 : 16 : 1; LAS replaced ABS
Coagulationalum → Al(OH)₃ floc; consumes alkalinity
ChlorinationHOCl (pKa ≈ 7.5) ≫ OCl⁻; breakpoint after chloramines; THMs from humics
Sewageprimary (physical), secondary (biological, BOD), tertiary (N, P)

Key Takeaways

What’s Next