Skip to content

Fluvial, Glacial, Aeolian, Coastal and Karst Processes

CSIR NET Earth Sciences Part C Physical Geography: stream power, hydraulic geometry, glacier flow, dune types, wave mechanics and karst solution.

  • 27 min read
  • Updated
On this page · 14 sections
  1. Prerequisites
  2. The Hook: One Formula, Five Agents
  3. Fluvial Processes
  4. Glacial Processes
  5. Aeolian Processes
  6. Coastal Processes
  7. Karst Processes
  8. Memory Tricks
  9. Don’t Confuse
  10. Common Mistakes
  11. Practice
  12. Quick Revision Table
  13. Key Takeaways
  14. What’s Next

Prerequisites

The Hook: One Formula, Five Agents

Fluvial Processes

Driving force: shear stress and stream power

For steady, uniform flow the downslope weight component of the water balances the friction at the bed. The mean bed shear stress is

$$\boxed{\tau_0 = \rho g R S}$$

where \( \rho \) is water density (1,000 kg m\(^{-3}\)), \( R \) the hydraulic radius (area / wetted perimeter; close to depth \( d \) in a wide channel) and \( S \) the energy slope (usually taken as the bed slope).

Stream power is the rate of energy loss per unit channel length, and unit stream power divides that by width:

$$\Omega = \rho g Q S \quad (\text{W m}^{-1}), \qquad \omega = \frac{\Omega}{w} = \tau_0 \bar{v} \quad (\text{W m}^{-2})$$

Stream power is the single best predictor of a river’s ability to erode bedrock and carry coarse load. Steep, confined mountain rivers have \( \omega \) of hundreds of W m\(^{-2}\); lowland alluvial rivers a few to a few tens.

Entrainment threshold. A grain of diameter \( D \) starts to move when the dimensionless Shields stress exceeds a critical value:

$$\theta = \frac{\tau_0}{(\rho_s - \rho) g D} \;\geq\; \theta_c \approx 0.03\text{–}0.06$$

For gravel a value of about 0.045 is common. Fine sand and silt break this simple rule because cohesion and the viscous sublayer matter, which is why the Hjulström curve has its minimum near fine sand.

Load

LoadCarried byTypical shareNote
Dissolvedsolutionlarge in humid, low-relief, carbonate basinsnot limited by flow strength
Suspended (wash load + suspended bed material)turbulenceusually the largest part of the total loadwash load is finer than the bed, so it is supply-limited
Bedloadrolling, sliding, saltationoften a small fraction, but controls channel formcapacity-limited; moves only above threshold

Competence is the largest grain a flow can move; capacity is the total load it can carry.

Hydraulic geometry (Leopold and Maddock, 1953)

Width, mean depth and mean velocity vary with discharge as power laws:

$$w = aQ^b, \qquad d = cQ^f, \qquad v = kQ^m$$

Because \( Q = w\,d\,v \), continuity demands

$$\boxed{b + f + m = 1, \qquad a\,c\,k = 1}$$
Setb (width)f (depth)m (velocity)Meaning
At a station (one cross-section, changing flow)about 0.26about 0.40about 0.34banks confine the flow: depth and velocity take up most of the increase
Downstream (at a fixed frequency of flow, e.g. mean annual)about 0.5about 0.4about 0.1channels widen most; velocity barely increases downstream

The near-constant downstream velocity surprises people: the slope falls downstream, but depth (and so hydraulic radius) rises and roughness falls, and the effects nearly cancel.

Channel adjustment: Lane’s balance

Lane (1955) expressed the qualitative equilibrium of an alluvial channel as

$$Q_s \, D_{50} \;\propto\; Q_w \, S$$

Sediment load times grain size balances water discharge times slope. Increase sediment supply (for example after deforestation or mining) and the channel aggrades and steepens; trap sediment behind a dam and the river below degrades (incises) because the “hungry water” has spare capacity.

Channel patterns

PatternSinuosityConditionsBars and features
Straightbelow about 1.1–1.3rare over long reaches; structural controlalternate bars; thalweg still wanders
Meanderingabove about 1.5 (the common cut-off)gentle slope, cohesive banks, suspended or mixed loadpoint bars, cut banks, oxbows, scroll bars
Braidedlow per channelsteep slope, high bedload, variable discharge, weak banksmid-channel bars, many shifting channels
Anastomosingvariable, multiple channelslow gradient, stable vegetated islands, cohesive banks, aggrading valleystable islands cut from the floodplain

Leopold and Wolman (1957) showed that, at a given discharge, braided rivers occupy steeper slopes than meandering ones, with a threshold slope that falls as discharge rises. Schumm’s classification by load type (suspended-load, mixed-load and bedload channels) links pattern to sediment: bedload channels are wide, shallow and straight or braided; suspended-load channels narrow, deep and sinuous.

Meander geometry. Meander wavelength is typically about 10–14 channel widths and the radius of curvature about 2–3 widths. Flow in a bend is helical: surface water moves toward the outer bank, near-bed water toward the inner bank, eroding the cut bank and building the point bar.

Longitudinal profile and drainage-basin scaling

Most graded rivers have a concave-up profile: slope falls downstream as discharge rises and grain size fines. Knickpoints (steps in the profile) mark rock-resistance changes, faults or base-level falls migrating upstream.

RelationFormMeaning
Hack’s law (1957)\( L \propto A^{h} \), \( h \approx 0.6 \)main-stream length grows faster than \( \sqrt{A} \): large basins are elongated
Flint’s law\( S = k_s A^{-\theta} \), \( \theta \approx 0.4\text{–}0.6 \)slope–area scaling; \( \theta \) is the concavity index, \( k_s \) the steepness index
Stream-power erosion law\( E = K A^m S^n \)in steady state (\( E = U \)) gives Flint’s law with \( \theta = m/n \); high \( k_s \) means fast uplift or hard rock
Stream-length gradient index (Hack, 1973)\( SL = (\Delta H / \Delta L) \cdot L \)anomalously high SL flags resistant rock or active faulting

These relations are the basis of the DEM-based tectonic geomorphology on Submarine Relief and DEM-Based Analysis.

Fluvial landforms

  • Erosional: V-shaped valleys, gorges, potholes, waterfalls and knickpoints, incised (entrenched) meanders, river terraces.
  • Depositional: floodplains, natural levees (coarser sediment dropped at the channel edge during overbank flow), point bars, crevasse splays, backswamps, alluvial fans (where a confined channel exits onto a plain; slope and grain size fall away from the apex), deltas.
  • Terraces: paired terraces (same height on both sides) suggest a pulse of vertical incision; unpaired terraces suggest slow incision while the river migrates laterally. Fill terraces are cut into valley-fill alluvium; strath terraces are bedrock benches with a thin alluvial veneer.

Delta classification (Galloway, 1975). A triangle of controls:

Dominant controlShapeStandard example
Riverelongate, bird-foot, distributaries with leveesMississippi
Wavearcuate or cuspate, smooth shoreline with beach ridgesNile (arcuate), São Francisco (cuspate)
Tideestuarine, funnel-shaped distributaries, tidal sand ridges and mangrove islandsGanga–Brahmaputra (Sundarbans) is usually placed toward this corner

Glacial Processes

Mass balance

A glacier gains mass in its accumulation zone (snowfall, avalanching) and loses it in its ablation zone (melting, sublimation, calving). The line separating them at the end of the melt season is the equilibrium-line altitude (ELA). The accumulation-area ratio \( \text{AAR} = A_{\text{acc}}/A_{\text{total}} \) is typically about 0.5–0.8 for a valley glacier in balance (0.6 is a common working value). A falling AAR, or a rising ELA, means negative mass balance and retreat.

Even a retreating glacier keeps flowing forward: retreat means ablation at the snout exceeds the supply of ice by flow, not that the ice moves uphill.

How ice moves

MechanismPhysicsWhere important
Internal deformation (creep)Glen’s flow law \( \dot{\varepsilon} = A\tau^n \), with \( n \approx 3 \)all glaciers; the only motion of a frozen-bed glacier
Basal slidingregelation (pressure melting on the upstream side of obstacles, refreezing downstream) and enhanced creep around larger obstacles; aided by meltwater at the bedwarm-based (temperate) glaciers
Bed deformationshearing of water-saturated till beneath the iceice streams and soft-bedded glaciers; surges

Because \( n \approx 3 \), strain rate rises with the cube of stress, so most shear is concentrated near the bed and surface velocity is close to the maximum. The basal shear stress of a glacier of thickness \( H \) on surface slope \( \alpha \) is

$$\boxed{\tau_b = \rho_i g H \sin\alpha}$$

with \( \rho_i \approx 900 \) kg m\(^{-3}\). Measured values cluster around 50–150 kPa, which is why ice is often approximated as a perfectly plastic material with a yield stress near 100 kPa: thin ice where the surface is steep, thick ice where it is gentle (\( H = \tau_0 / \rho_i g \sin\alpha \)).

Thermal regime.

  • Warm-based (temperate): base at the pressure-melting point; meltwater present; sliding, abrasion and plucking are active. Most Himalayan and Alpine valley glaciers are at least partly temperate.
  • Cold-based (polar): base frozen to the bed; no sliding; very little erosion. Cold-based ice can preserve delicate pre-existing landscapes beneath it.
  • Polythermal: cold margins, warm interior; common in the high Arctic and on large ice sheets.

Glacial erosion and landforms

Abrasion (debris-laden ice scratching the bed) makes striations, grooves and polish; plucking (quarrying) removes joint blocks, especially on the down-ice side of bedrock bumps where pressure drops and water refreezes.

Erosional formDescription
Cirque (corrie, cwm)armchair hollow at a valley head; tarn lake common
Arête and hornknife-edge ridge between two cirques; pyramidal peak where three or more meet
U-shaped (glacial) troughparabolic cross-profile; truncated spurs; overdeepened basins (ribbon lakes)
Hanging valleytributary trough left high above the main trough floor
Fjorddrowned glacial trough, often with a shallow threshold at its mouth
Roche moutonnéesmooth, striated stoss side facing up-ice; steep, plucked lee side down-ice
Crag and tailresistant crag with a tail of protected rock or till down-ice
Depositional formDescription
Tillunsorted, unstratified, angular-to-subrounded, striated clasts
Morainesterminal (end), recessional, lateral, medial (two laterals merge), ground
Drumlinstreamlined till hill: blunt end up-ice, tapered tail down-ice (the reverse of a roche moutonnée)
Erratictransported boulder of foreign lithology
Eskersinuous ridge of sorted sand and gravel from a subglacial or englacial meltwater tunnel
Kame, kame terraceice-contact stratified mounds and benches
Kettlehollow left by a buried, melted ice block
Outwash plain (sandur)braided proglacial meltwater deposits

The periglacial assemblage (permafrost, ice wedges, pingos, patterned ground, solifluction) is tabled under landforms and climate on Concepts, Historical and Process Geomorphology.

Aeolian Processes

Entrainment and transport

Wind moves sand when the friction (shear) velocity \( u_* = \sqrt{\tau/\rho_a} \) exceeds a threshold. Bagnold’s (1941) fluid threshold is

$$\boxed{u_{*t} = A\sqrt{\frac{\rho_s - \rho_a}{\rho_a}\, g\, D}}, \qquad A \approx 0.1$$

so the threshold rises with \( \sqrt{D} \) for sand. Very fine grains (silt and clay) need more wind than the formula predicts, because of cohesion and because they sit within the smooth viscous layer near the surface. The impact threshold (to keep saltation going once started) is lower, about 0.8 of the fluid threshold, because falling grains splash others into the air.

ModeGrain sizeBehaviour
Saltationfine to medium sandballistic hops, mostly within about a metre of the surface; most of the sand flux
Reptation and creepcoarse sand, granulesgrains nudged or rolled by saltation impacts
Suspensionsilt and clay (dust)carried high and far; forms loess downwind

Sand flux rises roughly with the cube of friction velocity (Bagnold), so a modest increase in wind speed above threshold greatly increases transport.

Erosional landforms

Deflation (removal of loose grains) produces deflation hollows and pans and leaves a lag of coarse clasts, desert pavement (reg, serir). Abrasion by saltating sand, concentrated near the ground, cuts ventifacts (faceted pebbles, dreikanter), yardangs (streamlined ridges elongated parallel to the wind) and undercut pedestal rocks. Wind is a strong transporter but a weak eroder of hard rock; running water shapes most desert relief.

Dunes

Dune type depends mainly on sand supply and wind directional variability, with vegetation as a third control.

DuneSand supplyWind regimeKey feature
Barchanlimitedunidirectionalcrescent; horns point downwind; slip face on the concave lee side
Transverseabundantunidirectionalridges perpendicular to the wind; barchanoid ridges between barchan and transverse
Linear (seif, longitudinal)moderatebidirectional (two wind modes at an angle)long ridges roughly parallel to the resultant wind
Starabundantmultidirectionalcentral peak with radiating arms; grows upward rather than migrating
Parabolicmoderate, with vegetationunidirectionalU-shape; arms point upwind, anchored by vegetation; common on coasts and semi-arid margins
Domelimitedstrong windslow, no slip face

Parabolic dunes are the trap: their arms point upwind, the reverse of a barchan.

Dune migration. A barchan advances at a speed inversely proportional to its height:

$$c \approx \frac{q}{H}$$

where \( q \) is the volumetric sand flux over the crest per unit width (m\(^3\) m\(^{-1}\) yr\(^{-1}\)) and \( H \) dune height. Small barchans overtake large ones.

Coastal Processes

Wave mechanics

Wind waves are described by height \( H \), period \( T \), length \( L \) and water depth \( h \). Linear (Airy) theory gives:

RegimeConditionSpeed \( c \)Length
Deep water\( h > L/2 \)\( c_0 = gT/2\pi \approx 1.56\,T \) m s\(^{-1}\)\( L_0 = gT^2/2\pi \approx 1.56\,T^2 \) m
Shallow water\( h < L/20 \)\( c = \sqrt{gh} \)\( L = cT \)
Intermediatebetweendepends on both \( T \) and \( h \)
  • Deep-water waves are dispersive (longer periods travel faster); shallow-water waves are not.
  • Wave energy per unit surface area is \( E = \tfrac{1}{8}\rho g H^2 \): doubling height quadruples energy.
  • Breaking occurs when \( H/h \approx 0.78 \) on a gentle beach (the breaker depth is about 1.3 times the wave height). Breaker types: spilling (gentle beaches), plunging (moderate), surging (steep).
  • Refraction: wave crests slow in shallow water and bend to become parallel to the depth contours, so energy converges on headlands and diverges in bays. Headlands are eroded, bays fill: coasts straighten with time.
  • Longshore drift: waves approaching obliquely drive a longshore current and a zig-zag swash–backwash path of beach material. It builds spits, bars and tombolos in the direction of drift.

Tides and coastal classification

Davies (1964) classed coasts by spring tidal range: microtidal (below 2 m), mesotidal (2–4 m) and macrotidal (above 4 m). Wave-dominated coasts with barrier islands are mostly micro- to mesotidal; tidal flats, estuaries and mangroves dominate macrotidal coasts (the Gulf of Khambhat is a macrotidal example in India).

Coasts are also classed by relative sea-level history: submergent coasts (rias, drowned river valleys; fjords, drowned glacial troughs; Dalmatian coasts, drowned folded ridges) and emergent coasts (raised beaches, marine terraces, uplifted wave-cut platforms).

Coastal landforms

ErosionalDepositional
Cliffs and wave-cut notchesBeaches, berms, beach ridges
Wave-cut (shore) platformsSpits (recurved at the tip), hooks
Sea caves → arches → stacks → stumps (the headland sequence)Bars, baymouth bars, lagoons behind them (Chilika is a lagoon behind a barrier spit)
Blowholes, geosTombolos (a bar joining an island to the mainland)
Barrier islands, cuspate forelands, tidal flats, salt marshes, mangroves

Beach profiles. Long, low swell builds a steep beach with a berm (the swell or “summer” profile). Short, steep storm waves move sand offshore into a bar, leaving a flatter beach (the storm or “winter” profile). In India the seasonal storm profile comes with the monsoon.

Shoreline retreat under sea-level rise: the Bruun rule

Bruun (1962) assumed that a beach keeps its equilibrium profile as sea level rises, so the profile shifts landward and upward, eroding the upper beach and depositing the sand offshore. Retreat \( R \) for a sea-level rise \( S \) is

$$\boxed{R = \frac{S\,L_*}{B + h_*}}$$

where \( L_* \) is the cross-shore width of the active profile to the closure depth \( h_* \) (beyond which sand barely moves) and \( B \) the berm or dune height. Since \( L_*/(B + h_*) \) is the inverse of the mean profile slope, often 1:50 to 1:100, retreat is commonly 50–100 times the sea-level rise. It ignores alongshore sediment budgets, so use it as a first estimate only.

Karst Processes

Chemistry of solution

Karst forms on soluble rock: mainly limestone and dolomite, also gypsum and halite. Carbonate solution needs carbonic acid:

$$\text{CO}_2 + \text{H}_2\text{O} \rightleftharpoons \text{H}_2\text{CO}_3, \qquad \text{CaCO}_3 + \text{H}_2\text{CO}_3 \rightleftharpoons \text{Ca}^{2+} + 2\,\text{HCO}_3^-$$
  • Solubility rises with the partial pressure of CO\(_2\). Soil air, enriched by root respiration and decay, carries tens of times more CO\(_2\) than the atmosphere, so most solution happens just below the soil (the epikarst).
  • CO\(_2\) is more soluble in cold water, so equilibrium calcite solubility is higher in the cold. But tropical karst is the most spectacular because warm, wet climates supply much more biogenic CO\(_2\) and water.
  • Mixing corrosion: mixing two waters, each saturated with calcite at a different CO\(_2\) pressure, gives an undersaturated mixture that can dissolve more rock. It helps explain cave formation deep in the phreatic zone.
  • Degassing of CO\(_2\) when cave water meets cave air reverses the reaction and precipitates calcite as speleothems.

Karst landforms

ScaleForms
Small (surface)karren (lapies): solution flutes, runnels, grikes (widened joints) and clints (blocks between them) forming limestone pavement
Closed depressionsdolines (sinkholes): solution, collapse, subsidence (cover) types; uvalas (coalesced dolines); poljes (large flat-floored depressions, often fault-bounded, seasonally flooded)
Drainageswallow holes (ponors), sinking streams, dry valleys, blind valleys, resurgences (springs); little surface drainage, so drainage density is low
Undergroundcaves (phreatic tubes formed below the water table; vadose canyons cut above it), speleothems: stalactites (hanging), stalagmites (rising), columns, flowstone
Residual (tropical)cone (cockpit) karst, tower karst (steep isolated limestone towers on an alluvial plain, as in southern China)

Indian examples include the cave systems of Meghalaya, the Borra Caves in the Eastern Ghats of Andhra Pradesh and Kotumsar Cave in the Kanger Valley of Chhattisgarh.

Karst denudation rate

If water leaving a karst area carries a dissolved CaCO\(_3\) concentration \( C \) (mg L\(^{-1}\)) and the annual runoff depth is \( R \) (m yr\(^{-1}\)), each square metre loses \( R \times 1000 \times C \) mg = \( RC \) g of rock per year. Dividing by rock density (2.7 \( \times 10^6 \) g m\(^{-3}\)):

$$\boxed{\text{lowering rate (m yr}^{-1}) = \frac{R\,C}{2.7\times10^{6}}}$$

(an approach associated with Corbel and refined by later workers). Runoff matters more than temperature: wet climates dissolve limestone fastest.

Memory Tricks

Don’t Confuse

ThisvsThat
Competence: largest grain movedCapacity: total load carried
At-a-station hydraulic geometry (depth and velocity rise most)Downstream hydraulic geometry (width rises most)
Braided: steep, bedload, unstable barsAnastomosing: gentle, stable vegetated islands
Paired terraces: rapid vertical incisionUnpaired terraces: slow incision with lateral migration
Warm-based glacier: slides and erodesCold-based glacier: frozen bed, preserves the surface
Glacier retreat: snout ablation exceeds supplyIce flow: always downslope, even during retreat
Esker: sinuous ridge, sorted, subglacial tunnelMoraine: till ridge, unsorted, ice margin
Barchan: horns downwind, limited sandParabolic: arms upwind, vegetation
Deep-water wave: speed depends on periodShallow-water wave: speed depends on depth only
Swell (summer) profile: berm, steep beachStorm (winter) profile: offshore bar, flat beach
Stalactite: hangs from the roofStalagmite: grows up from the floor
Doline: small closed depressionPolje: large flat-floored, often fault-bounded depression

Common Mistakes

Practice

All questions below are original practice questions written for this page. They are not from any CSIR NET paper.

Level 1: Foundation

  1. Write the expression for mean bed shear stress in a river.
  2. Which side of a roche moutonnée faces up-ice?
  3. Which dune type forms under multidirectional winds with abundant sand?
Answers
  1. \( \tau_0 = \rho g R S \): density × gravity × hydraulic radius × slope.
  2. The smooth, gently sloping, striated stoss side faces up-ice; the steep plucked lee side faces down-ice.
  3. Star dunes.

Level 2: Part B Style

Practice Q1. At a gauging station \( w \propto Q^{0.24} \) and \( d \propto Q^{0.42} \). The velocity exponent \( m \) and the factor by which velocity increases when discharge doubles are:

(a) 0.34, 1.27 (b) 0.34, 1.34 (c) 0.66, 1.58 (d) 0.24, 1.18

Answer: (a) 0.34, 1.27

\( m = 1 - 0.24 - 0.42 = 0.34 \). Velocity increases by \( 2^{0.34} = 1.27 \). Option (b) confuses the exponent with the factor; (c) forgets that b and f both come off; (d) uses the width exponent.

Practice Q2. A sinuous, unsorted till ridge running along the valley side, and a sinuous ridge of stratified gravel running down the valley floor, are respectively:

(a) esker and lateral moraine (b) lateral moraine and esker (c) drumlin and kame (d) medial moraine and outwash

Answer: (b)

Unsorted till along the valley side is a lateral moraine. Stratified, sorted gravel in a sinuous ridge is an esker, deposited by a meltwater tunnel. Sorting is the discriminator: ice deposits are unsorted; meltwater deposits are sorted.

Practice Q3. Deep-water swell has a period of 8 s. Its wavelength and the depth below which it starts to “feel bottom” are about:

(a) 12.5 m, 6 m (b) 100 m, 50 m (c) 100 m, 5 m (d) 50 m, 100 m

Answer: (b) 100 m, 50 m

\( L_0 = 1.56 \times 64 = 99.9 \approx 100 \) m. The wave interacts with the bed once \( h < L/2 = 50 \) m. Option (a) gives the speed (12.5 m s\(^{-1}\)) as a length; (c) gives the shallow-water limit \( L/20 \).

Practice Q4. Upstream of a new dam a river aggrades; downstream it incises its bed and coarsens it. This is best explained by:

(a) Playfair’s law (b) Lane’s balance (c) Hack’s law (d) the Bruun rule

Answer: (b) Lane's balance

The dam traps sediment, so \( Q_s D_{50} \) falls below \( Q_w S \) downstream: the clear water has spare capacity and degrades the bed, winnowing fines. Upstream, the backwater lowers slope and the river drops its load. Hack’s law relates stream length to basin area; the Bruun rule is about shoreline retreat.

Level 3: Part C Style

Practice Q5. A temperate valley glacier has a surface slope of 2.5°. Assume perfectly plastic ice with yield stress 100 kPa and \( \rho_i = 900 \) kg m\(^{-3}\). Which statements are correct?

  1. The predicted ice thickness is about 260 m.
  2. Where the slope steepens to 5°, the predicted thickness is about half.
  3. Since the bed is at the pressure-melting point, basal sliding and plucking are likely.
  4. If the ELA rises, the glacier will flow backward up-valley.

(a) 1 and 3 only (b) 1, 2 and 3 only (c) 2 and 4 only (d) 1, 2, 3 and 4

Answer: (b) 1, 2 and 3 only
  • 1 true: \( H = 10^5/(900 \times 9.81 \times \sin 2.5°) = 10^5/385.1 = 260 \) m.
  • 2 true: \( \sin 5°/\sin 2.5° = 1.997 \), so the thickness about halves (130 m).
  • 3 true: a temperate base has meltwater, so sliding, abrasion and plucking operate.
  • 4 false: a rising ELA means negative mass balance and terminus retreat, but ice still flows down-glacier.

Practice Q6. A gravel-bed river 40 m wide, 1.5 m deep, slope 0.004, discharge 120 m\(^3\) s\(^{-1}\). Take \( R \approx d \), \( \theta_c = 0.045 \), \( \rho_s - \rho = 1{,}650 \) kg m\(^{-3}\). Which statements are correct?

  1. Bed shear stress is about 59 Pa.
  2. Unit stream power is about 118 W m\(^{-2}\).
  3. It can entrain grains up to about 80 mm.
  4. Doubling the depth at the same slope doubles the largest movable grain.

(a) 1, 2 and 3 only (b) 1, 2, 3 and 4 (c) 1 and 4 only (d) 2 and 3 only

Answer: (b) 1, 2, 3 and 4
  • 1 true: \( \tau_0 = 1000 \times 9.81 \times 1.5 \times 0.004 = 58.9 \) Pa.
  • 2 true: \( \omega = \rho g Q S / w = 1000 \times 9.81 \times 120 \times 0.004/40 = 117.7 \) W m\(^{-2}\).
  • 3 true: \( D = 58.86/(0.045 \times 1650 \times 9.81) = 0.081 \) m ≈ 80 mm.
  • 4 true: \( D_{\max} \propto \tau_0 \propto d \) at fixed slope, so it doubles.

Practice Q7. Two limestone regions are compared:

RegionRunoff (mm yr\(^{-1}\))Mean dissolved CaCO\(_3\) (mg L\(^{-1}\))
X (humid tropical)1,200150
Y (semi-arid)200250

Which statements are correct (rock density 2.7 g cm\(^{-3}\))?

  1. X is lowered at about 67 mm per thousand years.
  2. Y is lowered at about 19 mm per thousand years.
  3. Y’s water is harder, so Y is denuded faster.
  4. Runoff is the main reason for the difference.

(a) 1, 2 and 4 only (b) 1 and 3 only (c) 2 and 3 only (d) 1, 2, 3 and 4

Answer: (a) 1, 2 and 4 only
  • 1 true: \( 1.2 \times 150/2.7\times10^6 = 6.67\times10^{-5} \) m yr\(^{-1}\) = 67 mm kyr\(^{-1}\).
  • 2 true: \( 0.2 \times 250/2.7\times10^6 = 1.85\times10^{-5} \) m yr\(^{-1}\) = 19 mm kyr\(^{-1}\).
  • 3 false: harder water but six times less runoff; X is lowered about 3.6 times faster.
  • 4 true: runoff varies sixfold, concentration less than twofold.

Quick Revision Table

IdeaFact
Bed shear stress\( \tau_0 = \rho g R S \)
Stream power\( \Omega = \rho g Q S \); \( \omega = \Omega/w \)
Shields\( \theta_c \approx 0.03\text{–}0.06 \) (0.045 for gravel)
Hydraulic geometry\( b + f + m = 1 \); at a station 0.26/0.40/0.34; downstream 0.5/0.4/0.1
Lane (1955)\( Q_s D_{50} \propto Q_w S \)
Channel patternsstraight, meandering (sinuosity ≥ 1.5), braided (steep, bedload), anastomosing (stable islands)
Meanderswavelength 10–14 widths; radius 2–3 widths; helical flow
Hack’s law\( L \propto A^{0.6} \)
Flint’s law / stream-power\( S = k_s A^{-\theta} \); \( E = KA^mS^n \); \( \theta = m/n \)
Deltas (Galloway)river (bird-foot), wave (arcuate, cuspate), tide (estuarine)
Glacier stress\( \tau_b = \rho_i g H \sin\alpha \); 50–150 kPa; plastic about 100 kPa
Glen’s law\( \dot\varepsilon = A\tau^n \), \( n \approx 3 \)
AARabout 0.5–0.8 in balance
Bagnold threshold\( u_{*t} = A\sqrt{(\rho_s - \rho_a)gD/\rho_a} \), \( A \approx 0.1 \); flux ∝ \( u_*^3 \)
Dunesbarchan (horns downwind), transverse, linear (bidirectional), star (multidirectional), parabolic (arms upwind)
Barchan speed\( c \approx q/H \)
Deep-water waves\( c_0 = 1.56T \); \( L_0 = 1.56T^2 \); \( h > L/2 \)
Shallow-water waves\( c = \sqrt{gh} \); \( h < L/20 \)
Wave energy, breaking\( E = \rho g H^2/8 \); \( H/h \approx 0.78 \)
Tidal range (Davies)micro < 2 m, meso 2–4 m, macro > 4 m
Bruun rule\( R = S L_*/(B + h_*) \)
Karstsoil CO\(_2\); mixing corrosion; lowering = \( RC/2.7\times10^6 \) m yr\(^{-1}\)

Key Takeaways

What’s Next