Resistivity Profiling and Sounding
DC resistivity for CSIR NET geophysics: point-source potential, Wenner, Schlumberger and dipole-dipole factors, VES curves, Dar Zarrouk parameters, equivalence.
- 24 min
On this page · 13 sections
Prerequisites
- Electrostatics, Gauss’s Law, Laplace’s Equation and Boundary-Value Problems: Laplace’s equation, boundary conditions and the method of images, all of which reappear here with current instead of charge.
- Hydrogeology: Groundwater Exploration and Pollution: aquifers, porosity and salinity, the targets most resistivity surveys in India are run for.
- Filters, Deconvolution and Fractal Analysis: the linear-filter idea used to compute sounding curves quickly.
The Hook: Two Readings, Two Different Questions
How CSIR NET asks it. Part C Geophysics: geometric factors of the standard arrays, apparent resistivity from field readings, two-layer behaviour and the reflection coefficient, sounding-curve types (H, K, A, Q), Dar Zarrouk parameters and equivalence, anisotropy, and when to choose profiling or sounding.
Resistivity of Earth Materials
Resistivity \( \rho \) (unit \( \Omega\,\text{m} \)) is the resistance of a unit cube; its reciprocal is the conductivity \( \sigma = 1/\rho \) (S/m). For a cylinder of length \( L \) and cross-section \( A \), \( R = \rho L/A \). Ohm’s law in a continuum is
$$\mathbf{J} = \sigma\mathbf{E}, \qquad \mathbf{E} = -\nabla V .$$Current flows in rocks in three ways:
| Mode | Carrier | Where it matters |
|---|---|---|
| Electronic | free electrons | metallic sulphides, graphite, native metals, magnetite |
| Electrolytic | ions in pore water | almost all sedimentary and weathered rocks, soils, aquifers |
| Dielectric | displacement of bound charges | only at high frequency (ground-penetrating radar range); negligible for DC |
Because most rock-forming silicates are near-insulators, the bulk resistivity of most rocks is controlled by the pore water: how much there is (porosity, saturation), how salty it is, and how well connected the pores are. Clay adds surface conduction along charged grain surfaces.
| Material | Typical behaviour |
|---|---|
| Sea water, saline groundwater | very low (well under 1 \( \Omega\,\text{m} \) for sea water) |
| Clay, shale | low |
| Fresh-water sand and gravel aquifer | intermediate |
| Dry sand, unweathered granite, basalt, quartzite | high to very high |
| Massive sulphides, graphite | very low (electronic conduction) |
Resistivities of earth materials span more than ten orders of magnitude, and the ranges of different rock types overlap widely. A single resistivity value never identifies a rock; the contrast with the surroundings does the work.
Archie’s law
For clean (clay-free) rocks, Archie’s empirical relations link resistivity to porosity \( \phi \) and water saturation \( S_w \):
$$\boxed{F = \frac{\rho_0}{\rho_w} = a\,\phi^{-m}}, \qquad \boxed{\rho_t = a\,\phi^{-m} S_w^{-n}\,\rho_w}$$Here \( F \) is the formation factor, \( \rho_0 \) the resistivity of the fully water-saturated rock, \( \rho_w \) the pore-water resistivity, \( m \) the cementation exponent and \( n \) the saturation exponent (commonly taken as about 2). The relation fails in clay-rich rocks, where surface conduction adds a term independent of \( \rho_w \). Archie’s law is used most in well logging, but it is also how a surface survey’s resistivity is turned into an estimate of groundwater salinity or porosity.
Anisotropy
A stack of thin layers with resistivities \( \rho_i \) and thicknesses \( h_i \) (total \( H \)) behaves, at scales much larger than the layers, like one uniform anisotropic layer:
$$\rho_\ell = \frac{H}{\sum h_i/\rho_i}\ \ (\text{parallel to bedding}), \qquad \rho_t = \frac{\sum h_i\rho_i}{H}\ \ (\text{across bedding}).$$These are the parallel and series resistor formulas. Always \( \rho_t \ge \rho_\ell \). Two derived quantities:
$$\lambda = \sqrt{\rho_t/\rho_\ell}\ \ (\text{coefficient of anisotropy}), \qquad \rho_m = \sqrt{\rho_t\rho_\ell}\ \ (\text{mean resistivity}).$$The Point Source: Where Every Formula Starts
In a homogeneous region with no sources, charge conservation \( \nabla\cdot\mathbf{J} = 0 \) and \( \mathbf{J} = -\sigma\nabla V \) give Laplace’s equation, \( \nabla^2 V = 0 \).
A current \( I \) injected at a point on the surface of a uniform half-space spreads out over hemispheres of area \( 2\pi r^2 \):
$$J = \frac{I}{2\pi r^2}, \qquad E = \rho J = \frac{\rho I}{2\pi r^2}, \qquad \boxed{V(r) = \frac{\rho I}{2\pi r}}$$(For a point source buried deep in a full space, the area is \( 4\pi r^2 \) and \( V = \rho I/4\pi r \).)
Four electrodes
Current \( +I \) enters at A and leaves at B; the voltage is measured between M and N. Adding the contributions of both current electrodes at both potential electrodes:
$$\Delta V = V_M - V_N = \frac{\rho I}{2\pi}\left[\frac{1}{AM} - \frac{1}{BM} - \frac{1}{AN} + \frac{1}{BN}\right].$$Over real, non-uniform ground we compute the same expression from the readings and call the result the apparent resistivity:
$$\boxed{\rho_a = K\,\frac{\Delta V}{I}}, \qquad K = \frac{2\pi}{\dfrac{1}{AM} - \dfrac{1}{BM} - \dfrac{1}{AN} + \dfrac{1}{BN}}$$\( K \) is the geometric factor (unit: metres). \( \rho_a \) equals the true resistivity only over uniform ground; otherwise it is a weighted average of the resistivities the current samples. By the reciprocity theorem, interchanging the current and potential electrode pairs leaves \( \rho_a \) unchanged.
The standard arrays
graph LR
subgraph W["Wenner: A-M-N-B, all gaps a"]
W1["K = 2πa"]
end
subgraph S["Schlumberger: AB = 2L, MN = 2l, l much less than L"]
S1["K = π(L² − l²)/2l ≈ πL²/2l"]
end
subgraph D["Dipole-dipole: dipoles a, gap na"]
D1["K = πn(n+1)(n+2)a"]
end| Array | Layout | Geometric factor \( K \) | Notes |
|---|---|---|---|
| Wenner | A–M–N–B, equal spacing \( a \) | \( 2\pi a \) | large signal; all four electrodes move for each new spacing |
| Schlumberger | MN small at the centre of AB; \( AB/2 = L \), \( MN/2 = l \) | \( \dfrac{\pi(L^2 - l^2)}{2l} \approx \dfrac{\pi L^2}{2l} \) | measures (nearly) the field \( E \) at the centre; only A and B move for most readings |
| Dipole-dipole | current dipole AB and potential dipole MN, each of length \( a \), inner ends \( na \) apart | \( \pi n(n+1)(n+2)a \) | good lateral resolution; small signal at large \( n \); standard for IP |
| Pole-dipole | B at “infinity” | \( 2\pi n(n+1)a \) | one remote electrode; stronger signal than dipole-dipole |
| Pole-pole | B and N at “infinity” | \( 2\pi a \) | largest signal, poorest resolution, picks up telluric noise |
Derivation check for Wenner: \( AM = a \), \( BM = 2a \), \( AN = 2a \), \( BN = a \); the bracket is \( 1/a \), so \( K = 2\pi a \).
How deep does the current go?
For two current electrodes a distance \( L \) apart on a uniform half-space, the fraction of the current that flows above a depth \( z \) (through the vertical plane midway between them) is
$$\frac{I_z}{I} = \frac{2}{\pi}\tan^{-1}\frac{2z}{L}.$$Half the current flows above \( z = L/2 \); about 70% above \( z = L \). So wider current electrodes push more current deeper, which is the whole basis of sounding. The depth actually “seen” also depends on the array and on the layering; for a conductive surface layer, much of the current stays trapped in it.
Profiling and Sounding
| Profiling (horizontal electrical profiling, constant separation traversing) | Sounding (vertical electrical sounding, VES) | |
|---|---|---|
| What is fixed | electrode spacing | array centre |
| What changes | position along a line | spacing, expanded step by step |
| Plot | \( \rho_a \) against distance | \( \log\rho_a \) against \( \log(AB/2) \) or \( \log a \) |
| Finds | lateral changes: dykes, faults, fracture zones, contacts, buried channels | layering: depth to bedrock, aquifer thickness, saline–fresh interface |
| Assumes | roughly constant depth sampled | ground horizontally layered under the spread (1-D) |
| Preferred array | Wenner, dipole-dipole, gradient | Schlumberger (or Wenner) |
Electrical resistivity tomography (ERT) combines the two: a multi-electrode cable takes readings at many spacings and positions, the data are plotted as a pseudosection (each reading placed below the array centre at a depth that increases with spacing), and a 2-D or 3-D inversion turns that into a model. A pseudosection is not a cross-section: its shapes are smeared, and the same body looks different with different arrays.
Why Schlumberger is the usual choice for VES
- Only the current electrodes move for most readings, so the survey is faster.
- The small potential dipole stays in one place, so lateral variations near M and N do not cause random jumps; when MN must be enlarged (signal too small), the curve shows a step that can be corrected.
- The Schlumberger \( \rho_a \) is (nearly) proportional to the electric field at the centre, which simplifies theory.
Wenner gives a larger voltage for the same current, which helps in noisy or high-contact-resistance ground, but all four electrodes move at every step and near-surface changes under any of them show up as noise on the curve.
Field practice
- Commutated DC or very low-frequency square waves are used, not steady DC, to cancel natural potentials and electrode polarisation.
- Non-polarisable electrodes (a metal in a saturated solution of its own salt, such as copper in copper sulphate) are used for potential measurements when accuracy matters, especially in IP.
- Noise sources: contact resistance, telluric currents, cultural noise (power lines, pipes, fences), leakage along wet cables.
Interpreting a Sounding
The two-layer case
A layer of resistivity \( \rho_1 \), thickness \( h \), over a half-space of resistivity \( \rho_2 \). At the interface, by analogy with optics, the source has images; the reflection coefficient is
$$\boxed{k = \frac{\rho_2 - \rho_1}{\rho_2 + \rho_1}}, \qquad -1 \le k \le 1 .$$The surface potential becomes an infinite series of images at depths \( 2nh \):
$$V(r) = \frac{\rho_1 I}{2\pi r}\left[1 + 2\sum_{n=1}^{\infty}\frac{k^n}{\sqrt{1 + (2nh/r)^2}}\right].$$For the Wenner array this gives
$$\frac{\rho_a}{\rho_1} = 1 + 4\sum_{n=1}^{\infty}k^n\left[\frac{1}{\sqrt{1 + (2nh/a)^2}} - \frac{1}{\sqrt{4 + (2nh/a)^2}}\right].$$Limiting checks. As \( a \to 0 \), every bracket tends to zero and \( \rho_a \to \rho_1 \). As \( a \to \infty \), every bracket tends to \( 1 - \tfrac{1}{2} = \tfrac{1}{2} \), so \( \rho_a/\rho_1 \to 1 + 2k/(1 - k) = (1 + k)/(1 - k) = \rho_2/\rho_1 \). The curve starts at \( \rho_1 \) and ends at \( \rho_2 \).
| Wenner spacing \( a \) (m) | 1 | 5 | 10 | 20 | 50 | 100 |
|---|---|---|---|---|---|---|
| \( \rho_a \) for \( \rho_1 = 100 \), \( \rho_2 = 10\ \Omega\,\text{m} \), \( h = 5 \) m | 99.6 | 73.4 | 33.9 | 12.9 | 10.2 | 10.0 |
| \( \rho_a \) for \( \rho_1 = 50 \), \( \rho_2 = 500\ \Omega\,\text{m} \), \( h = 10 \) m | 50.0 | 53.6 | 69.0 | 112.6 | 216.4 | 315.1 |
The second row climbs slowly: over a resistive basement the curve needs spacings many times the layer thickness to approach \( \rho_2 \) (at \( a = 500 \) m it is still only about 473). The first row drops quickly: current is drawn into a conductor easily.
Curve types for three layers
| Type | Resistivity order | Shape of \( \rho_a \) curve | Typical setting |
|---|---|---|---|
| H | \( \rho_1 > \rho_2 < \rho_3 \) | minimum (a bowl) | dry topsoil, saturated weathered zone, fresh bedrock (classic hard-rock aquifer) |
| K | \( \rho_1 < \rho_2 > \rho_3 \) | maximum (a hump) | resistive layer such as a sill, caliche or fresh-water lens between conductors |
| A | \( \rho_1 < \rho_2 < \rho_3 \) | rising steadily | resistivity increasing with depth |
| Q | \( \rho_1 > \rho_2 > \rho_3 \) | falling steadily | dry cover over saline water or clay |
Four-layer curves are named by the two overlapping three-layer types: HK, KH, HA, AK, QH and so on (for \( \rho_1 > \rho_2 < \rho_3 > \rho_4 \), the first three make H and the last three make K: type HK).
Dar Zarrouk parameters
For a layer of thickness \( h \) and resistivity \( \rho \):
$$\boxed{S = \frac{h}{\rho}\ \ (\text{longitudinal conductance, siemens})}, \qquad \boxed{T = h\rho\ \ (\text{transverse resistance, } \Omega\,\text{m}^2)}$$For a stack of layers, add them: \( S = \sum h_i/\rho_i \), \( T = \sum h_i\rho_i \). These are exactly the quantities in the anisotropy formulas: \( \rho_\ell = H/S \) and \( \rho_t = T/H \).
Asymptotic use of S. Over a perfectly insulating basement, current is confined to the layers above it and spreads in two dimensions. Then the late branch of a Schlumberger curve rises at 45° on log–log paper with
$$\rho_a = \frac{L}{S}\qquad (L = AB/2).$$So any point on that 45° line gives the total conductance of the cover: if \( \rho_a = 200\ \Omega\,\text{m} \) at \( AB/2 = 400 \) m on the 45° branch, then \( S = 400/200 = 2 \) S. (For Wenner over the same model, \( \rho_a = 2a\ln 2/S \approx 1.39\,a/S \).)
Equivalence and suppression: why VES is non-unique
Suppression. A thin layer whose resistivity lies between those of the layers above and below it (in A- and Q-type sections) may change the curve so little that it is not detected at all. It has to be thick to show.
Anisotropy and pseudo-anisotropy. A uniform anisotropic layer of thickness \( h \) appears in a sounding exactly like an isotropic layer of resistivity \( \rho_m = \sqrt{\rho_\ell\rho_t} \) and thickness \( \lambda h \). From surface DC data alone the two cannot be told apart, so depths to a basement below anisotropic rocks (shales, finely layered sediments) come out too large by the factor \( \lambda \).
From curve matching to inversion
- Curve matching. The field curve, on transparent log–log paper, is slid over theoretical master curves for two layers (with the reflection coefficient as parameter); multilayer curves are handled piece by piece with auxiliary point charts, replacing the upper layers by an equivalent single layer using the Dar Zarrouk rules. Log–log plotting means curves of the same shape but different scale differ only by a shift.
- Linear filtering. The surface potential over layered ground is a Hankel transform of a resistivity transform (kernel) that depends only on the layering. D. P. Ghosh showed that \( \rho_a \) can be computed from that transform by convolving it with a short digital filter, which made fast forward modelling, and hence computer inversion, practical.
- Inversion. A starting model is adjusted by (damped) least squares until the computed curve fits the data; 2-D and 3-D smoothness-constrained inversion is now routine for ERT. Equivalence does not go away: an inversion can only report the range of models that fit.
Profiling anomalies
- Vertical contact. A Wenner profile across a contact between rocks of different resistivity shows sharp discontinuities each time an electrode crosses the contact, so the curve has several cusps spread over a distance about equal to the array length.
- Conductive dyke or fracture zone. A resistivity low, narrower and sharper with smaller spacing; the shape depends on width and depth relative to the spacing.
- Resistive dyke (quartz reef, dolerite in conductive country rock). A high; very thin resistive bodies are hard to see because current goes round them.
- Using two spacings on the same line separates shallow from deeper causes: an anomaly that grows with the larger spacing comes from deeper down.
Memory Tricks
Don’t Confuse
| Pair | First | Second |
|---|---|---|
| Profiling vs sounding | fixed spacing, moving array: lateral change | fixed centre, expanding array: change with depth |
| True vs apparent resistivity | property of one material | \( K\Delta V/I \): a weighted average over what the current samples |
| \( \rho_\ell \) vs \( \rho_t \) | along bedding, parallel-resistor average, smaller | across bedding, series average, larger |
| S vs T | \( h/\rho \), siemens, controls thin conductors | \( h\rho \), \( \Omega\,\text{m}^2 \), controls thin resistors |
| Equivalence vs suppression | different layers, same curve (S or T fixed) | intermediate thin layer leaves no mark |
| H vs K curve | minimum: conductor sandwiched | maximum: resistor sandwiched |
| Pseudosection vs section | plotted data, depth only nominal | inverted model of true resistivity |
Common Mistakes
Practice
All questions below are original practice questions written for this page. They are not from any CSIR NET paper.
Level 1: Foundation
- What is the geometric factor of a Wenner array with spacing 15 m?
- Which sounding-curve type shows a minimum?
- Define longitudinal conductance and give its unit.
Answers
- \( K = 2\pi a = 30\pi \approx 94.2 \) m.
- H type (\( \rho_1 > \rho_2 < \rho_3 \)).
- \( S = h/\rho \), summed over layers; unit siemens.
Level 2: Part B Style
Practice Q1. A dipole-dipole array has dipole length 10 m and \( n = 3 \). Its geometric factor is closest to:
(a) 377 m (b) 754 m (c) 1,885 m (d) 3,770 m
Answer: (c) 1,885 m
\( K = \pi n(n+1)(n+2)a = \pi \times 3 \times 4 \times 5 \times 10 = 600\pi \approx 1{,}885 \) m. (a) is the pole-dipole factor for \( n = 2 \), \( 2\pi n(n+1)a = 120\pi \approx 377 \) m. (b) writes 2 in place of \( (n+2) \). (d) doubles the answer, as if \( 4\pi \) (full space) had been used in place of \( 2\pi \).
Practice Q2. Two current electrodes are 100 m apart on uniform ground. The fraction of the current flowing above a depth of 100 m is about:
(a) 0.30 (b) 0.50 (c) 0.70 (d) 0.90
Answer: (c) 0.70
\( I_z/I = (2/\pi)\tan^{-1}(2z/L) = (2/\pi)\tan^{-1}2 \approx 0.705 \). (b) is the value at \( z = L/2 = 50 \) m. (a) is the value at \( z = 25 \) m.
Practice Q3. A sequence of thin alternating beds, 2 m of 10 \( \Omega\,\text{m} \) and 2 m of 90 \( \Omega\,\text{m} \), is treated as one anisotropic layer. Its coefficient of anisotropy and mean resistivity are:
(a) \( \lambda = 1.67 \), \( \rho_m = 30\ \Omega\,\text{m} \) (b) \( \lambda = 3.0 \), \( \rho_m = 30\ \Omega\,\text{m} \) (c) \( \lambda = 1.67 \), \( \rho_m = 50\ \Omega\,\text{m} \) (d) \( \lambda = 2.78 \), \( \rho_m = 18\ \Omega\,\text{m} \)
Answer: (a)
\( S = 2/10 + 2/90 = 0.2222 \) S, so \( \rho_\ell = H/S = 4/0.2222 = 18\ \Omega\,\text{m} \). \( T = 20 + 180 = 200\ \Omega\,\text{m}^2 \), so \( \rho_t = T/H = 50\ \Omega\,\text{m} \). Then \( \lambda = \sqrt{50/18} \approx 1.67 \) and \( \rho_m = \sqrt{18 \times 50} = 30\ \Omega\,\text{m} \). (b) uses \( \sqrt{90/10} \). (c) quotes \( \rho_t \) as \( \rho_m \). (d) gives \( \rho_t/\rho_\ell \) without the square root and \( \rho_\ell \) as \( \rho_m \).
Practice Q4. On a Schlumberger sounding, the last five readings lie on a straight line rising at 45° on log–log paper, with \( \rho_a = 150\ \Omega\,\text{m} \) at \( AB/2 = 300 \) m. The most reasonable interpretation is:
(a) a resistive basement below cover of total longitudinal conductance about 2 S (b) a conductive basement at a depth of about 300 m (c) a cover of transverse resistance \( 45{,}000\ \Omega\,\text{m}^2 \) (d) a basement of resistivity 150 \( \Omega\,\text{m} \)
Answer: (a)
A 45° rising terminal branch means current is confined above an (effectively) insulating basement, and \( \rho_a = L/S \). So \( S = 300/150 = 2 \) S. (b) has the wrong sign of contrast. (c) multiplies \( L \) and \( \rho_a \); T controls K-type thin resistors, not this branch. (d) mistakes a point on a rising line for a plateau.
Level 3: Part C Style
Practice Q5. A Wenner sounding over a two-layer earth gives these apparent resistivities:
| \( a \) (m) | 1 | 5 | 10 | 20 | 50 | 100 |
|---|---|---|---|---|---|---|
| \( \rho_a \) (\( \Omega\,\text{m} \)) | 99.6 | 73.4 | 33.9 | 12.9 | 10.2 | 10.0 |
Which statements are correct?
- \( \rho_1 \approx 100\ \Omega\,\text{m} \) and \( \rho_2 \approx 10\ \Omega\,\text{m} \).
- The reflection coefficient at the interface is about \( -0.82 \).
- The first layer is a few metres thick, not tens of metres.
- The curve type is A.
(a) 1 and 2 only (b) 1, 2 and 3 only (c) 2, 3 and 4 only (d) 1 and 4 only
Answer: (b) 1, 2 and 3 only
- True. The short-spacing limit is \( \rho_1 \); the long-spacing asymptote is \( \rho_2 \).
- True. \( k = (10 - 100)/(10 + 100) = -0.818 \).
- True. The curve has already fallen to a third of \( \rho_1 \) at \( a = 10 \) m and is essentially at \( \rho_2 \) by \( a = 50 \) m, which places the interface at a few metres. (The table was computed for \( h = 5 \) m with the image series above.)
- False. A falling two-layer curve over a conductor is not an A type (A is rising and needs three layers); with two layers it is simply a descending curve.
Practice Q6. A VES over granite terrain is interpreted as: 2 m of 300 \( \Omega\,\text{m} \) topsoil, 4 m of 8 \( \Omega\,\text{m} \) weathered, saturated granite, then fresh granite at 3,000 \( \Omega\,\text{m} \). A second interpreter proposes a different model that fits the data equally well. Which alternative middle layer is most likely to be equivalent, and why?
(a) 6 m at 12 \( \Omega\,\text{m} \), because \( h/\rho \) is unchanged (b) 6 m at 5.3 \( \Omega\,\text{m} \), because \( h\rho \) is unchanged (c) 8 m at 8 \( \Omega\,\text{m} \), because \( \rho \) is unchanged (d) 4 m at 80 \( \Omega\,\text{m} \), because the basement controls the curve
Answer: (a)
The section is H type (300 > 8 < 3000). A thin conductive layer between resistors is resolved only through its longitudinal conductance: \( S = 4/8 = 0.5 \) S. Option (a) gives \( 6/12 = 0.5 \) S: S-equivalent. Option (b) keeps \( T = 32\ \Omega\,\text{m}^2 \), which is the rule for a thin resistor (K or Q type), not this case; its S is about 1.13 S. Option (c) doubles S. Option (d) cuts S tenfold and would change the curve’s minimum greatly. In practice, the hydrogeological consequence is that the aquifer thickness is uncertain unless its resistivity is constrained by a borehole or by water resistivity and Archie’s law.
Practice Q7. Which statements about electrical profiling and sounding are correct?
- Interchanging the current and potential electrodes of any four-electrode array leaves the apparent resistivity unchanged.
- Over vertical anisotropic beds, an array laid across strike measures the larger apparent resistivity.
- A thin layer of intermediate resistivity in a Q-type section may go undetected.
- Over a uniformly anisotropic layer, a VES gives the true layer thickness and \( \rho_m \).
(a) 1 and 3 only (b) 1, 2 and 3 only (c) 2 and 4 only (d) 1, 3 and 4 only
Answer: (a) 1 and 3 only
- True. Reciprocity.
- False. This is the paradox of anisotropy: across strike gives \( \rho_\ell \), the smaller value; along strike gives \( \rho_m \).
- True. Suppression: a thin intermediate layer in an A or Q section leaves little trace.
- False. The layer appears with resistivity \( \rho_m \) but thickness \( \lambda h \), so the thickness is overestimated.
Quick Revision Table
| Idea | Fact or formula |
|---|---|
| Point source, half-space | \( V = \rho I/2\pi r \); full space \( \rho I/4\pi r \) |
| Apparent resistivity | \( \rho_a = K\Delta V/I \), \( K = 2\pi/[1/AM - 1/BM - 1/AN + 1/BN] \) |
| Wenner | \( K = 2\pi a \) |
| Schlumberger | \( K = \pi(L^2 - l^2)/2l \approx \pi L^2/2l \) |
| Dipole-dipole | \( K = \pi n(n+1)(n+2)a \); pole-dipole \( 2\pi n(n+1)a \) |
| Current above depth \( z \) | \( (2/\pi)\tan^{-1}(2z/L) \); half above \( L/2 \) |
| Archie | \( F = \rho_0/\rho_w = a\phi^{-m} \); \( \rho_t = a\phi^{-m}S_w^{-n}\rho_w \) |
| Reflection coefficient | \( k = (\rho_2 - \rho_1)/(\rho_2 + \rho_1) \) |
| Two-layer limits | \( \rho_a \to \rho_1 \) (small spacing), \( \rho_2 \) (large spacing) |
| Curve types | H min, K max, A rising, Q falling |
| Dar Zarrouk | \( S = \sum h/\rho \), \( T = \sum h\rho \); \( \rho_\ell = H/S \), \( \rho_t = T/H \) |
| Insulating basement | Schlumberger 45° branch: \( \rho_a = L/S \) |
| Equivalence | thin conductor: S; thin resistor: T; intermediate thin layer: suppression |
| Anisotropy | \( \lambda = \sqrt{\rho_t/\rho_\ell} \), \( \rho_m = \sqrt{\rho_t\rho_\ell} \); apparent thickness \( \lambda h \) |
| Paradox of anisotropy | along strike \( \rho_m \), across strike \( \rho_\ell \) |
Key Takeaways
What’s Next
- Induced Polarization: the same electrodes, but now we watch how the voltage decays after the current is switched off.
- Mineral Exploration, Sampling and Evaluation: where electrical surveys sit in an exploration programme.
- Electrical and Electromagnetic Methods: back to the chapter overview.