Skip to content

Gas Hydrates, Coal-Bed Methane, Nuclear and Non-Conventional Energy

CSIR NET Earth Sciences Part C: gas hydrate stability and BSRs, coal-bed methane, uranium and thorium deposits, shale gas, oil sands and geothermal energy.

  • 25 min read
  • Updated
On this page · 14 sections
  1. Prerequisites
  2. The Hook: Ice That Burns
  3. Gas Hydrates
  4. Coal-Bed Methane
  5. Nuclear Energy Resources
  6. Non-Conventional Hydrocarbons
  7. Geothermal Energy
  8. Memory Tricks
  9. Don’t Confuse
  10. Common Mistakes
  11. Practice
  12. Quick Revision Table
  13. Key Takeaways
  14. What’s Next

Prerequisites

The Hook: Ice That Burns

Gas Hydrates

What a hydrate is

A gas hydrate (clathrate hydrate) is a crystalline solid in which hydrogen-bonded water molecules form cages that enclose small gas molecules. Without the guest molecules the cages are unstable; the gas holds the lattice up. In nature the guest is mostly methane, with some ethane, propane, \( \text{CO}_2 \) and \( \text{H}_2\text{S} \).

StructureUnit cell (water molecules)Cages per unit cellTypical guestsNatural setting
sI (cubic)462 small \( (5^{12}) \) + 6 large \( (5^{12}6^{2}) \)methane, ethane, \( \text{CO}_2 \), \( \text{H}_2\text{S} \)most marine hydrates (microbial methane)
sII (cubic)13616 small \( (5^{12}) \) + 8 large \( (5^{12}6^{4}) \)propane, isobutane with methanethermogenic gas; also forms in gas pipelines
sH (hexagonal)343 small + 2 medium + 1 largelarge molecules (e.g. methylcyclohexane) with a small “help gas”rare in nature

The notation \( 5^{12}6^{2} \) means a cage with 12 pentagonal and 2 hexagonal faces. For sI with every cage filled by methane, the ideal formula is \( \text{CH}_4\cdot 5.75\,\text{H}_2\text{O} \) (46 water molecules / 8 cages).

Where hydrates are stable

Hydrate needs high pressure, low temperature, enough gas (above its solubility in pore water) and water. These conditions are met in:

  • Marine sediments of continental margins, below water depths of a few hundred metres (the exact depth depends on bottom-water temperature).
  • Permafrost regions, onshore and on Arctic shelves, beneath the frozen layer.

The gas hydrate stability zone (GHSZ) in marine sediment runs from the seafloor down to the depth at which the local geotherm crosses the hydrate phase boundary.

graph TD
    A[Seafloor: cold bottom water,
pressure from water column] --> B[GHSZ: hydrate stable
if methane exceeds solubility] B --> C[Base of GHSZ:
geotherm meets phase boundary] C --> D[Free gas trapped below
the hydrate-bearing layer] C -.seismic.-> E[BSR: reversed-polarity reflector
parallel to the seafloor]
ChangeEffect on GHSZ thickness
Deeper water (higher pressure)thicker
Warmer bottom waterthinner, top of stability deeper
Higher geothermal gradientthinner
Salt in pore waterphase boundary shifts to lower temperature: thinner
Heavier gases (ethane, propane; sII)phase boundary shifts to higher temperature: thicker

Detecting hydrates

MethodHydrate signature
Bottom-simulating reflector (BSR)a reflector that mimics the seafloor, cuts across bedding, and has reversed polarity relative to the seafloor, because high-velocity hydrate-bearing sediment overlies low-velocity gas-charged sediment. It marks the base of the GHSZ
Amplitude blankingreduced reflection amplitudes within hydrate-cemented sediment
Well logshigh resistivity and high P-wave velocity in the hydrate zone (hydrate, like ice, is an electrical insulator)
Pore-water chemistrychloride freshening in recovered cores: dissociating hydrate releases fresh water
Core temperaturecold spots on infrared scans, because dissociation is endothermic
Seafloorgas plumes, pockmarks, cold seeps with chemosynthetic communities, authigenic carbonates

Because the BSR sits where the temperature equals the hydrate dissociation temperature at that pressure, it doubles as a thermometer. If the seafloor temperature \( T_0 \), the BSR temperature \( T_{BSR} \) (from the phase diagram at the BSR pressure) and the sediment thermal conductivity \( k \) are known:

$$\boxed{q = k\,\frac{T_{BSR} - T_0}{z_{BSR}}}$$

where \( z_{BSR} \) is the BSR depth below the seafloor. Mapping BSR depth across a margin gives a regional heat-flow map without drilling.

Origin of the methane

Most marine hydrate methane is microbial, from methanogenesis in shallow sediment, with \( \delta^{13}\text{C} \) typically below about −60‰ and almost no ethane or propane. Thermogenic methane migrating from deeper source rocks has heavier carbon isotopes and carries ethane and propane, which can stabilise sII hydrate. Hydrate occurs disseminated in mud, as nodules and veins filling fractures, and, most valuably for production, as pore fill in sands, where saturations can be high.

Resource, hazard and climate

  • Production methods: depressurisation (lowering pressure below the stability limit, the most promising), thermal stimulation, inhibitor injection (methanol, glycols, brines) and \( \text{CO}_2 \)–\( \text{CH}_4 \) exchange, in which \( \text{CO}_2 \) replaces methane in the cages. Short offshore production tests have been made in the Nankai Trough (Japan) and the South China Sea; no field is yet in commercial production.
  • Geohazards: dissociation weakens sediment and has been proposed as a factor in submarine slope failures; drilling through hydrate needs care.
  • Climate: methane is a strong greenhouse gas. Large releases of hydrate methane have been proposed for past warming events such as the Paleocene–Eocene Thermal Maximum, a hypothesis that remains debated.

Gas hydrates in India

India’s National Gas Hydrate Programme (NGHP) has drilled and cored hydrates in the Indian offshore. Expedition NGHP-01 found hydrate in the Krishna–Godavari, Mahanadi and Andaman areas, mostly as fracture fill in clay-rich sediment in KG, and an unusually deep hydrate occurrence in the Andaman. Expedition NGHP-02 targeted sand reservoirs and found high-saturation, sand-hosted hydrate in the KG basin, the kind considered producible. BSRs have been mapped along both the eastern and western margins.

Coal-Bed Methane

How gas is stored in coal

Coal-bed methane (CBM) is natural gas held in coal seams. Unlike a conventional reservoir, coal is both source and reservoir, and most of its gas is adsorbed on the internal surfaces of the coal’s micropores, not held as free gas. Coal has an enormous internal surface area, so at shallow depth it can store several times more gas than the same volume of sandstone.

Storage modeShare
Adsorbed on micropore surfacesthe great majority
Free gas in cleats and fracturessmall
Dissolved in watersmall

The gas is thermogenic (from coalification, mainly at bituminous ranks and above) or biogenic (from microbes, including secondary biogenic gas produced long after burial when groundwater carries microbes into low-rank coal).

The Langmuir isotherm

Adsorption capacity at constant temperature is described by the Langmuir isotherm:

$$\boxed{V = \frac{V_L\,P}{P_L + P}}$$
SymbolMeaning
\( V \)gas content the coal can hold at pressure \( P \) (m³ t\(^{-1}\))
\( V_L \)Langmuir volume: the maximum capacity at infinite pressure
\( P_L \)Langmuir pressure: the pressure at which \( V = V_L/2 \)

Capacity rises steeply at low pressure and flattens at high pressure. It increases with rank in general, and decreases with moisture, ash and temperature. A coal is saturated if its measured gas content equals the isotherm value at reservoir pressure, and undersaturated if it holds less.

Producing CBM: dewater, desorb, diffuse, flow

graph LR
    A[Pump water from the seam
reservoir pressure falls] --> B[Pressure reaches the
critical desorption pressure] B --> C[Methane desorbs from
micropore surfaces] C --> D[Diffuses through the
coal matrix: Fick's law] D --> E[Flows through cleats
to the well: Darcy's law]
  • Critical desorption pressure \( P_{cd} \): the pressure on the isotherm that matches the measured gas content. Gas will not flow until the reservoir pressure is lowered to \( P_{cd} \). Rearranging Langmuir: \( P_{cd} = \dfrac{V\,P_L}{V_L - V} \).
  • Cleats are the natural fractures of coal, perpendicular to bedding: face cleats are continuous; butt cleats are shorter and end against the face cleats. Cleat permeability controls productivity and falls with depth because of rising stress, so the best CBM is a balance between gas content (rising with depth) and permeability (falling with depth).
  • Production profile: water production is high at first and declines; gas production rises over months to years as desorption spreads (“negative decline”), then declines. Produced water disposal is a major environmental issue.
TermMeaning
CBMgas produced from unmined coal seams through wells
Coal mine methane (CMM)methane drained from working or abandoned mines; a safety and greenhouse issue (firedamp)
Ventilation air methanevery dilute methane in mine exhaust air
Enhanced CBM (ECBM)injecting \( \text{CO}_2 \) (adsorbed more strongly than methane) or \( \text{N}_2 \) to displace methane; with \( \text{CO}_2 \) it doubles as geological storage

India. CBM blocks have been awarded in the Gondwana coalfields of the Damodar valley (Raniganj, Jharia, East and West Bokaro, North Karanpura) and the Son valley (Sohagpur), among others; commercial production began in the Raniganj coalfield. Indian Gondwana coals are high in ash, which reduces gas content per tonne of rock, and permeability is a key constraint.

Nuclear Energy Resources

Uranium and thorium geochemistry

PropertyUraniumThorium
Isotopes\( ^{238}\text{U} \) (99.27%, \( t_{1/2} \) 4.47 Gyr), \( ^{235}\text{U} \) (0.72%, 0.704 Gyr), \( ^{234}\text{U} \) (trace)\( ^{232}\text{Th} \) (about 100%, 14.0 Gyr)
Oxidation statesU⁴⁺ (insoluble) and U⁶⁺ (soluble as uranyl, \( \text{UO}_2^{2+} \), especially as carbonate complexes)Th⁴⁺ only
Mobilityhigh in oxidising water; precipitates on reductionvery low; stays in resistant minerals
Main mineralsuraninite \( \text{UO}_2 \) (pitchblende is its fine-grained colloform variety), coffinite \( \text{USiO}_4 \), brannerite, secondary uranyl minerals (autunite, torbernite, carnotite)monazite (Ce, La, Th)\( \text{PO}_4 \), thorianite, thorite, uranothorite
Concentrating processredox fronts: dissolved in oxidised water, precipitated by organic matter, sulfides or \( \text{Fe}^{2+} \)placers: heavy, resistant monazite in beach and river sands

This single contrast (U mobile when oxidised, Th never mobile) explains almost every uranium and thorium deposit type, and it is also why the Th/U ratio of rocks rises during oxidative weathering.

Uranium deposit types

TypeSettingOre controlExamples
Unconformity-relatedProterozoic basin sandstones over metamorphic basementoxidised basinal brine meets reduced (graphitic) basement at the unconformity; exceptionally high gradesAthabasca basin (Canada), Alligator Rivers (Australia); Lambapur–Peddagattu (Telangana)
Sandstone-hostedfluvial and marginal-marine sandstones with organic matter or pyriteoxidised groundwater carries uranium down-dip until it meets reduced ground: roll-front, tabular and basal-channel bodies; often mined by in situ recoveryWyoming and Texas (USA), Kazakhstan, Niger; Domiasiat area (Meghalaya), in Cretaceous sandstone
Quartz-pebble conglomerateArchean–Paleoproterozoic fluvial conglomeratesdetrital uraninite, preserved only under a low-oxygen atmosphereWitwatersrand (South Africa), Elliot Lake (Canada)
IOCG (breccia complex)Proterozoic hematite brecciasU with Cu, Au, REE in oxidised Fe-oxide brecciaOlympic Dam (Australia), the largest known uranium resource
Vein and shear-zonegranites, metamorphic shear zonesfracture-controlled hydrothermal veinsSinghbhum Shear Zone (Jaduguda, Bhatin, Narwapahar, Turamdih, Bagjata); Gogi (Karnataka)
Intrusivealaskites, pegmatites, peralkaline complexesmagmatic uraniniteRössing (Namibia)
Metasomatitesodium-metasomatised (albitised) rocksU introduced with Na metasomatismUkraine; albitite-associated occurrences in Rajasthan
Carbonate-hosteddolostones and limestonesstrata-bound, low grade, large tonnageTummalapalle (Andhra Pradesh), in the phosphatic dolostone of the Vempalle Formation, Cuddapah basin
Surficial (calcrete)arid-zone valley fillU precipitates with V as carnotite on evaporationYeelirrie (Australia)
Phosphorite, black shalemarine phosphorites and organic shalesU substitutes for Ca in apatite, adsorbed on organic mattervery low grade; potential by-product

Indian uranium and thorium

ProvinceDepositsType
Singhbhum Shear Zone (Jharkhand)Jaduguda, Bhatin, Narwapahar, Turamdih, Bagjata, Banduhurang, Mohuldihshear-zone-hosted, with copper, apatite and magnetite; the oldest uranium mining district in India
Cuddapah basin (Andhra Pradesh, Telangana)Tummalapalle (south-western margin); Lambapur–Peddagattu, Chitrial (northern, Srisailam sub-basin)carbonate-hosted strata-bound; unconformity-related
MeghalayaDomiasiat and nearby depositssandstone-hosted, Cretaceous
Bhima basin (Karnataka)Gogifracture-controlled, near basement granite
RajasthanRohil and othersalbitite-associated

Exploration is carried out by the Atomic Minerals Directorate for Exploration and Research (AMD) and mining by Uranium Corporation of India Limited (UCIL).

Thorium: India has large thorium resources, mostly in monazite from the beach and inland placers of Kerala (Chavara), Tamil Nadu (Manavalakurichi), Odisha (Chhatrapur) and Andhra Pradesh, along with ilmenite, rutile, zircon, sillimanite and garnet (the placer process is in Ore-Forming Processes and Metallogeny). India’s limited uranium and large thorium explain the design of its three-stage nuclear programme, described in Energy Resources and Environmental Impact.

Exploration for radioactive minerals

MethodPrinciple
Gamma-ray spectrometry (ground, airborne, borehole)separates the three natural emitters by energy: K from \( ^{40}\text{K} \) at 1.46 MeV; U from its daughter \( ^{214}\text{Bi} \) at 1.76 MeV; Th from its daughter \( ^{208}\text{Tl} \) at 2.61 MeV
Scintillometer and Geiger countertotal radioactivity; quick reconnaissance
Radon emanometryradon gas (from \( ^{226}\text{Ra} \)) in soil gas and water over buried deposits
Hydrogeochemistrydissolved uranium in groundwater and stream water; uranium is mobile in oxidised water
Geologyredox boundaries, unconformities, shear zones, albitisation, hematite alteration

Energy from fission

Each fission of \( ^{235}\text{U} \) releases about 200 MeV. For 1 kg of \( ^{235}\text{U} \):

$$N = \frac{1000}{235.0}\times 6.022\times 10^{23} = 2.56\times 10^{24}\ \text{nuclei}$$$$E = 2.56\times 10^{24}\times 200\times 1.602\times 10^{-13}\ \text{J} = 8.2\times 10^{13}\ \text{J}$$

This equals the heat from about 3,300 tonnes of coal at 25 MJ kg\(^{-1}\). \( ^{235}\text{U} \) is the only naturally occurring fissile nuclide; \( ^{238}\text{U} \) and \( ^{232}\text{Th} \) are fertile, converting by neutron capture to fissile \( ^{239}\text{Pu} \) and \( ^{233}\text{U} \).

Non-Conventional Hydrocarbons

Conventional oil and gas are buoyant accumulations in discrete traps that flow to a well without special stimulation. Unconventional (continuous) resources are spread across large areas, often without a trap, and need special technology: horizontal drilling, hydraulic fracturing, heating or mining.

ResourceWhat it isKey propertiesRecovery
Shale gasgas retained in an organic-rich shale that is its own source and reservoirTOC commonly above about 2%; mature (gas window); brittle (quartz- or carbonate-rich, low clay); nanodarcy permeabilityhorizontal wells with multistage hydraulic fracturing
Shale oil / tight oillight oil in shales or tight siltstones and carbonates in the oil windowas above, oil-window maturityas above
Tight gasgas in low-permeability sandstones (below about 0.1 mD)conventional source, poor reservoirfracturing
Oil shaleimmature, kerogen-rich (type I or II) shalehas not generated oil yetmining and retorting (heating to around 500 °C) or in situ heating
Oil sands (tar sands)sand saturated with bitumen, heavily biodegraded oilAPI gravity below 10°, very viscoussurface mining; steam-assisted gravity drainage (SAGD)
Heavy and extra-heavy oildense, viscous, often biodegraded oilAPI below about 22° (extra-heavy below 10°)steam flooding, in situ combustion
CBM, gas hydratesabove

API gravity classifies crude oils by density:

$$\boxed{^\circ\text{API} = \frac{141.5}{\text{SG}_{60^\circ\text{F}}} - 131.5}$$

Water (SG = 1) is 10°. Light oil is above about 31°, medium 22–31°, heavy 10–22°, extra-heavy and bitumen below 10° (denser than water). Biodegradation by bacteria in shallow, cool reservoirs removes n-alkanes first, lowers API gravity and raises viscosity and sulfur; it is the main way giant heavy-oil and oil-sand deposits (Athabasca in Canada, the Orinoco belt in Venezuela) form.

India. Shales in the Cambay, Krishna–Godavari, Cauvery and Gondwana (Damodar) basins have been studied as shale-gas prospects, and heavy oil occurs in the Bikaner–Nagaur basin of Rajasthan and in parts of Cambay. Underground coal gasification, which burns coal in place to make syngas (CO + H\(_2\)), has also been studied for deep or thin Indian seams and lignite.

Geothermal Energy

Earth’s internal heat comes from radioactive decay (U, Th, K) and primordial heat. It is extracted where heat is concentrated at shallow depth: plate boundaries, hotspots, young intrusions and rifts.

SystemDescriptionExamples
Vapour-dominated hydrothermalsteam fills fractures; the easiest to useLarderello (Italy), The Geysers (USA)
Liquid-dominated hydrothermalhot water, flashes to steam as pressure dropsmost high-temperature fields (Iceland, New Zealand)
Low-enthalpywarm water below about 150 °Cbinary-cycle power, direct heating
Hot dry rock / enhanced geothermal (EGS)hot impermeable rock fractured artificially, water circulatedexperimental; induced seismicity is a concern
Geopressuredhot, overpressured brines with dissolved methaneGulf Coast (USA)
Ground-source heat pumpsshallow, near-constant ground temperature for heating and coolingwidespread

A geothermal field needs a heat source, a reservoir (permeable, fractured rock), a cap rock and recharge water. Surface signs include hot springs, fumaroles, geysers and alteration (sinter, travertine). Silica (and Na–K) geothermometers estimate reservoir temperatures from the chemistry of spring water.

Power plants convert heat to work with a maximum (Carnot) efficiency \( \eta = 1 - T_c/T_h \). A 200 °C reservoir rejecting heat at 30 °C has \( \eta_{max} = 1 - 303/473 = 0.36 \); real plants reach a fraction of this, which is why low-temperature fields are better used for direct heat.

India has mainly low- to moderate-enthalpy geothermal provinces: the Himalaya (Puga valley in Ladakh; Manikaran), the Son–Narmada–Tapi lineament (Tattapani), the west coast, Cambay and the Godavari valley. Details are in Energy Resources and Environmental Impact.

Memory Tricks

Don’t Confuse

ThisNot this
BSR: base of hydrate stability, reversed polarityFlat spot: horizontal fluid contact in a conventional reservoir
CBM: gas from unmined seams by wellsCMM: gas drained from coal mines
Adsorbed gas: on coal surfaces (CBM)Free gas: in pores (conventional, tight gas)
Face cleat: continuousButt cleat: ends against face cleats
Fissile \( ^{235}\text{U} \)Fertile \( ^{238}\text{U} \), \( ^{232}\text{Th} \)
Uraninite: \( \text{UO}_2 \), U⁴⁺, primaryCarnotite, autunite: secondary uranyl (U⁶⁺) minerals
Unconformity-related: high grade, ProterozoicSandstone roll-front: low grade, younger, ISR
Oil shale: immature kerogen, retort itShale oil: mature oil in shale, fracture it
Oil sands: bitumen, API below 10°Tight oil: light oil in low-permeability rock

Common Mistakes

Practice

All questions below are original practice questions written for this page. They are not from any CSIR NET paper.

Level 1: Foundation

  1. How many water molecules are there in the unit cell of structure I gas hydrate?
  2. Which oxidation state of uranium is mobile in groundwater?
  3. Which mineral is India’s main source of thorium?
Answers
  1. 46 (with 8 cages: 2 small, 6 large).
  2. U⁶⁺, as the uranyl ion \( \text{UO}_2^{2+} \), mostly complexed with carbonate.
  3. Monazite, from beach placers.

Level 2: Part B Style

Practice Q1. A seismic section across a continental slope shows a strong reflector about 200 m below the seafloor that parallels the seafloor, cuts across dipping strata and has polarity opposite to the seafloor reflection. It most likely marks:

(a) an oil–water contact (b) the base of the gas hydrate stability zone (c) a diagenetic opal-A to opal-CT transition (d) the top of the oceanic crust

Answer: (b)

These are the defining features of a BSR: parallel to the seafloor (it follows isotherms, which follow the seafloor), cross-cutting bedding, and reversed polarity because high-velocity hydrate-bearing sediment overlies low-velocity gas-bearing sediment. A diagenetic silica front also mimics the seafloor but gives normal polarity, because velocity increases downward across it.

Practice Q2. A coal has Langmuir parameters \( V_L = 25 \) m³ t\(^{-1}\) and \( P_L = 2.5 \) MPa. Its gas content at a reservoir pressure of 5.0 MPa, if saturated, is:

(a) 8.3 m³ t\(^{-1}\) (b) 12.5 m³ t\(^{-1}\) (c) 16.7 m³ t\(^{-1}\) (d) 25 m³ t\(^{-1}\)

Answer: (c)

\( V = 25\times 5.0/(2.5 + 5.0) = 125/7.5 = 16.7 \) m³ t\(^{-1}\). Option (b) is the value at \( P = P_L \); option (d) is \( V_L \), reached only at infinite pressure.

Practice Q3. A crude oil has a specific gravity of 0.85 at 60 °F. Its API gravity and class are:

(a) 35°, light (b) 22°, heavy (c) 10°, extra-heavy (d) 45°, condensate-like

Answer: (a)

\( 141.5/0.85 - 131.5 = 166.5 - 131.5 = 35.0° \). Above about 31° is light oil.

Practice Q4. Which pairing of Indian uranium deposit and type is incorrect?

(a) Tummalapalle – carbonate-hosted, Cuddapah basin (b) Domiasiat – sandstone-hosted, Meghalaya (c) Jaduguda – Singhbhum Shear Zone (d) Lambapur – quartz-pebble conglomerate, Witwatersrand type

Answer: (d)

Lambapur–Peddagattu, in the northern Cuddapah basin, is unconformity-related, at the contact of basin sandstone with basement granite. The other pairings are correct.

Level 3: Part C Style

Practice Q5. At a site, the BSR lies 200 m below a seafloor at 4 °C. At the BSR pressure, the methane hydrate phase boundary gives a temperature of 18 °C. The sediment thermal conductivity is 1.0 W m\(^{-1}\) K\(^{-1}\). At a second site with the same water depth, the BSR is at 280 m below the seafloor. Which statement is correct?

(a) Heat flow at site 1 is 70 mW m\(^{-2}\); site 2 has lower heat flow. (b) Heat flow at site 1 is 70 mW m\(^{-2}\); site 2 has higher heat flow. (c) Heat flow at site 1 is 14 mW m\(^{-2}\); site 2 has lower heat flow. (d) Heat flow at site 1 is 90 mW m\(^{-2}\); BSR depth is unrelated to heat flow.

Answer: (a)

Gradient \( = (18 - 4)/200 = 0.070 \) K m\(^{-1}\); \( q = 1.0\times 0.070 = 0.070 \) W m\(^{-2}\) = 70 mW m\(^{-2}\).

At site 2 the same temperature rise (same water depth, so roughly the same BSR temperature and seafloor temperature) is spread over 280 m: gradient \( = 14/280 = 0.050 \) K m\(^{-1}\), \( q = 50 \) mW m\(^{-2}\). A deeper BSR means lower heat flow. Option (c) divides the 14 K rise by 1,000 m instead of 200 m.

Practice Q6. A coal with \( V_L = 25 \) m³ t\(^{-1}\) and \( P_L = 2.5 \) MPa is at a reservoir pressure of 5.0 MPa, but desorption canister tests give a gas content of only 10 m³ t\(^{-1}\). Which statements are correct?

  1. The coal is undersaturated, at 60% of its capacity.
  2. The critical desorption pressure is about 1.7 MPa.
  3. Gas will begin to desorb as soon as pumping begins.
  4. Reservoir pressure must be drawn down by about two-thirds before gas flows.

(a) 1, 2 and 4 only (b) 1 and 3 only (c) 2 and 3 only (d) 1, 2, 3 and 4

Answer: (a) 1, 2 and 4 only

Capacity at 5.0 MPa: \( 25\times 5/7.5 = 16.7 \) m³ t\(^{-1}\); saturation \( = 10/16.7 = 0.60 \). Statement 1 true.

\( P_{cd} = V P_L/(V_L - V) = 10\times 2.5/15 = 1.67 \) MPa. Statement 2 true.

Since \( P_{cd} \) is well below 5.0 MPa, the early production is water only: statement 3 false. The drawdown needed is \( 5.0 - 1.67 = 3.33 \) MPa, two-thirds of the initial pressure: statement 4 true.

Practice Q7. Present-day \( ^{235}\text{U}/^{238}\text{U} = 1/137.88 \). Half-lives: \( ^{235}\text{U} \) 0.7038 Gyr, \( ^{238}\text{U} \) 4.468 Gyr. The \( ^{235}\text{U} \) abundance (atom %) in natural uranium 2.0 billion years ago was closest to:

(a) 0.72% (b) 1.4% (c) 3.7% (d) 17%

Answer: (c) 3.7%

\( \lambda_{235} = 0.693/0.7038 = 0.9849 \) Gyr\(^{-1}\); \( \lambda_{238} = 0.693/4.468 = 0.1551 \) Gyr\(^{-1}\).

Going back in time, each isotope is multiplied by \( e^{\lambda t} \), so the ratio grows by \( e^{(\lambda_{235} - \lambda_{238})t} = e^{0.8297\times 2.0} = e^{1.659} = 5.26 \).

Ratio then \( = 5.26/137.88 = 0.0381 \); abundance \( = 0.0381/1.0381 = \) 3.7%. This is comparable to the enrichment of light-water reactor fuel, which is why ordinary groundwater could moderate a natural chain reaction at Oklo. Option (a) assumes the abundance has not changed; option (d) is far too high for only about three half-lives of \( ^{235}\text{U} \).

Quick Revision Table

IdeaFact or formula
Hydrate structuressI 46 H₂O, 2 + 6 cages, methane; sII 136 H₂O, 16 + 8 cages, propane; sH 34 H₂O
Ideal sI formula\( \text{CH}_4\cdot 5.75\,\text{H}_2\text{O} \); about 160–170 m³ \( \text{CH}_4 \) (STP) per m³ hydrate
GHSZseafloor to where geotherm crosses phase boundary; thinner with high gradient, warm water, salt
BSRbase of GHSZ; parallels seafloor; reversed polarity; free gas below; gives heat flow \( q = k\Delta T/z \)
Hydrate evidencehigh resistivity and velocity, chloride freshening, IR cold spots
Indian hydratesNGHP: KG (fracture-fill and sand-hosted), Mahanadi, Andaman
CBM storagemostly adsorbed; coal is source and reservoir
Langmuir\( V = V_L P/(P_L + P) \); \( P_{cd} = V P_L/(V_L - V) \)
CBM productiondewater → desorb → diffuse (Fick) → Darcy flow in cleats; face and butt cleats
UraniumU⁶⁺ mobile (uranyl carbonate), U⁴⁺ precipitates; uraninite, pitchblende, coffinite
ThoriumTh⁴⁺ immobile; monazite placers
Deposit typesunconformity, sandstone (roll front), QPC, IOCG, vein, intrusive, metasomatite, carbonate, calcrete
Indian USinghbhum Shear Zone (Jaduguda); Tummalapalle; Lambapur–Peddagattu; Domiasiat; Gogi
Gamma peaksK 1.46, U (Bi-214) 1.76, Th (Tl-208) 2.61 MeV
Fissionabout 200 MeV per fission; 1 kg \( ^{235}\text{U} \) about \( 8.2\times 10^{13} \) J
API\( 141.5/\text{SG} - 131.5 \); light above 31°, heavy 10–22°, bitumen below 10°
Unconventionalshale gas and tight oil (fracking), oil shale (retort), oil sands (SAGD, mining)
Geothermalvapour- and liquid-dominated, EGS, geopressured; Carnot \( 1 - T_c/T_h \)

Key Takeaways

What’s Next

Advertisement
Advertisement