Skip to content

Coal: Origin, Rank, Petrography and Indian Resources

CSIR NET Earth Sciences Part C: peat and coalification, coal rank, proximate analysis, lithotypes and macerals, and India's Gondwana and Tertiary coalfields.

  • 22 min read
  • Updated
On this page · 15 sections
  1. Prerequisites
  2. The Hook: A Leaf in the Coal
  3. From Plants to Peat
  4. Coalification
  5. Coal Rank
  6. Coal Analysis
  7. Coal Petrography
  8. Indian Coal Resources
  9. Memory Tricks
  10. Don’t Confuse
  11. Common Mistakes
  12. Practice
  13. Quick Revision Table
  14. Key Takeaways
  15. What’s Next

Prerequisites

The Hook: A Leaf in the Coal

From Plants to Peat

Coal is a combustible sedimentary rock containing more than 50% by weight (and more than 70% by volume) of carbonaceous material, formed from compacted and altered plant remains. The first stage is peat, which forms only where plant production outpaces decay.

Conditions for peat accumulation

RequirementWhy
Abundant plant growthwarm or temperate humid climate; high productivity
Waterlogginga high water table keeps the litter anoxic, which stops aerobic fungal and bacterial decay
Slow, steady subsidenceaccommodation must keep pace with peat growth; too fast drowns the mire, too slow lets it dry and oxidise
Little clastic inputrivers carrying mud dilute the peat and raise the ash; the best seams form away from active channels
Acidic waterlow pH (humic acids) inhibits bacteria

The environments are mires: swamps (forested), marshes (herbaceous), fens (fed by groundwater, less acidic) and raised bogs (fed only by rain, very acidic, low ash). Coal basins are commonly grouped as paralic (near the sea: deltas, coastal plains; marine bands within the sequence, often higher sulfur) and limnic (inland: intermontane or intracratonic basins with lakes and rivers, no marine influence). The Indian Gondwana basins are limnic.

Autochthonous and allochthonous coal

TypeEvidenceExample
In situ (autochthonous)rooted seat-earth (underclay, fireclay or ganister) below the seam; upright stumps; lateral continuity; low ashmost Carboniferous coals of Europe and North America
Drift (allochthonous)no seat-earth; transported plant debris; high and variable ash; sharp contacts; graded or laminated texturesome lacustrine and deltaic coals

How much peat makes a seam?

Peat loses most of its water and much of its volume on burial. Commonly quoted peat-to-coal compaction ratios range from a few to about ten for bituminous coal, and they vary with the peat type and rank. With a ratio of 10:1 and a peat accumulation rate of 1 mm per year (both assumptions for the arithmetic), a 3 m bituminous seam needs 30 m of peat and about 30,000 years of uninterrupted mire growth. This is why thick seams imply long-lived, stable mires and why seam splitting records interruptions by river sediment.

Coalification

Coalification is the conversion of peat through lignite and bituminous coal to anthracite. It has two stages:

  1. Biochemical stage (peatification and early diagenesis): bacterial and fungal decay, humification, formation of humic acids; ends at about the lignite stage.
  2. Geochemical (thermal) stage: after burial, temperature and time drive loss of water, \( \text{CO}_2 \), then methane and other volatiles; aromatic carbon structures grow and become ordered.
graph LR
    P[Peat] --> L[Lignite / brown coal]
    L --> SB[Sub-bituminous]
    SB --> HV[High-volatile bituminous]
    HV --> MV[Medium-volatile bituminous]
    MV --> LV[Low-volatile bituminous]
    LV --> SA[Semi-anthracite]
    SA --> A[Anthracite]
    A --> MA[Meta-anthracite]
    MA --> G[Graphite]

What drives it

FactorEffect
Temperaturethe main control; coalification reactions are thermally activated
Timelonger heating gives higher rank at the same temperature; old coals can reach a given rank at lower temperature
Pressurelithostatic pressure compacts and expels water at low rank, but does not drive the chemical changes; tectonic stress gives anisotropy (bireflectance) of vitrinite
Igneous intrusionslocal contact metamorphism; coal next to dykes and sills becomes natural coke. In the Damodar valley coalfields, heat-affected coal near intrusions is called jhama

Hilt’s law: in a given area, coal rank increases with depth, so volatile matter decreases downwards in a vertical sequence of seams. It is the coal-field expression of the geothermal gradient. Departures from it point to intrusions, unusual heat flow or later tectonic uplift and burial.

Coal Rank

Rank is the degree of coalification. It is distinct from type (what plant material and macerals the coal is made of) and grade (how much mineral matter it contains). A high-ash coal can be high rank; a clean coal can be low rank.

Rank parameters and how they change

PropertyTrend as rank increases
Carbon (daf)rises, from about 50–60% in peat to above 90% in anthracite
Oxygenfalls steadily
Hydrogenroughly constant through bituminous, then falls in anthracite
Moisture (bed or inherent)falls sharply in the low ranks
Volatile matter (dmmf)falls, especially through the bituminous ranks
Calorific valuerises to a maximum in the low-to-medium volatile bituminous range, then levels off or falls slightly in anthracite
Vitrinite reflectance \( R_o \)rises continuously; the most widely used single rank parameter
Liptinite fluorescencestrong at low rank, lost by about the medium-volatile bituminous stage
Coking (caking) propertyabsent in lignite, best in medium-volatile bituminous, absent in anthracite

Different parameters work best in different rank ranges: moisture and calorific value for low-rank coals, volatile matter for bituminous coals and reflectance across the whole range, especially at high rank where volatile matter changes little.

Rank classification

The ASTM scheme (D388) uses fixed carbon and volatile matter (dry, mineral-matter-free) for higher ranks and calorific value (moist, mineral-matter-free) for lower ranks. Approximate reflectance values are added for orientation.

RankFixed carbon, dmmf (%)Volatile matter, dmmf (%)Classified by\( R_o \) (about, %)
Lignite——calorific value (lowest)below about 0.4
Sub-bituminous——calorific valueabout 0.4–0.6
High-volatile bituminousbelow 69above 31calorific valueabout 0.5–1.1
Medium-volatile bituminous69–7822–31fixed carbonabout 1.1–1.5
Low-volatile bituminous78–8614–22fixed carbonabout 1.5–2.0
Semi-anthracite86–928–14fixed carbonabout 2.0–2.5
Anthracite92–982–8fixed carbonabove about 2.5
Meta-anthraciteabove 98below 2fixed carbonhigher

Reflectance boundaries differ slightly between schemes; treat them as approximate. Peat is not a coal rank in the ASTM scheme, and “brown coal” is the European term for lignite and the softer sub-bituminous coals.

Coal Analysis

Proximate and ultimate analysis

AnalysisMeasuresNotes
Proximatemoisture (M), volatile matter (VM), ash (A), fixed carbon (FC)FC is by difference: \( \text{FC} = 100 - (\text{M} + \text{VM} + \text{A}) \)
UltimateC, H, N, S, OO usually by difference
Calorific valuegross (higher) and net (lower) heating valuebomb calorimeter
Coking testsfree swelling index (FSI), Gray–King, plastometry, dilatometryneeded for metallurgical coal

Ash is the inorganic residue after combustion; mineral matter is what was present before combustion (clays, quartz, carbonates, pyrite). Mineral matter is larger than ash, because clays lose water and carbonates lose \( \text{CO}_2 \) and pyrite changes to oxide on burning.

Reporting bases

BasisExcludesConversion from air-dried (ad)
Dry (db)moisture\( X_{db} = X_{ad}\,\dfrac{100}{100 - \text{M}} \)
Dry, ash-free (daf)moisture and ash\( X_{daf} = X_{ad}\,\dfrac{100}{100 - \text{M} - \text{A}} \)
Dry, mineral-matter-free (dmmf)moisture and mineral matter\( X_{dmmf} = X_{ad}\,\dfrac{100}{100 - \text{M} - \text{MM}} \)

Mineral matter is estimated with the Parr formula, \( \text{MM} = 1.08\,\text{A} + 0.55\,\text{S} \), and the ASTM rank calculation corrects fixed carbon for sulfur:

$$\boxed{\text{FC}_{dmmf} = \frac{\text{FC} - 0.15\,\text{S}}{100 - (\text{M} + 1.08\,\text{A} + 0.55\,\text{S})}\times 100}$$

Calorific value from the ultimate analysis

A Dulong-type formula estimates the gross calorific value from mass fractions of C, H, O and S:

$$\text{GCV (MJ kg}^{-1}) \approx 33.8\,C + 144\left(H - \frac{O}{8}\right) + 9.4\,S$$

The term \( O/8 \) treats oxygen as already bound to hydrogen as water. For C = 0.80, H = 0.05, O = 0.08, S = 0.01 it gives about 32.9 MJ kg\(^{-1}\), typical of a bituminous coal. The formula works for bituminous coals and is less reliable for lignite.

Indian grading

India has graded non-coking coal by Useful Heat Value, computed from ash and moisture (both determined at 60% relative humidity and 40 °C):

$$\text{UHV (kcal kg}^{-1}) = 8900 - 138\,(\text{A} + \text{M})$$

The UHV scheme was replaced for non-coking coal by grading on gross calorific value in bands of 300 kcal kg\(^{-1}\) (grades G1 to G17). Coking coal is graded mainly by its ash content. The formula shows the cost of ash: every 1% of ash plus moisture removes 138 kcal kg\(^{-1}\) of useful heat.

Coal Petrography

Lithotypes (megascopic)

Marie Stopes (1919) named four lithotypes of humic banded coal, recognised in hand specimen:

LithotypeAppearanceDominant maceral group
Vitrainbright, glassy, black bands a few millimetres thick; conchoidal fracture; well cleatedvitrinite
Clarainsemi-bright, finely laminated with silky lustrevitrinite with liptinite and inertinite
Duraindull, grey-black, hard, granular; uneven fractureinertinite and liptinite
Fusainsoft, friable, fibrous, charcoal-like; soils the fingersinertinite (fusinite)

Humic coals are banded and formed from woody peat. Sapropelic coals are unbanded, fine-grained and formed from organic mud in open water: cannel coal (rich in spores, burns with a bright candle-like flame) and boghead coal or torbanite (rich in algae such as Botryococcus). Sapropelic coals are hydrogen-rich, oil-prone and link coal to oil shale.

Macerals (microscopic)

Macerals are the microscopically recognisable organic constituents of coal, the equivalent of minerals in a rock. They are studied in polished blocks under reflected light in oil, and in blue or ultraviolet light for fluorescence. The ICCP (International Committee for Coal and Organic Petrology) groups them into three groups:

GroupOriginReflectanceFluorescenceH contentMain macerals
Vitrinite (huminite in low-rank coal)humified woody and cortical tissue (lignin, cellulose)intermediate; the reference for rankweak or noneintermediatetelinite (cell structure), collinite (structureless; in the newer scheme telovitrinite, detrovitrinite, gelovitrinite)
Liptinite (exinite)hydrogen-rich plant parts: spores, cuticles, resins, waxes, algae, corkloweststrong at low rankhighestsporinite, cutinite, resinite, alginite, suberinite, bituminite, exsudatinite
Inertinitecharred (fire) or oxidised, fungally attacked plant matterhighestnonelowestfusinite, semifusinite, macrinite, micrinite, funginite (formerly sclerotinite), inertodetrinite, secretinite

Behaviour on heating separates them into reactives (vitrinite, liptinite and part of the semifusinite), which soften and fuse in a coke oven, and inerts (most inertinite and mineral matter), which do not.

Reflectance of the three groups converges with rank: liptinite brightens fastest, and by the medium- to low-volatile bituminous stage it can no longer be told apart from vitrinite in reflected light.

Microlithotypes

Microlithotypes are maceral associations in bands at least 50 µm wide:

ClassMaceralsExamples
Monomaceralone group dominantvitrite, liptite, inertite
Bimaceraltwo groupsclarite (V + L), durite (I + L), vitrinertite (V + I)
Trimaceralall threeduroclarite, clarodurite, vitrinertoliptite

The hand-specimen lithotypes are built of microlithotypes: vitrain is mostly vitrite; clarain is rich in clarite; durain is rich in durite.

What coal petrography is used for

UseHow
Rankmean random vitrinite reflectance in oil, at a wavelength of 546 nm
Coking blend designrank (\( R_o \)) plus the reactive : inert ratio predicts coke strength
Thermal maturity of sedimentary basinsvitrinite reflectance of dispersed organic matter (the same measurement as in Petroleum)
Depositional environmentgelification of tissue (vitrinite) needs wet conditions; inertinite needs fire or oxidation in a drier, fluctuating mire. Ratios such as a gelification index (vitrinite-type over inertinite-type macerals) and a tissue preservation index (structured over unstructured tissue) are used, in several variants
Hydrocarbon potentialliptinite content and fluorescence indicate oil-proneness

Indian Coal Resources

India’s coal resources are estimated and updated each year by the Geological Survey of India (GSI) and grouped as proved, indicated and inferred. Roughly 99% of the resource is in Gondwana basins; the rest is Tertiary coal in the North-East. Lignite is accounted separately. Odisha, Jharkhand and Chhattisgarh hold the largest shares of the coal resource; Tamil Nadu holds the largest share of the lignite.

Gondwana coal

The Gondwana basins are intracratonic rift basins (half-grabens) aligned along old Precambrian structural trends. They were filled from the Late Carboniferous to the Early Cretaceous; the coal is mostly Permian.

Unit (Lower Gondwana, Damodar valley)Character
Talchir Formationglacial tillites, varved shales and boulder beds at the base: the Late Palaeozoic Gondwana glaciation
Karharbari Formationcoarse sandstones with coal; the Giridih coalfield’s Karharbari seams are of high quality
Barakar Formationsandstone–shale–coal cycles; the most important coal-bearing unit in India
Barren Measures (Ironstone Shale in Raniganj)shales with ironstone bands; little coal
Raniganj Formationthe second main coal-bearing unit, Late Permian
Panchet Formation (Early Triassic) and youngerred beds; no significant coal

The Talchir, Karharbari, Barakar, Barren Measures and Raniganj units carry the Glossopteris–Gangamopteris flora above the glacial beds; the stratigraphy is treated in more detail in Phanerozoic Stratigraphy of India.

Valley / basinMajor coalfieldsState(s)Notes
Damodar–KoelRaniganj, Jharia, East and West Bokaro, North and South Karanpura, Giridih, RamgarhWest Bengal, JharkhandJharia is India’s main source of prime coking coal (Barakar seams); long-burning mine fires; Raniganj is the oldest worked Indian coalfield
RajmahalRajmahal hills coalfieldsJharkhandLower Gondwana coal below the Early Cretaceous Rajmahal Traps
Son–MahanadiSingrauli, Sohagpur, Korba, Mand–Raigarh, Hasdeo–ArandMadhya Pradesh, Uttar Pradesh, Chhattisgarhlarge thick seams; opencast mining for power
Talcher, Ib valleyOdishalarge reserves of high-ash non-coking coal
Pranhita–GodavariSingareni (Godavari valley) and othersTelangana, Andhra Pradesh
Wardha valleyWardha, KampteeMaharashtra
SatpuraPench–Kanhan, PathakheraMadhya Pradesh

Character: high ash (commonly 25–45% in run-of-mine coal), much of it as finely disseminated mineral matter that is difficult to wash out; low sulfur (generally below 1%); inertinite-rich; mostly high-volatile bituminous and sub-bituminous rank, with medium-volatile coking coals in Jharia and parts of other Damodar coalfields.

Tertiary coal

RegionExamplesCharacter
AssamMakum coalfield (Ledo, Tikak, Tipong), Dilli–JeyporePaleogene (Oligocene coals in the Barail Group)
MeghalayaGaro, Khasi and Jaintia hillsPaleogene
Arunachal Pradesh, NagalandNamchik–Namphuk and othersPaleogene

Tertiary coals are low in ash but high in sulfur (often several per cent, much of it organic sulfur), vitrinite-rich, high-volatile and strongly caking but with poor coke strength. The high sulfur is usually linked to marine influence on the peat (paralic setting).

Lignite

AreaStateAge (broad)
NeyveliTamil NaduTertiary (Neogene)
Barmer, Bikaner (Palana), NagaurRajasthanPaleogene
Kutch (Panandhro), Bharuch, BhavnagarGujaratPaleogene–Neogene
Minor occurrencesJammu and Kashmir, Kerala, PuducherryTertiary

Lignite has high moisture and low calorific value and is used mainly in pithead power stations.

FeatureGondwana coalTertiary coalLignite
Agemainly PermianPaleogenePaleogene–Neogene
Settingintracratonic rifts, limnicforeland of the North-East, paralic influencecoastal and western basins
Ashhighlowvariable
Sulfurlowhighvariable, often moderate to high
Dominant maceralinertinite-richvitrinite-richhuminite
Share of resourceabout 99% of coalunder 1% of coalcounted separately

Memory Tricks

Don’t Confuse

ThisNot this
Rank: degree of coalificationType: maceral composition; grade: amount of mineral matter
Ash: combustion residueMineral matter: inorganic material before combustion (about 1.1 × ash)
Vitrain: a megascopic lithotypeVitrinite: a microscopic maceral group; vitrite: a microlithotype
Fusain: charcoal-like lithotypeFusinite: the maceral that makes it up
Cannel coal: spores, sapropelicBoghead coal: algae, sapropelic
Humic coal: banded, woody peatSapropelic coal: unbanded, organic mud
Hilt’s law: rank increases with depthGussow’s principle: differential entrapment of oil and gas
Jharia: prime coking coal, Damodar valleyNeyveli: lignite, Tamil Nadu
Barakar: main coal formation, Early PermianTalchir: glacial basal unit, no economic coal

Common Mistakes

Practice

All questions below are original practice questions written for this page. They are not from any CSIR NET paper.

Level 1: Foundation

  1. Which maceral group has the highest hydrogen content?
  2. Which Lower Gondwana formation is the main coal-bearing unit of India?
  3. State Hilt’s law in one line.
Answers
  1. Liptinite (exinite).
  2. The Barakar Formation (Early Permian).
  3. In a given area, coal rank increases with depth (volatile matter decreases downwards).

Level 2: Part B Style

Practice Q1. A dull, hard, grey-black coal band with a granular fracture, made mostly of inertinite and liptinite, is:

(a) vitrain (b) clarain (c) durain (d) fusain

Answer: (c) durain

Durain is the dull, hard lithotype built of durite (inertinite + liptinite). Fusain is also inertinite-rich but is soft, fibrous and friable; vitrain is bright.

Practice Q2. A coal has, air-dried: moisture 6%, ash 30%, volatile matter 25%. Its fixed carbon on the dry, ash-free basis is closest to:

(a) 39% (b) 49% (c) 61% (d) 64%

Answer: (c) 61%

FC (ad) \( = 100 - 6 - 30 - 25 = 39\% \). daf: \( 39\times 100/(100 - 6 - 30) = 39/0.64 = 60.9\% \). Option (a) is the air-dried value; option (d) is close to the Parr dmmf value, which uses mineral matter (larger than ash) and a sulfur correction.

Practice Q3. Using \( \text{UHV} = 8900 - 138(\text{A} + \text{M}) \), the useful heat value of a coal with 32% ash and 7% moisture is:

(a) 3,518 kcal kg\(^{-1}\) (b) 4,484 kcal kg\(^{-1}\) (c) 5,382 kcal kg\(^{-1}\) (d) 8,861 kcal kg\(^{-1}\)

Answer: (a) 3,518 kcal per kg

\( 8900 - 138\times 39 = 8900 - 5382 = 3518 \) kcal kg\(^{-1}\). Option (c) is the deduction, not the result; option (d) subtracts only 39.

Practice Q4. Which pairing is incorrect?

(a) Jharia – prime coking coal (b) Makum – Tertiary coal, Assam (c) Neyveli – Permian bituminous coal (d) Talcher – Gondwana non-coking coal, Odisha

Answer: (c)

Neyveli in Tamil Nadu is a Tertiary lignite field. The other pairings are correct.

Level 3: Part C Style

Practice Q5. Vitrinite reflectance and volatile matter for seams in one borehole:

Seam depth (m)\( R_o \) (%)VM, dmmf (%)
3000.6238
6000.8034
9001.8518
1,2001.1529

Which interpretation is best?

(a) The profile obeys Hilt’s law throughout; the 900 m seam is simply deeper. (b) The 900 m seam is anomalously high in rank, most likely because of local heating by an igneous intrusion; the other seams follow Hilt’s law. (c) The 1,200 m seam has been oxidised, lowering its reflectance. (d) Reflectance and volatile matter disagree, so the data are unreliable.

Answer: (b)

Reflectance rises and volatile matter falls with depth for 300, 600 and 1,200 m (high-volatile to medium-volatile bituminous): Hilt’s law. The 900 m seam is out of sequence: \( R_o = 1.85\% \) and VM = 18% make it low-volatile bituminous, higher in rank than the deeper seam. A local heat source such as a sill or dyke (the jhama situation in the Damodar coalfields) explains a single anomalous seam. Option (c) cannot be right because oxidation would not explain the high rank of the shallower seam, and reflectance and VM agree with each other in every row, so (d) is wrong.

Practice Q6. A coal block covers 2.0 km × 1.5 km with an average seam thickness of 8 m and an in situ density of 1.5 t m\(^{-3}\). If 60% of it can be mined, and the seam formed from peat with an assumed compaction ratio of 10:1 accumulating at 1 mm yr\(^{-1}\), which pair of values is correct?

(a) 21.6 Mt mineable; 80,000 years of peat accumulation (b) 36 Mt mineable; 8,000 years (c) 21.6 Mt mineable; 8,000 years (d) 14.4 Mt mineable; 80,000 years

Answer: (a)

In place: \( 2000\times 1500\times 8 = 2.4\times 10^{7} \) m³; \( \times 1.5 = 3.6\times 10^{7} \) t = 36 Mt. Mineable: \( 0.6\times 36 = 21.6 \) Mt.

Peat: \( 8\times 10 = 80 \) m; at 1 mm yr\(^{-1}\) = 0.001 m yr\(^{-1}\): \( 80/0.001 = 80{,}000 \) years. Option (b) gives the in-place tonnage and forgets the compaction; (d) takes 40% instead of 60%.

Practice Q7. Consider these statements about coal petrography:

  1. Fusinite has higher reflectance than vitrinite in the same coal.
  2. Liptinite fluorescence increases steadily from lignite to anthracite.
  3. Sapropelic coals such as boghead are richer in hydrogen than humic coals of the same rank.
  4. A high gelification of plant tissue (high vitrinite) suggests a persistently wet mire.

Which are correct?

(a) 1, 3 and 4 only (b) 1 and 2 only (c) 2, 3 and 4 only (d) 1, 2, 3 and 4

Answer: (a) 1, 3 and 4 only
  • 1 true: inertinite macerals have the highest reflectance at a given rank.
  • 2 false: liptinite fluorescence is strong at low rank and is lost by about the medium-volatile bituminous stage.
  • 3 true: boghead (algal) and cannel (spore) coals are liptinite-rich, so hydrogen-rich and oil-prone.
  • 4 true: gelification of humic tissue needs waterlogged, anoxic conditions; inertinite indicates fire or oxidation in drier conditions.

Quick Revision Table

IdeaFact or formula
Peat conditionshigh productivity, waterlogged anoxic mire, balanced subsidence, little clastic input
Basinsparalic (coastal, marine bands, higher S) vs limnic (inland; Indian Gondwana)
Originin situ (seat-earth, stumps) vs drift (no seat-earth, high ash)
Rank sequencepeat → lignite → sub-bituminous → bituminous (hv, mv, lv) → semi-anthracite → anthracite → meta-anthracite
Controlstemperature and time; Hilt’s law; intrusions give natural coke (jhama)
ASTM boundariesVM dmmf 31 / 22 / 14 / 8 / 2; FC dmmf 69 / 78 / 86 / 92 / 98
Rank parametersmoisture and CV (low rank), VM (bituminous), \( R_o \) (all, especially high rank)
Basesdb \( \times 100/(100 - \text{M}) \); daf \( \times 100/(100 - \text{M} - \text{A}) \); Parr MM \( = 1.08\text{A} + 0.55\text{S} \)
UHV\( 8900 - 138(\text{A} + \text{M}) \) kcal kg\(^{-1}\); now GCV grades G1–G17
Lithotypesvitrain, clarain, durain, fusain (Stopes 1919); cannel and boghead are sapropelic
Maceral groupsvitrinite (huminite), liptinite (exinite), inertinite
Microlithotypesbands at least 50 µm; vitrite, clarite, durite, vitrinertite, trimacerites
Gondwana coalPermian; Barakar and Raniganj formations; high ash, low S, inertinite-rich; about 99% of resource
CoalfieldsDamodar (Raniganj, Jharia, Bokaro, Karanpura, Giridih); Son–Mahanadi (Singrauli, Korba, Talcher, Ib); Godavari (Singareni)
Tertiary coalMakum (Assam), Meghalaya; low ash, high S
LigniteNeyveli (TN), Barmer–Bikaner (Rajasthan), Kutch (Gujarat)

Key Takeaways

What’s Next