Skip to content

Industrial Importance of Main Group Compounds

CSIR NET chemistry: Haber, Ostwald, contact, chlor-alkali and Solvay processes, H2O2, phosphates, silicones, zeolites, boron and halogen compounds in industry.

  • 18 min read
  • Updated
On this page · 21 sections
  1. Prerequisites
  2. The Hook: Bread From Air
  3. Overview of the Big Processes
  4. Ammonia: The Haber–Bosch Process
  5. Nitric Acid: The Ostwald Process
  6. Sulfuric Acid: The Contact Process
  7. Chlor-Alkali Industry
  8. Sodium Carbonate: The Solvay (Ammonia-Soda) Process
  9. Hydrogen Peroxide: The Anthraquinone Process
  10. Phosphorus: Phosphoric Acid and Fertilisers
  11. Silicon Compounds
  12. Boron and Aluminium Compounds
  13. Halogens and Noble Gases
  14. Carbon and Sulfur Compounds
  15. Memory Tricks
  16. Don’t Confuse
  17. Common Mistakes
  18. Practice
  19. Quick Revision Table
  20. Key Takeaways
  21. What’s Next

Prerequisites

The Hook: Bread From Air

Overview of the Big Processes

graph LR
    A[Air: N2] --> H[Haber-Bosch: NH3]
    B[Natural gas: CH4 + H2O] --> H
    H --> O[Ostwald: HNO3]
    H --> U[Urea, ammonium salts]
    H --> SV[Solvay: Na2CO3]
    O --> AN[NH4NO3 fertiliser, explosives]
    S[Sulfur or sulfide ores] --> C[Contact: H2SO4]
    C --> P[Wet process: H3PO4 and superphosphate]
    N[Brine: NaCl] --> CA[Chlor-alkali: NaOH, Cl2, H2]
    N --> SV

Ammonia: The Haber–Bosch Process

$$\text{N}_2(\text{g}) + 3\text{H}_2(\text{g}) \rightleftharpoons 2\text{NH}_3(\text{g}) \qquad \Delta H^\circ \approx -92\ \text{kJ mol}^{-1}$$

(per 2 mol NH₃, that is about −46 kJ per mol of NH₃).

ConditionTypical choiceReason
Pressurehigh (about 150–300 bar)4 mol of gas → 2 mol: high pressure shifts the equilibrium right and increases rate
Temperaturemoderate (about 400–500 °C)the reaction is exothermic, so low temperature favours yield, but the rate is too slow; a compromise
Catalystiron (from magnetite), promoted with K₂O and Al₂O₃ (and CaO)Al₂O₃ is a structural promoter (prevents sintering); K₂O is an electronic promoter (helps N₂ dissociation)
RecyclingNH₃ condensed out, unreacted gas recycledconversion per pass is only partial

The rate-determining step on the catalyst surface is the dissociative adsorption of N₂, because of the very strong N≡N bond. Catalyst poisons include oxygen compounds and sulfur compounds, so the synthesis gas must be purified.

Where the hydrogen comes from: mostly steam reforming of natural gas, \( \text{CH}_4 + \text{H}_2\text{O} \rightarrow \text{CO} + 3\text{H}_2 \), followed by the water-gas shift, \( \text{CO} + \text{H}_2\text{O} \rightarrow \text{CO}_2 + \text{H}_2 \). Nitrogen enters with air in a secondary reformer, where the oxygen is burnt off.

Uses of ammonia: fertilisers (urea, ammonium nitrate, ammonium sulfate, ammonium phosphates), nitric acid, the Solvay process, refrigeration, nylon and other polymers.

Urea: \( 2\text{NH}_3 + \text{CO}_2 \rightarrow \text{NH}_2\text{COONH}_4 \) (ammonium carbamate) \( \rightarrow \text{CO(NH}_2)_2 + \text{H}_2\text{O} \).

Nitric Acid: The Ostwald Process

$$4\text{NH}_3 + 5\text{O}_2 \xrightarrow{\text{Pt–Rh gauze}} 4\text{NO} + 6\text{H}_2\text{O}$$

$$2\text{NO} + \text{O}_2 \rightarrow 2\text{NO}_2$$

$$3\text{NO}_2 + \text{H}_2\text{O} \rightarrow 2\text{HNO}_3 + \text{NO}$$
  • The first step runs at high temperature with a contact time of milliseconds on the gauze, so that NH₃ is oxidised to NO and not to N₂ (the thermodynamically preferred product): the catalyst controls selectivity.
  • The NO formed in the last step is recycled.
  • Distillation gives about 68 % HNO₃ (an azeotrope with water); more concentrated acid needs a dehydrating agent such as concentrated H₂SO₄.

Uses: ammonium nitrate (fertiliser and explosive), nitration (explosives such as TNT, nitroglycerine; dyes; nylon intermediates), metal treatment.

Sulfuric Acid: The Contact Process

$$\text{S} + \text{O}_2 \rightarrow \text{SO}_2 \quad \text{(or roasting of sulfide ores)}$$

$$2\text{SO}_2 + \text{O}_2 \rightleftharpoons 2\text{SO}_3 \qquad \Delta H^\circ \approx -197\ \text{kJ mol}^{-1}$$

$$\text{SO}_3 + \text{H}_2\text{SO}_4 \rightarrow \text{H}_2\text{S}_2\text{O}_7 \ (\text{oleum}) \qquad \text{H}_2\text{S}_2\text{O}_7 + \text{H}_2\text{O} \rightarrow 2\text{H}_2\text{SO}_4$$
ConditionChoiceReason
CatalystV₂O₅ (with K₂SO₄ promoter on silica)cheaper and less easily poisoned than platinum
Temperatureabout 400–450 °C in the beds, with cooling between bedsexothermic: lower T favours SO₃, but the catalyst needs heat to work
Pressureabout 1–2 barconversion is already high; high pressure would cost more than it gains
AbsorptionSO₃ absorbed in 98 % H₂SO₄, not in waterSO₃ + water forms a fine acid mist that is hard to condense
Double contact, double absorptionSO₃ removed between bedsremoving product pushes the remaining SO₂ to react; raises overall conversion and cuts SO₂ emissions

The V₂O₅ catalyst works by a redox cycle: V(V) oxidises SO₂ to SO₃ and is reduced to V(IV), which O₂ reoxidises.

Uses of H₂SO₄: the largest use is phosphate fertilisers (wet-process H₃PO₄ and superphosphate); also ammonium sulfate, petroleum refining, pigments (TiO₂), detergents (sulfonation), lead–acid batteries, metal pickling. It is often called the most produced industrial chemical by mass.

Chlor-Alkali Industry

Electrolysis of concentrated brine:

$$2\text{NaCl} + 2\text{H}_2\text{O} \xrightarrow{\text{electrolysis}} 2\text{NaOH} + \text{Cl}_2 + \text{H}_2$$
  • Anode (oxidation): \( 2\text{Cl}^- \rightarrow \text{Cl}_2 + 2e^- \). Chlorine is evolved rather than O₂, despite O₂ being thermodynamically easier, because of the high overpotential for oxygen evolution on the coated titanium (dimensionally stable) anodes.
  • Cathode (reduction): \( 2\text{H}_2\text{O} + 2e^- \rightarrow \text{H}_2 + 2\text{OH}^- \).
  • The products must be kept apart, or Cl₂ reacts with OH⁻ to give hypochlorite (and chlorate when hot).
CellSeparatorNotes
Membrane cellcation-exchange membrane (perfluorinated sulfonate/carboxylate polymer such as Nafion) passes Na⁺ onlypure, concentrated NaOH; the modern standard
Diaphragm cellporous diaphragm (historically asbestos)NaOH contaminated with NaCl
Mercury cellNa forms an amalgam at a flowing Hg cathode, decomposed separately with watervery pure NaOH, but mercury pollution; being phased out

Uses: NaOH for soap, paper, alumina (Bayer process), textiles, chemicals. Cl₂ for PVC (via vinyl chloride), water treatment, solvents, HCl, titanium production (TiCl₄), bleaches. Bleaching powder is made from Cl₂ and slaked lime (nominally Ca(OCl)Cl); sodium hypochlorite from Cl₂ and cold NaOH.

Sodium Carbonate: The Solvay (Ammonia-Soda) Process

  1. Brine is saturated with NH₃, then carbonated with CO₂: $$\text{NaCl} + \text{NH}_3 + \text{CO}_2 + \text{H}_2\text{O} \rightarrow \text{NaHCO}_3\downarrow + \text{NH}_4\text{Cl}$$
  2. NaHCO₃, the least soluble salt present, precipitates and is calcined: $$2\text{NaHCO}_3 \rightarrow \text{Na}_2\text{CO}_3 + \text{CO}_2 + \text{H}_2\text{O}$$
  3. CO₂ comes from limestone: \( \text{CaCO}_3 \rightarrow \text{CaO} + \text{CO}_2 \), plus the CO₂ from step 2.
  4. Ammonia is recovered with the lime: \( 2\text{NH}_4\text{Cl} + \text{Ca(OH)}_2 \rightarrow 2\text{NH}_3 + \text{CaCl}_2 + 2\text{H}_2\text{O} \).
$$\boxed{\text{Net: } \text{CaCO}_3 + 2\text{NaCl} \rightarrow \text{Na}_2\text{CO}_3 + \text{CaCl}_2}$$

Ammonia is a recycled reagent, not consumed; CaCl₂ is the main by-product. This net reaction is not spontaneous as written in aqueous solution; it works because the steps exploit the low solubility of NaHCO₃.

Uses of Na₂CO₃ (soda ash): glass manufacture (the largest use), detergents, water softening, paper, chemicals. NaHCO₃: baking soda, antacid, fire extinguishers.

Hydrogen Peroxide: The Anthraquinone Process

$$\text{2-alkylanthraquinol} + \text{O}_2 \rightarrow \text{2-alkylanthraquinone} + \text{H}_2\text{O}_2$$

$$\text{2-alkylanthraquinone} + \text{H}_2 \xrightarrow{\text{Pd}} \text{2-alkylanthraquinol}$$

Net: \( \text{H}_2 + \text{O}_2 \rightarrow \text{H}_2\text{O}_2 \), with the anthraquinone as a recycled hydrogen carrier. The H₂O₂ is extracted into water and concentrated by distillation.

Uses: bleaching of paper pulp and textiles (a chlorine-free alternative), wastewater treatment, synthesis of peroxo compounds (sodium perborate and percarbonate in detergents), propylene oxide manufacture, and as a “green” oxidant because its by-product is water.

Phosphorus: Phosphoric Acid and Fertilisers

Wet process (most phosphoric acid):

$$\text{Ca}_3(\text{PO}_4)_2 + 3\text{H}_2\text{SO}_4 \rightarrow 2\text{H}_3\text{PO}_4 + 3\text{CaSO}_4$$

(the real rock is fluorapatite, Ca₅(PO₄)₃F, and the by-product is gypsum, with HF/H₂SiF₆). The acid is impure but suitable for fertilisers.

Thermal (furnace) process (pure acid via elemental P):

$$2\text{Ca}_3(\text{PO}_4)_2 + 6\text{SiO}_2 + 10\text{C} \rightarrow 6\text{CaSiO}_3 + \text{P}_4 + 10\text{CO}$$

P₄ is burnt to P₄O₁₀ and hydrated to pure H₃PO₄ for food, pharmaceutical and detergent uses.

Fertilisers:

ProductMade fromMain phosphorus compound
Single superphosphatephosphate rock + H₂SO₄Ca(H₂PO₄)₂ mixed with CaSO₄
Triple superphosphatephosphate rock + H₃PO₄: \( \text{Ca}_3(\text{PO}_4)_2 + 4\text{H}_3\text{PO}_4 \rightarrow 3\text{Ca(H}_2\text{PO}_4)_2 \)Ca(H₂PO₄)₂ without gypsum dilution
Ammonium phosphates (MAP, DAP)NH₃ + H₃PO₄NH₄H₂PO₄, (NH₄)₂HPO₄

Fertiliser grades are expressed as % “P₂O₅” by convention, even though no P₂O₅ is present: the conversion makes different phosphates comparable.

Other phosphates: sodium tripolyphosphate, Na₅P₃O₁₀, was widely used as a detergent builder (it sequesters Ca²⁺ and Mg²⁺); phosphate run-off contributes to eutrophication of lakes, which led many countries to limit it. P₄S₃ in matches; organophosphates as pesticides and flame-retardants.

Silicon Compounds

MaterialProduction / compositionUses
Silicon (metallurgical grade)\( \text{SiO}_2 + 2\text{C} \rightarrow \text{Si} + 2\text{CO} \) in an electric arc furnacealuminium and steel alloys, silicones (Rochow process)
Silicon (electronic grade)Si → SiHCl₃ (with HCl), purified by distillation, decomposed on hot Si rods with H₂ (Siemens process); single crystals then grownsemiconductors, solar cells
SiliconesRochow process + hydrolysis (see Groups 14 and 15)sealants, lubricants, water repellents, insulation, medical implants, cosmetics
Glasssoda-lime glass from sand, Na₂CO₃ and CaCO₃; borosilicate glass adds B₂O₃containers, windows; borosilicate for heat-resistant labware
Portland cementlimestone + clay heated in a kiln to clinker, ground with a little gypsummain phases: tricalcium silicate, dicalcium silicate, tricalcium aluminate, tetracalcium aluminoferrite; setting is hydration to calcium silicate hydrate
Silica gelfrom sodium silicate + acid, drieddesiccant, chromatography
SiCSiO₂ + C in an electric furnace (Acheson process)abrasive, refractory, power electronics

Zeolites

Zeolites are crystalline aluminosilicates with open 3D frameworks of corner-sharing SiO₄ and AlO₄ tetrahedra enclosing cages and channels of molecular size. General formula:

$$\text{M}_{x/n}[(\text{AlO}_2)_x(\text{SiO}_2)_y] \cdot z\text{H}_2\text{O}$$
  • Each Al in the framework carries one negative charge, balanced by exchangeable cations \( \text{M}^{n+} \).
  • Löwenstein’s rule: Al–O–Al linkages are avoided, so Si/Al ≥ 1.
  • Zeolite A (Si/Al = 1) has the composition Na₁₂[(AlO₂)₁₂(SiO₂)₁₂]·27H₂O.
UseProperty used
Detergent builders, water softeningion exchange: Na⁺ out, Ca²⁺ and Mg²⁺ in
Molecular sieves (drying gases and solvents, separating N₂/O₂, linear/branched alkanes)uniform pore size
Catalytic cracking in refining; ZSM-5 for shape-selective reactions (methanol to gasoline, xylene isomerisation)acidic H⁺ forms (Brønsted acid sites) plus shape selectivity

Boron and Aluminium Compounds

CompoundUse
Borax, boric acidborosilicate glass, glass fibre, enamels, fluxes for welding and soldering, antiseptic, fire retardants, buffer
Sodium perborateoxygen bleach in detergents
NaBH₄selective reducing agent; bleaching of wood pulp (via dithionite generation)
Boron nitridehigh-temperature lubricant, crucibles, c-BN abrasives
Boron carbide, B₄Cabrasive, armour, neutron absorber (¹⁰B captures neutrons) in nuclear reactors
Alumina, Al₂O₃Bayer process: bauxite digested in hot NaOH, Al(OH)₃ precipitated and calcined; feed for aluminium metal, catalyst supports, abrasives (corundum)
Aluminium metalHall–Héroult: Al₂O₃ dissolved in molten cryolite (Na₃AlF₆), electrolysed with carbon anodes (which are consumed as CO₂)
Alums, Al₂(SO₄)₃coagulants in water treatment (Al(OH)₃ flocs), paper sizing, mordants
AlCl₃Friedel–Crafts catalyst
Alkylaluminiums (AlEt₃)co-catalyst in Ziegler–Natta polymerisation of alkenes

Halogens and Noble Gases

CompoundProductionUse
F₂electrolysis of KF dissolved in anhydrous HF (KF·2HF melt)UF₆ for uranium enrichment, SF₆, fluoropolymers
HF\( \text{CaF}_2 + \text{H}_2\text{SO}_4 \rightarrow \text{CaSO}_4 + 2\text{HF} \) (fluorspar)fluorocarbons, PTFE, cryolite and AlF₃ for aluminium, glass etching
Br₂oxidation of bromide in brines with Cl₂ (\( \text{Cl}_2 + 2\text{Br}^- \rightarrow 2\text{Cl}^- + \text{Br}_2 \))flame retardants, drilling fluids (CaBr₂), pharmaceuticals
I₂from brines or as a by-product of nitrate deposits (iodate reduced to iodine)antiseptics, iodised salt (as KI or KIO₃), X-ray contrast media, catalysts
ClO₂reduction of NaClO₃ on siteelemental-chlorine-free pulp bleaching, water treatment
Noble gasesfractional distillation of liquid air (He from natural gas)He: cryogenics (superconducting magnets), balloons, breathing mixtures; Ar: inert atmosphere for welding and metallurgy, lamps; Ne: signs; Xe: lamps, anaesthesia; XeF₂ as a fluorinating agent

Carbon and Sulfur Compounds

  • Activated carbon: adsorbent for water purification, gas masks, decolourising sugar solutions.
  • Carbon black: reinforcing filler for rubber tyres, pigment.
  • Graphite: electrodes (steel arc furnaces, aluminium smelting), lubricants, battery anodes.
  • Synthesis gas (CO + H₂): methanol synthesis, Fischer–Tropsch fuels, hydroformylation.
  • CS₂: viscose rayon and cellophane manufacture.
  • Sulfur: vulcanisation of rubber (sulfur cross-links between polymer chains), fungicides, H₂SO₄.
  • Sodium thiosulfate: photographic fixer, dechlorination of water.

Memory Tricks

Don’t Confuse

ThisvsThat
Haber catalyst: promoted FeOstwald: Pt–Rh gauze; contact: V₂O₅
SO₃ absorbed in H₂SO₄ (oleum)SO₃ in water: acid mist
Solvay makes Na₂CO₃, not K₂CO₃KHCO₃ too soluble to precipitate
Wet-process H₃PO₄ (impure, fertiliser)thermal-process H₃PO₄ via P₄ (pure, food grade)
Single superphosphate (with CaSO₄)triple superphosphate (no gypsum dilution)
Bayer process: purifies aluminaHall–Héroult: electrolyses alumina to Al
Membrane cell: Na⁺-selective membranemercury cell: Na amalgam
Anthraquinone process: H₂O₂Raschig process: N₂H₄
Zeolites: crystalline, uniform poressilica gel: amorphous, broad pore distribution

Common Mistakes

Practice

All questions below are original practice questions written for this page. They are not from any CSIR NET paper.

Level 1: Foundation

  1. Name the catalyst used in the contact process.
  2. What is the main by-product of the Solvay process?
  3. In the membrane chlor-alkali cell, which ion crosses the membrane?
Answers
  1. V₂O₅ (vanadium(V) oxide, promoted with K₂SO₄).
  2. CaCl₂.
  3. Na⁺, from the anode compartment to the cathode compartment.

Level 2: Part B Style

Practice Q1. In the Haber process, the role of Al₂O₃ in the iron catalyst is mainly to:

(a) increase the equilibrium constant (b) act as a structural promoter preventing sintering of the iron (c) oxidise N₂ (d) absorb ammonia

Answer: (b)

Al₂O₃ keeps the iron crystallites small and stable (structural promoter); K₂O is the electronic promoter. No catalyst or promoter changes an equilibrium constant.

Practice Q2. Which statement about the contact process is incorrect?

(a) SO₂ is oxidised to SO₃ over V₂O₅. (b) SO₃ is absorbed in concentrated H₂SO₄ to give oleum. (c) Very high pressures (several hundred bar) are used to drive the equilibrium. (d) The reaction 2SO₂ + O₂ → 2SO₃ is exothermic.

Answer: (c)

The contact process runs near 1–2 bar: conversion is already high at moderate temperature with the catalyst and double absorption, so high-pressure plant is not worth the cost. (a), (b) and (d) are correct.

Practice Q3. In the Ostwald process the platinum–rhodium catalyst is essential because:

(a) without it NH₃ does not react with O₂ at all (b) it makes NO the main product instead of N₂, which is thermodynamically favoured (c) it converts NO directly to HNO₃ (d) it lowers the enthalpy of reaction

Answer: (b)

NH₃ burns in O₂ to N₂ and H₂O without a catalyst. The Pt–Rh gauze with millisecond contact times gives NO selectively. Catalysts never change \( \Delta H \).

Practice Q4. A zeolite has the framework composition [(AlO₂)₁₂(SiO₂)₁₂]. The number of monovalent cations needed per formula unit for charge balance is:

(a) 6 (b) 12 (c) 24 (d) 0

Answer: (b) 12

Each AlO₂ unit in the framework carries a charge of −1 (Al³⁺ with two O²⁻ shared: \( 3 - 4 = -1 \)); SiO₂ units are neutral. 12 Al → −12, balanced by 12 Na⁺: this is zeolite A, Na₁₂[(AlO₂)₁₂(SiO₂)₁₂]·27H₂O.

Level 3: Part C Style

Practice Q5. A chlor-alkali membrane cell runs at 1.00 × 10⁵ A for 24.0 h with 95.0 % current efficiency. Which pair (mass of Cl₂, mass of NaOH) is closest to the daily production? (F = 96 485 C mol⁻¹; Cl₂ = 70.90, NaOH = 40.00 g mol⁻¹)

(a) 3.02 t Cl₂, 3.40 t NaOH (b) 3.17 t Cl₂, 3.58 t NaOH (c) 6.03 t Cl₂, 3.40 t NaOH (d) 1.51 t Cl₂, 1.70 t NaOH

Answer: (a)

Charge used \( = 1.00 \times 10^5 \times 24.0 \times 3600 \times 0.950 = 8.208 \times 10^9 \) C.

Moles of electrons \( = 8.208 \times 10^9/96\,485 = 8.507 \times 10^4 \) mol.

  • Cl₂: 2 e⁻ per molecule → \( 4.254 \times 10^4 \) mol × 70.90 g = \( 3.02 \times 10^6 \) g = 3.02 t.
  • NaOH: 1 e⁻ per OH⁻ → \( 8.507 \times 10^4 \) mol × 40.00 g = 3.40 t.

(b) ignores the current efficiency; (c) forgets that Cl₂ needs 2 electrons; (d) halves both.

Practice Q6. In a contact plant, 1.00 t of sulfur is converted to H₂SO₄ with an overall efficiency of 96.0 %. The mass of 98.0 % (by mass) sulfuric acid produced is closest to: (S = 32.06, H₂SO₄ = 98.08 g mol⁻¹)

(a) 2.94 t (b) 3.00 t (c) 3.06 t (d) 2.88 t

Answer: (b) 3.00 t

Moles S \( = 1.00 \times 10^6/32.06 = 3.119 \times 10^4 \) mol. Each S gives one H₂SO₄.

Pure H₂SO₄ \( = 3.119 \times 10^4 \times 0.960 \times 98.08 = 2.937 \times 10^6 \) g = 2.94 t.

As 98.0 % acid: \( 2.937/0.980 = 3.00 \) t.

(a) is pure H₂SO₄ (forgets the 98 % dilution); (c) is 100 % efficiency as pure acid (3.06 t); (d) applies the 0.98 factor the wrong way (2.94 × 0.98).

Practice Q7. Consider the following statements about industrial main group chemistry:

  1. In the Solvay process, 1.00 t of NaCl used with 75 % efficiency gives about 0.68 t of Na₂CO₃.
  2. Pure Ca(H₂PO₄)₂ corresponds to about 60.6 % “P₂O₅”.
  3. One gram of hydrated zeolite A, Na₁₂[(AlO₂)₁₂(SiO₂)₁₂]·27H₂O (M about 2191 g mol⁻¹), can take up at most about 2.7 mmol of Ca²⁺ by complete exchange.
  4. In the anthraquinone process the anthraquinone is consumed and must be replaced each cycle.

Which are correct? (NaCl = 58.44, Na₂CO₃ = 105.99, Ca(H₂PO₄)₂ = 234.05, P₂O₅ = 141.94 g mol⁻¹)

(a) 1, 2 and 3 only (b) 1 and 4 only (c) 2, 3 and 4 only (d) 1, 2, 3 and 4

Answer: (a) 1, 2 and 3 only
  1. Correct. \( 10^6/58.44 = 1.711 \times 10^4 \) mol NaCl; × 0.75 = \( 1.283 \times 10^4 \) mol; ÷ 2 = \( 6.42 \times 10^3 \) mol Na₂CO₃ × 105.99 = \( 6.80 \times 10^5 \) g = 0.68 t.
  2. Correct. One Ca(H₂PO₄)₂ contains 2 P, equivalent to one P₂O₅: \( 141.94/234.05 = 60.6 \) %.
  3. Correct. 12 Na⁺ exchange for 6 Ca²⁺ per formula unit: \( 6/2191 = 2.74 \times 10^{-3} \) mol g⁻¹ = 2.7 mmol g⁻¹ (about 110 mg Ca²⁺ per g).
  4. Wrong. The anthraquinone is a recycled hydrogen carrier; the net reaction is H₂ + O₂ → H₂O₂.

Quick Revision Table

Process / materialKey facts
Haber–BoschN₂ + 3H₂ ⇌ 2NH₃, ΔH° ≈ −92 kJ; promoted Fe (K₂O, Al₂O₃); 400–500 °C, 150–300 bar; N₂ dissociation rate-limiting
UreaNH₃ + CO₂ → ammonium carbamate → urea
OstwaldNH₃ → NO (Pt–Rh, ms contact) → NO₂ → HNO₃; NO recycled; 68 % azeotrope
ContactV₂O₅, 400–450 °C, 1–2 bar; ΔH° ≈ −197 kJ; SO₃ into H₂SO₄ (oleum); double absorption
Chlor-alkali2NaCl + 2H₂O → 2NaOH + Cl₂ + H₂; membrane (Na⁺), diaphragm, mercury cells; Cl₂ by O₂ overpotential
SolvayNaHCO₃ precipitates; NH₃ recycled; net CaCO₃ + 2NaCl → Na₂CO₃ + CaCl₂; not for K₂CO₃
H₂O₂anthraquinone autoxidation; Pd hydrogenation; net H₂ + O₂
H₃PO₄wet (rock + H₂SO₄, gypsum) or thermal (via P₄)
FertilisersSSP Ca(H₂PO₄)₂ + CaSO₄; TSP Ca(H₂PO₄)₂; MAP/DAP; grade as % P₂O₅
Siliconarc furnace (metallurgical), Siemens SiHCl₃ (electronic)
ZeolitesM\(_{x/n}\)[(AlO₂)ₓ(SiO₂)ᵧ]·zH₂O; one charge per Al; Löwenstein; ion exchange, sieves, cracking (ZSM-5)
AluminiumBayer (NaOH digestion of bauxite) + Hall–Héroult (Al₂O₃ in cryolite)
FluorineF₂ from KF·2HF electrolysis; HF from CaF₂ + H₂SO₄; UF₆

Key Takeaways

What’s Next

Advertisement
Advertisement