Weather Hazards at Take-off, Cruise and Landing
CSIR NET Part C aviation meteorology: altimetry, density altitude, runway wind components, thunderstorms, jet streams and hazards by phase of flight.
- 25 min
On this page · 16 sections
- Prerequisites
- The Hook: One Aircraft, One Day, Three Kinds of Weather
- Why Weather Matters Differently in Each Phase
- Altimetry: Where the Aircraft Thinks It Is
- Air Density and Aircraft Performance
- Wind and the Runway
- Hazards Phase by Phase
- Thunderstorms: The All-Phase Hazard
- Information for Aviation
- Memory Tricks
- Don’t Confuse
- Common Mistakes
- Practice
- Quick Revision Table
- Key Takeaways
- What’s Next
Prerequisites
- The International Standard Atmosphere, hydrostatic balance and the hypsometric equation, from Composition, Thermal Structure, Hydrostatics and the Standard Atmosphere.
- Parcel buoyancy, CAPE and how deep convection grows, from Vertical Stability and Tropical Convection.
- Jet streams and the monsoon circulation, from Air Masses, Monsoon, Jet Streams, Cyclones and ENSO.
- Cloud types and precipitation processes, from Clouds, Precipitation and General Circulation.
The Hook: One Aircraft, One Day, Three Kinds of Weather
Why Weather Matters Differently in Each Phase
An aircraft flies on airspeed (speed relative to the air), not ground speed, and its lift depends on air density:
$$\boxed{L = \tfrac{1}{2}\,\rho\,V^2\,S\,C_L}$$where \( \rho \) is air density, \( V \) the true airspeed, \( S \) the wing area and \( C_L \) the lift coefficient. Two consequences run through this whole chapter:
- Anything that lowers density (heat, altitude, humidity) forces a higher true airspeed for the same lift, so take-off and landing distances grow and climb performance falls.
- Anything that suddenly changes the wind along the flight path changes the airspeed by the same amount at that instant. Near the ground, where airspeed margins are small, a sudden loss of headwind is dangerous.
The phases differ in how close the aircraft is to the ground and how much margin it has:
| Phase | Height and speed | Margin | Dominant weather hazards |
|---|---|---|---|
| Take-off and initial climb | Near ground, low speed, high power | Small: little height, speed near minimum | Density altitude, crosswind and tailwind, wind shear and microbursts, low visibility, thunderstorms, ground icing (frost, snow) |
| Climb and descent | Passing through all cloud layers | Moderate | Airframe icing in middle-level cloud, convective turbulence, embedded cumulonimbus |
| Cruise | Upper troposphere or lower stratosphere, high speed | Large in height, narrow in speed at high altitude | Clear-air turbulence near jet streams and tropopause, mountain waves, deep convection, volcanic ash, ice crystals near storm tops, jet-stream headwinds |
| Approach and landing | Descending on a fixed path, low speed, low power | Smallest: committed to a path near the ground | Low ceiling and visibility (fog, low stratus, heavy rain), wind shear, gusts and crosswind, contaminated runway, thunderstorms |
graph LR
A["Take-off
density altitude,
crosswind, shear,
fog, frost"] --> B["Climb
icing, convective
turbulence"]
B --> C["Cruise
CAT, jet streams,
mountain waves,
CB tops, volcanic ash"]
C --> D["Descent
icing, embedded CB"]
D --> E["Approach and landing
low ceiling and visibility,
wind shear, gusts,
wet runway"]Thunderstorms are the only hazard that appears in every column, which is why they get their own section below.
Altimetry: Where the Aircraft Thinks It Is
The pressure altimeter
A pressure altimeter is an aneroid barometer calibrated in height using the International Standard Atmosphere (ISA): 15 °C and 1013.25 hPa at mean sea level, lapse rate 6.5 K km\(^{-1}\) up to 11 km, isothermal above to 20 km. It converts the measured static pressure into the height that pressure would have in the ISA, measured from a reference pressure set by the pilot on the subscale.
Near sea level the ISA gives
$$\frac{dz}{dp} = -\frac{R_d T}{g\,p} = -\frac{287.05 \times 288.15}{9.807 \times 101325}\ \mathrm{m\,Pa^{-1}} \approx -8.3\ \mathrm{m\,hPa^{-1}}$$so 1 hPa corresponds to about 8.3 m (about 27 ft) near sea level. The figure grows with height because air thins.
The three settings
| Setting | Definition | Altimeter reads on the ground | Used for |
|---|---|---|---|
| QFE | Pressure at aerodrome elevation (or runway threshold) | Zero | Height above the aerodrome |
| QNH | QFE reduced to mean sea level using the ISA | Aerodrome elevation | Altitude above MSL near the ground and terrain clearance |
| Standard (1013.25 hPa) | Fixed, the same for every aircraft | Pressure altitude | Flight levels in cruise: FL350 is a pressure altitude of 35,000 ft |
Below a transition altitude pilots fly on QNH; above it they fly flight levels on 1013.25 hPa. The values depend on the country and aerodrome. Everyone at cruise uses the same setting, so the vertical separation between two aircraft stays correct even if the actual sea-level pressure varies: both altimeters err by the same amount.
Altimeter errors from pressure and temperature
Pressure error. If an aircraft flies from a high-pressure region to a low-pressure region without resetting QNH, each pressure surface lies lower in the low, so the altimeter reads high: the aircraft is lower than indicated. Flying from QNH 1020 hPa into an area of QNH 1000 hPa without resetting gives an error of about 20 × 8.3 ≈ 166 m. Pilots remember this as “high to low, look out below.”
Temperature error. By the hypsometric equation the thickness between two pressure levels is proportional to the layer-mean (virtual) temperature:
$$\Delta z = \frac{R_d \bar T_v}{g}\ln\frac{p_1}{p_2}$$The altimeter assumes ISA temperatures. In air colder than ISA the layer is thinner, so a given pressure drop is reached at a smaller real height: the true altitude is below the indicated altitude. To first order,
$$z_\text{true} \approx z_\text{indicated} \times \frac{\bar T_\text{actual}}{\bar T_\text{ISA}}$$with heights measured from the setting’s reference level and temperatures in kelvin. The error grows with height above the station, so it matters most for obstacle clearance on instrument approaches in very cold weather. “Cold to cold” is the same rule as “high to low”: both put you below where you think you are.
Air Density and Aircraft Performance
Pressure altitude and density altitude
- Pressure altitude (PA): the altitude in the ISA at which the observed pressure occurs. Near sea level, PA ≈ elevation + (1013.25 − QNH) × 8.3 m.
- Density altitude (DA): the altitude in the ISA at which the observed density occurs. It is the altitude the aircraft “feels”: engines, propellers and wings respond to density.
When the temperature is above ISA, density is lower than standard and DA is higher than PA. A widely used rule of thumb is that DA rises by about 120 ft (about 36 m) for each kelvin above the ISA temperature at that pressure altitude. It is an approximation; compute from the gas law when the numbers matter.
$$\rho = \frac{p}{R_d T_v}, \qquad T_v \approx T(1 + 0.61 q)$$Humid air is less dense than dry air at the same pressure and temperature, because water vapour (molar mass 18) replaces nitrogen and oxygen (about 29). The effect is smaller than that of temperature but adds to it on hot, humid monsoon days.
What low density does
| Effect | Why |
|---|---|
| Longer take-off and landing roll | Higher true airspeed needed for the same lift; lower thrust |
| Reduced climb gradient | Less excess thrust; matters for obstacle clearance after take-off |
| Payload restrictions | Maximum take-off weight falls on hot afternoons at high or hot aerodromes |
| Lower ceiling in cruise | The margin between stall speed and maximum speed narrows at high altitude and high temperature |
Hot afternoons at elevated aerodromes are a classic case of reduced performance, and the heat of the north Indian pre-monsoon season adds to it. Airlines often schedule heavy departures in the cooler early morning for this reason.
Wind and the Runway
Wind components
Aircraft take off and land into wind whenever possible: a headwind reduces the ground speed needed to reach flying airspeed, shortening the runway required. Runway numbers give the magnetic heading in tens of degrees (runway 27 points about 270° magnetic). For a wind of speed \( V \) blowing from a direction making angle \( \theta \) with the runway heading:
$$\boxed{\text{headwind} = V\cos\theta, \qquad \text{crosswind} = V\sin\theta}$$A negative headwind component is a tailwind. Each aircraft type has a maximum demonstrated crosswind and a tailwind limit.
Gusts and gust factor
Reported winds include gusts (for example 25015G28KT: from 250° at 15 kt gusting 28 kt). Gusts arise from turbulent mixing of faster air down from aloft (stronger in an unstable, daytime boundary layer), from convective outflows, and from flow around buildings and terrain. On approach, crews commonly add part of the gust increment to the target airspeed, so that a sudden lull does not leave the aircraft too slow. Strong gusty winds are also a source of mechanical turbulence near the ground, treated on the icing and turbulence page.
Wind at cruise: the jet streams
At cruise, wind changes ground speed and therefore fuel and time. Ground speed = true airspeed ± wind component along track. A 480 kt aircraft with a 120 kt headwind makes 360 kt over the ground; a 1,800 nautical-mile sector takes 5 h against the wind and 3 h with the same wind behind it.
Over India the relevant jets are:
| Jet | Level and latitude | Season | Aviation relevance |
|---|---|---|---|
| Subtropical westerly jet (STJ) | Upper troposphere (around 200 hPa) near 25–35° N | Winter, lying over north India; shifts north of the Himalaya in summer | Large tailwinds eastbound, headwinds westbound; CAT near the core |
| Tropical easterly jet (TEJ) | Upper troposphere (around 100–150 hPa) over the peninsula | Summer monsoon | Easterly component on routes across south India; associated with monsoon convection |
| Somali / low-level jet | Lower troposphere (around 850 hPa) over the Arabian Sea | Summer monsoon | Strong low-level winds and shear over the west coast |
The physics (thermal wind balance, the meridional temperature gradient) is in Air Masses, Monsoon, Jet Streams, Cyclones and ENSO. Clear-air turbulence near jets is treated on the next page.
Hazards Phase by Phase
Take-off and initial climb
- Density altitude: as above. Heat, elevation and humidity all reduce performance.
- Crosswind, tailwind and gusts: limit which runway can be used and add handling load.
- Low-level wind shear and microbursts: the most dangerous single hazard in the first few hundred metres of climb; see Visibility and Wind Shear.
- Low visibility: fog and low cloud set take-off minima; a departure may also need a nearby alternate aerodrome that is above landing minima in case the aircraft must return.
- Ground icing: frost, snow and freezing precipitation on wings must be removed before take-off; even a thin roughness layer of frost reduces maximum lift and raises stall speed. This is the clean aircraft principle.
- Heavy rain and contaminated runways: standing water lengthens the take-off roll (spray drag) and reduces braking for a rejected take-off.
- Thunderstorms near the aerodrome: gust fronts, microbursts, lightning and hail; ground operations such as refuelling may be suspended when lightning is close.
Cruise
- Clear-air turbulence (CAT): in cloud-free air near jet streams and the tropopause where vertical wind shear is strong; invisible to weather radar because there are no hydrometeors.
- Mountain waves: downstream of ridges in stable flow; strong up- and downdrafts and rotor turbulence.
- Deep convection: cumulonimbus tops can reach and overshoot the tropopause, well above typical cruise levels in the tropics. Embedded storms in widespread cloud (monsoon troughs, the ITCZ, tropical cyclones) are hard to see.
- High ice-water content near storm tops: dense concentrations of small ice crystals can cause engine power loss and probe icing. They give only weak radar echoes, so they can be present where radar shows little.
- Volcanic ash: silicate ash melts in the hot section of jet engines and can cause loss of thrust, as well as abrading windscreens and blocking pitot tubes. Ash is poorly detected by weather radar; it is tracked from satellites and dispersion models by Volcanic Ash Advisory Centres.
- Temperature at altitude: temperatures warmer than ISA reduce the maximum altitude and engine thrust.
- Jet-stream winds: a performance and planning factor more than a hazard.
Approach and landing
- Low ceiling and visibility: fog, low stratus, heavy rain, dust and haze. Each approach type has minima for decision height (or minimum descent altitude) and runway visual range; below them the crew must go around or divert.
- Wind shear and microbursts: an aircraft on a 3° glide path with low power and speed has little margin; loss of headwind makes it sink below the path.
- Crosswind and gusts: strongest handling load at touchdown; gusty winds over buildings and terrain near the threshold add mechanical turbulence.
- Wet or contaminated runway: reduced braking; heavy rain can cause aquaplaning when a film of water separates the tyre from the surface.
- Sea-breeze and land-breeze shifts: at coastal aerodromes the wind can reverse within an hour, changing the runway in use and producing shear along the sea-breeze front.
Thunderstorms: The All-Phase Hazard
Life cycle
The US Thunderstorm Project of the late 1940s described the single-cell storm in three stages:
| Stage | Vertical motion | Precipitation | Aviation note |
|---|---|---|---|
| Cumulus (developing) | Updraft throughout the cell | Forming aloft, not yet at the ground | Strong updrafts and turbulence; icing above the freezing level |
| Mature | Updraft and downdraft side by side | Reaches the ground; onset of heavy rain marks this stage | Every hazard at its peak: severe turbulence, hail, lightning, microbursts, gust front |
| Dissipating | Downdraft dominates | Light, stratiform rain | Residual downdrafts and outflow; anvil may persist |
A single ordinary cell typically lasts about an hour or less, but multicell clusters, squall lines and supercells last for hours because new cells keep forming along the outflow or the updraft is sustained by vertical wind shear.
The hazards packaged in one cloud
graph TD
CB["Mature cumulonimbus"] --> T["Turbulence
severe to extreme
inside and near the cloud"]
CB --> I["Icing
supercooled water
carried up by updrafts"]
CB --> H["Hail
inside, below and
even outside under the anvil"]
CB --> L["Lightning
strikes to aircraft;
static, radio noise"]
CB --> D["Downbursts
microbursts and
low-level wind shear"]
CB --> G["Gust front
shift and surge of
surface wind"]
CB --> R["Heavy rain
visibility, runway water,
engine water ingestion"]
CB --> P["Pressure jumps
altimeter errors"]Notes Part C likes:
- Hail can fall from the anvil downwind of the core, into air that looks clear. It is not confined to the precipitation shaft.
- Radar sees precipitation, not turbulence. Severe turbulence can exist in weak-echo regions on the edges of storms and above them.
- Pressure changes under storms (a rise in the cold pool, a fall ahead of it) can introduce small altimeter errors near the ground.
- Lightning strikes to aircraft are common in and near storms; aircraft are designed to conduct the current around the cabin, but strikes can damage composite parts and electronics. The electrification physics is in Atmospheric Electricity.
Thunderstorm weather over India
| Season | Region | Type | Aviation impact |
|---|---|---|---|
| Pre-monsoon (March–May) | East and north-east India, Bangladesh | Nor’westers (Kalbaishakhi): squall lines with violent gusts | Severe squalls, hail, wind shear at Kolkata and the north-east |
| Pre-monsoon | North-west India | Dust storms (andhi) and dry thunderstorms | Visibility drops abruptly; dry microbursts from high-based storms |
| Monsoon (June–September) | Most of India | Embedded convection in monsoon troughs and depressions | Widespread cloud with embedded CB; heavy rain at aerodromes |
| Post-monsoon | South peninsula, Bay of Bengal | Tropical cyclones and north-east monsoon convection | Extensive closures on the east coast during cyclones |
Information for Aviation
The rules for meteorological service to international aviation are set by ICAO Annex 3 (with matching WMO technical regulations); national meteorological services provide it at aerodromes. In India the India Meteorological Department provides aviation meteorological services.
| Product | What it is | Time scope |
|---|---|---|
| METAR | Routine aerodrome observation | Issued at regular intervals, usually hourly or half-hourly |
| SPECI | Special observation when conditions change significantly | Whenever criteria are met |
| TREND | Landing forecast appended to a METAR or SPECI | Next 2 hours |
| TAF | Terminal aerodrome forecast | Several hours to about a day or more |
| SIGMET | Warning of hazardous en-route weather: thunderstorms (obscured, embedded, frequent, squall line), severe turbulence, severe icing, severe mountain waves, heavy dust or sand storm, volcanic ash, tropical cyclones | Short validity, updated as needed |
| AIRMET | Similar warning for lower-level flights, for less severe phenomena | Short validity |
| SIGWX charts | Forecast charts of jets, tropopause height, turbulence, icing, CB areas | Fixed validity times for flight planning |
| ATIS | Recorded broadcast of current aerodrome information | Updated with each observation |
Reading a METAR
A METAR is a coded message. A practice example (fictitious station code):
METAR VXXX 120030Z 00000KT 0200 R28/0350N FG VV001 09/09 Q1019 NOSIG
| Group | Meaning |
|---|---|
VXXX | ICAO station indicator (V-prefixed indicators are used in India and neighbouring regions) |
120030Z | Day 12, 00:30 UTC |
00000KT | Calm |
0200 | Prevailing visibility 200 m (9999 means 10 km or more) |
R28/0350N | Runway visual range on runway 28 is 350 m, no distinct change (U up, D down, N no change) |
FG | Fog |
VV001 | Sky obscured; vertical visibility 100 ft |
09/09 | Temperature 9 °C, dew point 9 °C: saturated |
Q1019 | QNH 1019 hPa |
NOSIG | TREND: no significant change expected in the next 2 h |
Other conventions:
- Wind direction in METAR and TAF is in degrees true; the tower gives surface wind for landing in degrees magnetic, to match runway numbers.
- Cloud amount is in oktas (eighths): FEW 1–2, SCT 3–4, BKN 5–7, OVC 8, followed by base height in hundreds of feet.
CBorTCUis appended for cumulonimbus or towering cumulus. - Ceiling is the height of the base of the lowest cloud layer below 20,000 ft covering more than half the sky (BKN or OVC).
- CAVOK (ceiling and visibility OK) replaces visibility, weather and cloud groups when visibility is 10 km or more, there is no cloud below 1,500 m (5,000 ft) or the highest minimum sector altitude, whichever is greater, no CB or TCU, and no significant weather.
- Weather codes:
RArain,DZdrizzle,SNsnow,TSthunderstorm,SHshower,FZfreezing,FGfog,BRmist,HZhaze,FUsmoke,DUdust,SQsquall; intensity-light,+heavy.
Memory Tricks
Don’t Confuse
| This | vs | That |
|---|---|---|
| Pressure altitude: ISA height of the observed pressure | vs | Density altitude: ISA height of the observed density |
| QFE: reads zero on the aerodrome | vs | QNH: reads aerodrome elevation |
| Indicated altitude in cold air: higher than true | vs | Indicated altitude in warm air: lower than true |
| True airspeed: speed through the air | vs | Ground speed: true airspeed plus wind along track |
| METAR: observation | vs | TAF: forecast for an aerodrome; TREND: 2 h landing forecast attached to a METAR |
| SIGMET: en-route hazards for all flights | vs | AIRMET: lower-level flights, less severe phenomena |
| METAR wind: degrees true | vs | Runway number: magnetic heading ÷ 10 |
| Visibility (horizontal, along the ground) | vs | Vertical visibility (VV, into an obscured sky) and ceiling (base of BKN or OVC) |
Common Mistakes
Practice
All questions below are original practice questions in CSIR NET style. They are not previous-year questions.
Level 1: Foundation
- What does an altimeter set to QFE read when the aircraft is on the runway?
- Give the crosswind component of a 30 kt wind blowing at 30° to the runway.
- Which METAR cloud groups can define a ceiling?
Answers
- Zero (height above the aerodrome).
- 30 sin 30° = 15 kt.
- BKN and OVC (more than half the sky covered), below 20,000 ft.
Level 2: Part B Style
Q1 (practice). An aircraft cruises from an area of QNH 1022 hPa towards one of QNH 1004 hPa while maintaining a constant indicated altitude without changing the subscale setting. Near the surface, the aircraft’s true altitude at the end is approximately:
- (a) 150 m higher than indicated
- (b) 150 m lower than indicated
- (c) 18 m lower than indicated
- (d) unchanged, because the altimeter compensates automatically
Answer and explanation
(b). The difference is 18 hPa, and 18 × 8.3 ≈ 150 m. Moving towards lower pressure, each pressure level lies lower, so the aircraft following a constant-pressure reading descends: it is lower than indicated. The altimeter does not compensate; only resetting the subscale does.
Q2 (practice). On a summer afternoon, which combination gives the longest take-off run for a given aircraft and weight?
- (a) Sea-level aerodrome, 20 °C, dry air
- (b) Sea-level aerodrome, 40 °C, humid air
- (c) Aerodrome at 1,500 m, 40 °C, humid air
- (d) Aerodrome at 1,500 m, 10 °C, dry air
Answer and explanation
(c). Elevation, high temperature and humidity all lower density and raise density altitude, needing a higher true airspeed and giving less thrust. Option (c) combines all three.
Q3 (practice). For runway 09 and a reported wind 040/24KT, the headwind and crosswind components are about:
- (a) 15 kt headwind, 18 kt crosswind
- (b) 18 kt headwind, 15 kt crosswind
- (c) 24 kt headwind, 0 kt crosswind
- (d) 12 kt headwind, 21 kt crosswind
Answer and explanation
(a). The runway heading is about 090°, so the angle is 50°. Headwind = 24 cos 50° ≈ 15.4 kt; crosswind = 24 sin 50° ≈ 18.4 kt from the left. (Strictly, METAR winds are true and runway numbers magnetic; the question ignores the difference.)
Q4 (practice). Which statement about thunderstorm hazards is correct?
- (a) Hail is confined to the region of heaviest radar reflectivity.
- (b) In the cumulus stage, downdrafts dominate the cell.
- (c) Severe turbulence can occur in regions of weak or no radar echo near a storm.
- (d) Icing cannot occur in a cumulonimbus because updrafts are warm.
Answer and explanation
(c). Radar detects precipitation, not turbulence, so the edges of storms and the clear air above and around them can be turbulent with little echo. (a) Hail can fall from the anvil; (b) updrafts dominate the cumulus stage; (d) updrafts carry supercooled water above the freezing level, so CBs are a major icing hazard.
Level 3: Part C Style
Q1 (practice). An aerodrome reports QNH 1003 hPa, field elevation 300 m and temperature 32 °C. Take 8.3 m per hPa and the rule that density altitude rises by 36 m per kelvin above ISA.
(i) Find the pressure altitude. (ii) Find the ISA temperature at that pressure altitude and the deviation. (iii) Estimate the density altitude. (iv) By roughly what factor does the lift-off true airspeed change compared with ISA sea level, if the density here is 1.10 kg m\(^{-3}\)?
Answer and worked solution
- PA = 300 + (1013.25 − 1003) × 8.3 = 300 + 10.25 × 8.3 ≈ 385 m.
- ISA temperature at 385 m = 15 − 6.5 × 0.385 ≈ 12.5 °C. Deviation = 32 − 12.5 ≈ +19.5 K.
- DA ≈ 385 + 36 × 19.5 ≈ 385 + 702 ≈ 1,090 m.
- \( V \propto \rho^{-1/2} \): \( \sqrt{1.225/1.10} \approx 1.055 \), so about 5–6% higher true airspeed at lift-off, and about 11% more kinetic energy to build up.
Q2 (practice). A crew reads the following practice METAR on approach:
METAR VXXX 151130Z 27018G32KT 3000 +TSRA SCT015 BKN025CB 30/24 Q1001 TEMPO 31035G50KT 1200 +TSRA
Which statements are correct?
(A) The ceiling is 2,500 ft, with cumulonimbus. (B) Gusts of 32 kt imply the crew should expect rapid airspeed fluctuations on short final. (C) The TEMPO group warns of a temporary wind shift and strengthening consistent with a thunderstorm gust front or downburst. (D) The station is at its dew point, so fog is the main visibility restriction.
- (a) A, B and C only
- (b) A and D only
- (c) B and C only
- (d) A, B, C and D
Answer and worked solution
(a) A, B and C only.
- (A) SCT015 is not a ceiling; BKN025CB is the lowest layer covering more than half the sky, at 2,500 ft, and it is cumulonimbus. Correct.
- (B) Mean 18 kt with gusts to 32 kt is a 14 kt gust increment: airspeed will fluctuate. Correct.
- (C) A temporary veer to 310° with 35 kt gusting 50 kt in heavy thunderstorm rain is the signature of storm outflow. Correct.
- (D) Temperature 30 °C and dew point 24 °C differ by 6 K, so the air is not saturated; the restriction is heavy rain (
+TSRA), not fog. Incorrect.
Q3 (practice). An aircraft is 1,500 m above a sea-level aerodrome by its QFE altimeter. The surface temperature is −20 °C and the lapse rate is the ISA value. (i) Find the ISA mean temperature and the actual mean temperature of the layer. (ii) Estimate the true height. (iii) Explain why this error matters most on an instrument approach and not at cruise.
Answer and worked solution
- ISA mean over 0–1,500 m = 15 − 6.5 × 0.75 = 10.125 °C = 283.3 K. Actual mean = −20 − 4.875 = −24.875 °C = 248.3 K.
- \( z_\text{true} \approx 1500 \times 248.3/283.3 \approx \) 1,315 m: about 185 m below indicated.
- On approach, minimum altitudes guarantee clearance above terrain and obstacles, so a 185 m over-reading eats into that clearance. At cruise all aircraft fly the same standard setting in the same air mass and share the error, so vertical separation between them is preserved and terrain is far below.
Quick Revision Table
| Item | Fact |
|---|---|
| Lift | \( L = \tfrac12 \rho V^2 S C_L \); lift-off TAS \( \propto \rho^{-1/2} \) |
| ISA | 15 °C, 1013.25 hPa, 1.225 kg m\(^{-3}\); 6.5 K km\(^{-1}\) to 11 km |
| Pressure–height | about 8.3 m (27 ft) per hPa near sea level |
| QFE / QNH / standard | Zero on field / field elevation / flight levels |
| Altimeter errors | High to low or warm to cold: lower than indicated |
| Cold error | \( z_\text{true} \approx z_\text{ind}\,\bar T_\text{act}/\bar T_\text{ISA} \) |
| Density altitude | Hot, high, humid raise it; about 36 m (120 ft) per K above ISA |
| Wind components | Headwind \( V\cos\theta \); crosswind \( V\sin\theta \) |
| Take-off and landing | Into wind; tailwind lengthens the roll |
| Cruise hazards | CAT, mountain waves, CB tops, ice crystals, volcanic ash |
| Approach hazards | Low ceiling and visibility, wind shear, gusts, wet runway |
| Thunderstorm stages | Cumulus (updraft), mature (up + down, rain at surface), dissipating (downdraft) |
| CB hazards | Turbulence, icing, hail (even under anvil), lightning, microbursts, gust front, heavy rain |
| Products | METAR, SPECI, TREND (2 h), TAF, SIGMET, AIRMET, SIGWX, ATIS |
| Cloud amount | FEW 1–2, SCT 3–4, BKN 5–7, OVC 8 oktas; ceiling = lowest BKN/OVC below 20,000 ft |
| CAVOK | Vis ≥ 10 km, no cloud below 5,000 ft (or MSA), no CB/TCU, no significant weather |
Key Takeaways
What’s Next
- Icing and Turbulence — the physics of ice accretion, the Richardson number, CAT and mountain waves.
- Visibility and Wind Shear — fog, Koschmieder’s law, RVR and the microburst encounter.
- Nowcasting — how radar, satellite and lightning data give warnings for the next couple of hours.
- Atmospheric Optics — the optics behind visibility and refraction.
- Quick Revision — the whole unit on one page.