Skip to content

Electrical and Electromagnetic Methods Short Notes

One-page CSIR NET geophysics revision: resistivity arrays, VES curves, Dar Zarrouk, IP, EM response, skin depth, VLF, AFMAG, TEM, MT and GDS formulas and traps.

  • 8 min read
  • Updated
On this page · 10 sections
  1. Part C in one table
  2. The methods at a glance
  3. Resistivity
  4. Induced polarization
  5. Inductive EM
  6. VLF and AFMAG
  7. TEM
  8. Magnetotellurics
  9. Geomagnetic depth sounding
  10. Back to the chapter

Every formula and trap from Resistivity Profiling and Sounding, Induced Polarization, EM Methods: Loop Methods, VLF, AFMAG and TEM and Magnetotellurics and Geomagnetic Depth Sounding, on one page.

Part C in one table

Per the NTA information bulletin for December 2026, Earth Sciences Part C:

GivenAttemptCorrectWrongMaximum
8025+4−1.32100

Only the first 25 answered questions are evaluated. Full pattern on the Earth Sciences overview.

The methods at a glance

MethodSourceMeasuresPhysical propertyBest for
Resistivity (DC)injected current\( \Delta V/I \)resistivitylayering, groundwater, bedrock, contacts
IPinjected current (switched or alternating)decay, or fall of \( \rho \) with frequencychargeabilitydisseminated sulphides, clay
Loop EM (FDEM)coil or loopin-phase, quadratureconductivity, conductance \( \sigma t \)conductors, mapping
VLFnaval transmitter, 15–30 kHztilt, ellipticityconductivitysteep shallow conductors
AFMAGlightning sferics, audioazimuth and tiltconductivityconductors, any strike
TEMswitched-off loopdecay of \( \partial B/\partial t \)conductivity vs depthsoundings, deep conductors
MT / GDSnatural fields, ms to daysE and H / H onlyconductivity vs depth / lateralcrust and mantle, sub-basalt

Resistivity

$$\boxed{V = \frac{\rho I}{2\pi r}} \qquad \boxed{\rho_a = K\frac{\Delta V}{I},\ \ K = \frac{2\pi}{1/AM - 1/BM - 1/AN + 1/BN}}$$
Array\( K \)
Wenner\( 2\pi a \)
Schlumberger (\( L = AB/2 \), \( l = MN/2 \))\( \pi(L^2 - l^2)/2l \approx \pi L^2/2l \)
Dipole-dipole\( \pi n(n+1)(n+2)a \)
Pole-dipole\( 2\pi n(n+1)a \)
Pole-pole\( 2\pi a \)
  • Archie: \( F = \rho_0/\rho_w = a\phi^{-m} \); \( \rho_t = a\phi^{-m}S_w^{-n}\rho_w \).
  • Current above depth \( z \): \( (2/\pi)\tan^{-1}(2z/L) \); half above \( L/2 \), 70% above \( L \).
  • Reciprocity: swapping current and potential pairs leaves \( \rho_a \) unchanged.
  • Worked: Wenner \( a = 20 \) m, 0.48 V, 0.2 A → 302 \( \Omega\,\text{m} \); Schlumberger 50/2 m, 15 mV, 0.1 A → 294 \( \Omega\,\text{m} \).
ProfilingSounding (VES)
fixed spacing, array movesfixed centre, spacing grows
lateral changechange with depth
Wenner, dipole-dipole, gradientSchlumberger preferred

Sounding curves

$$\boxed{k = \frac{\rho_2 - \rho_1}{\rho_2 + \rho_1}} \qquad \frac{\rho_a}{\rho_1}\Big|_{\text{Wenner}} = 1 + 4\sum_n k^n\left[\frac{1}{\sqrt{1 + (2nh/a)^2}} - \frac{1}{\sqrt{4 + (2nh/a)^2}}\right]$$
TypeOrderShape
H\( \rho_1 > \rho_2 < \rho_3 \)minimum
K\( \rho_1 < \rho_2 > \rho_3 \)maximum
A\( \rho_1 < \rho_2 < \rho_3 \)rising
Q\( \rho_1 > \rho_2 > \rho_3 \)falling
$$\boxed{S = \sum\frac{h_i}{\rho_i}} \qquad \boxed{T = \sum h_i\rho_i} \qquad \rho_\ell = H/S,\ \ \rho_t = T/H$$
  • Insulating basement: Schlumberger branch at 45°, \( \rho_a = L/S \) (Wenner \( 2a\ln 2/S \)).
  • Equivalence: thin conductor (H, A) → only S; thin resistor (K, Q) → only T. Suppression: thin intermediate layer invisible.
  • Anisotropy: \( \lambda = \sqrt{\rho_t/\rho_\ell} \), \( \rho_m = \sqrt{\rho_t\rho_\ell} \); layer appears as \( \rho_m \), thickness \( \lambda h \).
  • Paradox of anisotropy: along strike reads \( \rho_m \); across strike reads \( \rho_\ell \) (smaller).
  • Interpretation: master curves and auxiliary point charts → Ghosh linear filter → least-squares inversion.

Induced polarization

MechanismCauseSize
Electrode (grain)ionic–electronic transfer at metallic grainslarge
Membrane (electrolytic)ion-selective clay-lined poressmaller
$$\boxed{M = \frac{V_s}{V_p}}\ \ \text{or}\ \ \boxed{M = \frac{1}{V_p}\int_{t_1}^{t_2}V_s\,dt\ (\text{ms})}$$$$\boxed{FE = \frac{\rho_{dc} - \rho_{ac}}{\rho_{ac}}} \qquad \boxed{MF = 2\pi\times10^5\frac{FE}{\rho_{dc}}} \qquad PFE = 100\,FE$$$$\boxed{\rho(\omega) = \rho_0\left[1 - m\left(1 - \frac{1}{1 + (i\omega\tau)^c}\right)\right]}$$
  • Cole–Cole limits \( \rho_0 \) and \( \rho_0(1 - m) \); so \( m = FE/(1 + FE) \approx FE \); phase peak near \( 1/(2\pi\tau) \).
  • Seigel: \( m_a = \sum(\partial\ln\rho_a/\partial\ln\rho_i)m_i \).
  • Dipole-dipole pseudo-depth \( (n + 1)a/2 \); pant’s-leg pattern; invert for true sections.
  • Worked: 120/112 \( \Omega\,\text{m} \) → FE 0.0714, PFE 7.14, MF 374. Decay \( 10e^{-t/0.5} \) mV, \( V_p = 500 \) mV, window 0.1–1.1 s → 7.1 ms.
  • Targets: disseminated sulphides (high IP, modest \( \rho \) low). False targets: graphite, barren pyrite, clay. Saline water: low \( \rho \), low IP.

Inductive EM

$$\boxed{G = \frac{\alpha^2 + i\alpha}{1 + \alpha^2},\ \ \alpha = \frac{\omega L}{R}} \qquad \boxed{\delta = 503\sqrt{\rho/f}\ \text{m}}$$
\( \alpha \)In-phaseQuadratureQ/ILag
\( \ll 1 \) (poor conductor)smalldominantlargenear 90°
10.50.5 (maximum)1135°
\( \gg 1 \) (good conductor)near 1smallsmallnear 180°
  • Worked: \( L/R = 1 \) ms at 1 kHz → \( \alpha = 6.28 \), Q/I 0.16, lag 171°; \( L/R = 0.1 \) ms → \( \alpha = 0.63 \), Q/I 1.59, lag 122°.
  • Low induction number (\( s \ll \delta \)): \( \sigma_a = 4(H_s/H_p)_{quad}/(\omega\mu_0 s^2) \); 10 m, 10 kHz, 0.5% → 2.53 mS/m.
  • HLEM over thin vertical sheet: zero when either coil is over it; negative anomaly as wide as the coil spacing. \( H_p \propto 1/s^3 \).
  • Turam: fixed loop or cable, two receivers: field ratio and phase difference.
  • Tilt-angle: crossover over conductor.

VLF and AFMAG

  • VLF: naval transmitters, about 15–30 kHz; plane wave; horizontal H perpendicular to the station direction; couples with conductors striking toward the station.
  • Measures tilt (in-phase) and ellipticity (quadrature); crossover at conductor.
  • Fraser filter \( \boxed{(M_3 + M_4) - (M_1 + M_2)} \), plotted between \( M_2 \) and \( M_3 \). Karous–Hjelt: current-density pseudosection.
  • VLF-R: \( \rho_a = \lvert E/H\rvert^2/\omega\mu_0 \); skin depth 36 m (100 \( \Omega\,\text{m} \), 20 kHz).
  • AFMAG: worldwide lightning (sferics), audio band; azimuth and tilt of the natural field; deeper than VLF, any strike, but intermittent.

TEM

$$\boxed{d \approx \sqrt{\frac{2t}{\mu_0\sigma}} = 1262\sqrt{\rho t}\ \text{m}} \qquad \boxed{\tau_{\text{sphere}} = \frac{\mu_0\sigma a^2}{\pi^2}}$$
ModelLate-time decay
Uniform half-space\( t^{-5/2} \) (straight on log–log); 1 → 4 ms: factor 32
Confined conductor\( e^{-t/\tau} \) (straight on semi-log)
  • Measures with the primary off: no primary to cancel, geometry less critical.
  • Early time shallow, late time deep (for layered ground); long \( \tau \) = good conductor.
  • Worked: 200 µV at 2 ms, 50 µV at 6 ms → \( \tau = 2.89 \) ms; 50 \( \Omega\,\text{m} \): 282 m at 1 ms, 892 m at 10 ms.

Magnetotellurics

$$\boxed{\rho_a = \frac{\lvert Z\rvert^2}{\omega\mu_0} = 0.2\,T\left\lvert\frac{E}{B}\right\rvert^2}\ (\text{mV/km, nT, s}) \qquad \boxed{\delta = 503\sqrt{\rho T}}$$
PhaseMeaning
45°uniform
> 45°resistivity decreasing with depth
< 45°resistivity increasing with depth
  • Sources: lightning above about 1 Hz, magnetosphere below; dead bands near 1 Hz and a few kHz; plane-wave (Tikhonov–Cagniard) assumption.
  • Bostick: \( D = 356\sqrt{\rho_a T} \), \( \rho_B = \rho_a(\pi/2\varphi - 1) \); 60° → \( \rho_a/2 \), 30° → \( 2\rho_a \).
  • S-line: slope +1 (log \( \rho_a \) vs log T), \( \varphi \to 0 \), \( S = \sqrt{T/2\pi\mu_0\rho_a} \) (400 \( \Omega\,\text{m} \) at 100 s → 178 S). Perfect conductor below: slope −1, \( \varphi \to 90° \).
  • Worked: 10 mV/km, 2 nT, 10 s → 50 \( \Omega\,\text{m} \); \( \delta \) 11.3 km; Bostick depth 8.0 km.
  • Remote reference removes bias from local magnetic noise.
TensorCondition
1-D\( Z_{xx} = Z_{yy} = 0 \), \( Z_{xy} = -Z_{yx} \)
2-D (strike axes)diagonal zero, \( Z_{xy} \ne -Z_{yx} \)
Swift skew\( \lvert Z_{xx} + Z_{yy}\rvert/\lvert Z_{xy} - Z_{yx}\rvert \): small for 1-D/2-D
TE (E-polarisation)TM (B-polarisation)
E along strike, \( H_z \) presentH along strike, no \( H_z \)
currents along strike, inductivecurrents cross strike, charges, galvanic
conductorsresistors and contacts
  • Static shift: \( \log\rho_a \) shifted by a constant; phase unchanged; depths scale by \( \sqrt{s} \); correct with TEM or spatial methods.
  • Phase tensor and Groom–Bailey decomposition handle galvanic distortion.

Geomagnetic depth sounding

  • Tipper \( \boxed{H_z = T_{zx}H_x + T_{zy}H_y} \); zero over 1-D Earth.
  • Induction arrows: Parkinson toward conductors, Wiese away; perpendicular to 2-D strike; coast effect toward the sea.
  • Arrays of magnetometers locate lateral conductors; observatory Sq and Dst data, split into external and internal parts, give the mantle profile (conductivity rises with depth).
  • C-response \( C = Z/i\omega\mu_0 \), \( \rho_a = \omega\mu_0\lvert C\rvert^2 \); Re \( C \) ≈ depth to induced currents.

Back to the chapter

Return to the Electrical and Electromagnetic Methods overview, or revise the spectral tools in Signal Processing.

Advertisement
Advertisement