Submarine Relief and DEM-Based Analysis
CSIR NET Earth Sciences Part C Physical Geography: continental margins, ridges, trenches, canyons, bathymetry, DEM sources, slope, D8 flow, morphometry.
- 20 min
On this page · 11 sections
Prerequisites
- The ocean-floor provinces from Part B: Ocean Floor and Sea Water.
- The geological view of the same features: Ocean Floor Morphology, Oceanic Crust and Vents.
- Sea-floor spreading and plate boundaries, which explain most large submarine relief: Paleomagnetism, Sea-Floor Spreading and Plate Tectonics.
- Remote-sensing platforms, stereo imaging and GIS data models: Remote Sensing, GIS, Photogrammetry and GPS.
- Stream power, Hack’s law and Flint’s law: Fluvial, Glacial, Aeolian, Coastal and Karst Processes.
The Hook: A Map Made from Sound and Radar
Submarine Relief
The two-level Earth
Earth’s hypsometric curve is bimodal: one peak near sea level (continents, mean land elevation about 0.8 km) and one at about 4–5 km depth (ocean basins, mean ocean depth about 3.7 km). The two levels reflect two kinds of crust: thick, light, old continental crust and thin, dense, young oceanic crust floating isostatically at different heights. About 29% of the surface is land and about 71% ocean.
Provinces of the ocean floor
| Province | Depth and gradient | Description |
|---|---|---|
| Continental shelf | to the shelf break, typically 100–200 m deep; gradient about 0.1° (about 1:1,000) | submerged continental crust; drowned river valleys, relict Pleistocene beach and dune sands; wide on passive margins, narrow on active margins |
| Continental slope | from the shelf break to about 2–3 km; typically a few degrees (about 2–5°) | the edge of continental crust; cut by submarine canyons; slumps and slides |
| Continental rise | about 2–4 km; gentle | apron of sediment from turbidity currents and contour currents (contourites) at the foot of the slope; present on passive margins, absent where a trench takes its place |
| Abyssal plain | about 3–6 km; gradient below about 1:1,000 | the flattest surfaces on Earth: turbidites and pelagic sediment burying older relief |
| Abyssal hills | rising up to a few hundred metres above the floor | faulted volcanic crust not buried by sediment; by area the most widespread landform on the planet |
| Mid-ocean ridge | crest about 2.5 km deep | a continuous volcanic mountain system along divergent boundaries, offset by transform faults and their inactive extensions, fracture zones |
| Trench | the deepest parts of the ocean, reaching about 11 km (Challenger Deep, Mariana Trench) | narrow, asymmetric troughs at subduction zones |
| Seamounts, guyots | rising 1 km or more from the floor | isolated volcanoes; guyots are flat-topped |
Active vs passive margins. A passive (Atlantic-type) margin lies within a plate: wide shelf, gentle slope, thick rise. An active (Pacific-type) margin coincides with a plate boundary: narrow shelf, steep slope, a trench instead of a rise, earthquakes and volcanoes. India’s margins are passive; the western continental shelf is markedly wider than the eastern one.
Ridge morphology and the depth–age relation
Ridge-axis relief depends on spreading rate:
| Spreading | Axis form | Example |
|---|---|---|
| Fast | smooth, broad axial high, low relief flanks | East Pacific Rise |
| Slow | deep axial rift valley (median valley) with rugged faulted flanks | Mid-Atlantic Ridge, Carlsberg Ridge |
| Ultraslow | discontinuous volcanism, exposed mantle rocks | Southwest Indian Ridge, Gakkel Ridge |
Away from the axis, the lithosphere cools, contracts and subsides. For ages up to roughly 70 Myr the depth follows the half-space cooling law (Parsons and Sclater, 1977):
$$\boxed{d(t) \approx 2500 + 350\sqrt{t}}$$with \( d \) in metres and \( t \) in Myr. Older floor flattens (the plate model). This is why ridges stand high and why old ocean basins are deep.
Features built on the ocean floor
- Seamounts are intraplate or near-ridge volcanoes. A guyot (named by H. H. Hess) is a seamount whose top was planed by waves at sea level and then carried down as the plate subsided with age.
- Atolls follow Darwin’s subsidence sequence: fringing reef around a volcanic island → barrier reef separated by a lagoon as the island subsides → atoll once the island has sunk below the surface while the reef grows upward. Deep drilling on Pacific atolls in the mid-twentieth century reached volcanic rock beneath more than a kilometre of shallow-water limestone, confirming the model. The Lakshadweep islands are atolls on the Chagos–Laccadive Ridge.
- Aseismic ridges are linear, seismically quiet ridges built by hotspots as plates moved over them: the Ninetyeast Ridge (Kerguelen hotspot) and the Chagos–Laccadive Ridge (Réunion hotspot) in the Indian Ocean.
- Oceanic plateaus are thick piles of basalt from large igneous provinces (Kerguelen Plateau, Ontong Java Plateau).
Canyons, channels and fans
Submarine canyons cut the continental shelf and slope. Their heads are often opposite river mouths, and many were extended by river erosion when sea level stood about 120 m lower during glacial maxima. Their lower parts are cut and maintained by turbidity currents: dense, sediment-laden flows that run downslope under gravity. The 1929 Grand Banks earthquake set off a turbidity current whose speed was later estimated from the sequence in which it broke submarine telegraph cables.
Turbidity currents leave canyons through leveed submarine channels and build deep-sea fans. The Bengal Fan, fed by the Ganga–Brahmaputra through the Swatch of No Ground canyon, is the largest submarine fan on Earth; the Indus Fan in the Arabian Sea is another of the world’s largest.
Mapping the sea floor
| Method | Principle | Note |
|---|---|---|
| Single-beam echo sounder | depth \( d = v\,t/2 \) from the two-way travel time \( t \) of a sound pulse; \( v \approx 1{,}500 \) m s\(^{-1}\) | sound speed varies (about 1,450–1,550 m s\(^{-1}\)) with temperature, salinity and pressure, so profiles are corrected |
| Multibeam (swath) echo sounder | a fan of beams measures a strip of depths at once | swath width \( W = 2d\tan(\theta/2) \) for a total fan angle \( \theta \); widens with depth |
| Side-scan sonar | records backscatter strength along the sides of a towed fish | images texture and objects, not accurate depth |
| Satellite altimetry | the sea surface bulges over seamounts and sags over trenches because of their gravity | gives global predicted bathymetry at kilometre-scale resolution; fills gaps between ship tracks |
| Airborne bathymetric LiDAR | green laser penetrates clear shallow water | coastal shallows only |
Global compilations such as GEBCO combine all of these into gridded bathymetry, which is itself a DEM.
DEM-Based Analysis
What a DEM is
A digital elevation model is a digital representation of surface height. Usage of the terms varies, but in most texts:
| Term | Meaning |
|---|---|
| DEM | generic: heights of a surface, usually on a regular grid |
| DSM (digital surface model) | top of everything: canopy, buildings |
| DTM (digital terrain model) | bare ground, with vegetation and buildings removed; sometimes includes breaklines and other terrain features |
Data structures: a raster grid (one height per cell; simple, the standard for analysis), a TIN (triangulated irregular network; variable density, follows breaklines), and contours (the traditional map form, interpolated to grids).
Sources
| Source | Method | Notes |
|---|---|---|
| SRTM (Shuttle Radar Topography Mission, February 2000) | C-band radar interferometry (InSAR) | about 60° N to 56° S; 1 arc-second (about 30 m) and 3 arc-second (about 90 m) grids; a surface model in forests |
| ASTER GDEM | optical stereo from the ASTER sensor | 1 arc-second grid; artefacts in cloudy areas |
| CartoDEM | optical stereo from ISRO’s Cartosat-1 | Indian national DEM, distributed through Bhuvan |
| ALOS World 3D | optical stereo (PRISM) | about 30 m global product |
| TanDEM-X | bistatic X-band InSAR | about 12 m and coarser global products |
| LiDAR | laser ranging from aircraft or drones; multiple returns allow a bare-earth DTM under vegetation | sub-metre resolution; local coverage |
| Photogrammetry and structure-from-motion | overlapping photographs from aircraft or drones | centimetre to metre resolution |
Pixel size from arc-seconds. One arc-second of latitude is about \( 6{,}371{,}000 \times \pi/648{,}000 \approx 30.9 \) m everywhere; one arc-second of longitude is \( 30.9\cos\varphi \) m at latitude \( \varphi \). Geographic-coordinate DEMs therefore have rectangular, not square, cells away from the equator, and must be projected (or corrected) before slope is computed.
Accuracy is reported as the root-mean-square error of DEM heights against check points:
$$\text{RMSE} = \sqrt{\frac{1}{n}\sum (z_{\text{DEM}} - z_{\text{ref}})^2}$$The mean error (bias) and RMSE differ: a DEM can have zero mean error and still a large RMSE. Errors grow on steep slopes, in forests (radar and optical DEMs see the canopy), in shadow, and in voids filled by interpolation.
Resolution matters. Coarser cells smooth the terrain: computed slopes become gentler, small valleys and ridges vanish, and drainage density falls. Always state the resolution when quoting a DEM-derived slope.
Primary terrain attributes
For a 3 × 3 window of cell size \( \Delta \), with the central cell \( z_5 \) and neighbours labelled
| \( z_1 \) (NW) | \( z_2 \) (N) | \( z_3 \) (NE) |
| \( z_4 \) (W) | \( z_5 \) | \( z_6 \) (E) |
| \( z_7 \) (SW) | \( z_8 \) (S) | \( z_9 \) (SE) |
the simplest (second-order finite difference) gradients are
$$\frac{\partial z}{\partial x} = \frac{z_6 - z_4}{2\Delta}, \qquad \frac{\partial z}{\partial y} = \frac{z_2 - z_8}{2\Delta}$$$$\boxed{\tan\beta = \sqrt{\left(\frac{\partial z}{\partial x}\right)^2 + \left(\frac{\partial z}{\partial y}\right)^2}}$$(Horn’s method, used in many GIS packages, weights all eight neighbours, but the idea is the same.)
| Attribute | Meaning | Use |
|---|---|---|
| Slope | magnitude of the gradient (degrees or percent; percent = 100 tan β) | landslide susceptibility, erosion, soil depth |
| Aspect | compass direction the slope faces (direction of steepest descent) | insolation, snowmelt, vegetation |
| Profile curvature | curvature in the downslope direction | flow acceleration (convex) or deceleration and deposition (concave) |
| Plan curvature | curvature across the slope | flow divergence (spurs) or convergence (hollows) |
| Hillshade | simulated illumination, commonly from azimuth 315° and altitude 45° | visual interpretation of lineaments and landforms |
| Relief, roughness | range or standard deviation of height within a window | landscape classification |
Hydrological analysis
graph TD
A["Raw DEM"] --> B["Fill sinks (pits)"]
B --> C["Flow direction (D8)"]
C --> D["Flow accumulation"]
D --> E["Stream network: cells above a threshold area"]
E --> F["Stream order (Strahler)"]
C --> G["Watershed delineation from a pour point"]
E --> H["Longitudinal profiles, slope-area, SL index, ksn"]
G --> I["Basin morphometry, hypsometric integral"]- Sink (pit) filling. Single-cell depressions, mostly artefacts, would trap flow; they are filled to the level of their lowest outlet. Real depressions (karst, glacial kettles) need care.
- Flow direction, D8. Each cell drains to the one of its eight neighbours with the steepest downward slope, where slope = drop/distance and the distance to a diagonal neighbour is \( \sqrt 2\,\Delta \). Multiple-flow-direction and D-infinity methods spread flow among neighbours and model divergent hillslopes better.
- Flow accumulation. The number of upstream cells draining through each cell; × cell area = contributing (drainage) area.
- Stream extraction. Cells whose contributing area exceeds a threshold are channels. A smaller threshold gives a denser network: drainage density is partly an analyst’s choice, so it should be calibrated against field or image evidence.
- Watersheds are traced upstream from a pour point.
Compound indices.
- Topographic wetness index (Beven and Kirkby’s TOPMODEL): \( \text{TWI} = \ln(a/\tan\beta) \), where \( a \) is the specific catchment area (contributing area per unit contour width). High in flat hollows with large upslope areas: where saturation-excess runoff starts.
- Stream power index: \( \text{SPI} = a\tan\beta \). High where large flows run down steep slopes: gully and channel-head sites.
Basin morphometry from a DEM
| Index | Formula | Interpretation |
|---|---|---|
| Drainage density | \( D_d = \Sigma L/A \) | high on impermeable, sparsely vegetated, weak rocks |
| Bifurcation ratio | \( R_b = N_u/N_{u+1} \) | usually about 3–5; higher where structure elongates the basin |
| Elongation ratio (Schumm) | \( R_e = (2/L)\sqrt{A/\pi} \) | 1 for a circle; lower for elongated basins |
| Circularity ratio | \( R_c = 4\pi A/P^2 \) | 1 for a circle |
| Form factor (Horton) | \( R_f = A/L^2 \) | low for elongated basins, which have flatter, longer hydrographs |
| Hypsometric integral | \( (\bar z - z_{\min})/(z_{\max} - z_{\min}) \) | upland volume remaining; high in uplifting or resistant terrain |
Tectonic geomorphology from DEMs
| Index | Formula | Active tectonics indicated by |
|---|---|---|
| Mountain-front sinuosity | \( S_{mf} = L_{mf}/L_s \) (front length along its foot / straight-line length) | low values (near 1; below about 1.4): straight fronts held by active faults |
| Valley floor width-to-height ratio (Bull and McFadden) | \( V_f = \dfrac{2V_{fw}}{(E_{ld} - E_{sc}) + (E_{rd} - E_{sc})} \) | low values (below about 1): narrow V-shaped valleys incising in response to uplift |
| Asymmetry factor | \( AF = 100\,A_r/A_t \) (\( A_r \): basin area right of the trunk stream facing downstream) | values far from 50: tilting |
| Stream-length gradient index | \( SL = (\Delta H/\Delta L)\,L \) | anomalously high values: uplift or resistant rock |
| Normalised steepness | \( k_{sn} = S\,A^{\theta_{ref}} \) with a fixed reference concavity (often 0.45) | high \( k_{sn} \): fast uplift or hard rock; knickpoints where it jumps |
| χ (chi) analysis | integral of \( A^{-\theta} \) along the channel | a channel plotted against χ is straight in steady state; mismatched χ across a divide suggests divide migration |
These indices are always read together with lithology: hard rock mimics uplift.
Memory Tricks
Don’t Confuse
| This | vs | That |
|---|---|---|
| Continental rise: sediment apron (passive margin) | Trench: subduction trough (active margin) | |
| Transform fault: active, between ridge segments | Fracture zone: inactive scar beyond the ridge offset | |
| Guyot: flat-topped, wave-planed, then subsided | Seamount: peaked volcano never planed | |
| Aseismic ridge (Ninetyeast): hotspot track | Mid-ocean ridge: spreading axis, seismically active | |
| Multibeam echo sounder: depth | Side-scan sonar: backscatter image, not depth | |
| DSM: canopy and buildings | DTM: bare ground | |
| Bias (mean error) | RMSE (total error magnitude) | |
| Profile curvature: along the flow line | Plan curvature: across the slope (convergence and divergence) | |
| D8: one steepest neighbour | Multiple-flow-direction / D-infinity: flow split among neighbours |
Common Mistakes
Practice
All questions below are original practice questions written for this page. They are not from any CSIR NET paper.
Level 1: Foundation
- Which margin province is typically absent where a trench lies at the foot of the slope?
- What is a guyot?
- In the D8 algorithm, to how many neighbours does a cell send flow?
Answers
- The continental rise.
- A flat-topped seamount, planed by waves at sea level and since carried below it by subsidence.
- One: the neighbour with the steepest downward slope.
Level 2: Part B Style
Practice Q1. The depth to ocean floor of age 36 Myr, from \( d = 2500 + 350\sqrt t \), is:
(a) 2,850 m (b) 4,600 m (c) 5,300 m (d) 15,100 m
Answer: (b) 4,600 m
\( 2500 + 350 \times 6 = 4{,}600 \) m. (a) takes \( \sqrt{t} \) as 1; (d) forgets the square root (\( 2500 + 350 \times 36 \)).
Practice Q2. A multibeam system with a total fan angle of 120° surveys a 3,000 m deep basin. The swath width is about:
(a) 3.5 km (b) 5.2 km (c) 10.4 km (d) 20.8 km
Answer: (c) 10.4 km
\( W = 2d\tan(\theta/2) = 2 \times 3000 \times \tan 60° = 6000 \times 1.732 = 10{,}392 \) m. (b) uses the half-width only; (a) uses \( \tan 30° \) (\( 2 \times 3000 \times 0.577 \)).
Practice Q3. An SRTM 1 arc-second DEM is used at 23.5° N. The approximate east–west cell size is:
(a) 30.9 m (b) 28.3 m (c) 12.3 m (d) 90 m
Answer: (b) 28.3 m
\( 30.9 \times \cos 23.5° = 30.9 \times 0.917 = 28.3 \) m. (a) is the north–south size; (d) is the 3 arc-second product.
Practice Q4. A basin outlined from a 30 m DEM drains 5,000 cells. Its contributing area is:
(a) 0.15 km\(^2\) (b) 1.5 km\(^2\) (c) 4.5 km\(^2\) (d) 45 km\(^2\)
Answer: (c) 4.5 km²
Each cell is 30 × 30 = 900 m\(^2\); \( 5000 \times 900 = 4.5\times10^6 \) m\(^2\) = 4.5 km\(^2\). (a) multiplies by 30 instead of 900.
Level 3: Part C Style
Practice Q5. A DEM is checked at eight GPS points; the errors (DEM minus GPS, m) are +1.5, −2.0, +3.0, −1.0, +0.5, +2.5, −3.5, +1.0. Which statements are correct?
- The mean error (bias) is +0.25 m.
- The RMSE is about 2.1 m.
- Because the bias is small, the DEM’s vertical accuracy is better than 0.5 m.
- If the check points lay mostly under forest, a radar DEM would be expected to show a positive bias.
(a) 1, 2 and 4 only (b) 1 and 3 only (c) 2 and 3 only (d) 1, 2, 3 and 4
Answer: (a) 1, 2 and 4 only
- 1 true: sum = +2.0; 2.0/8 = 0.25 m.
- 2 true: squares sum to 2.25 + 4 + 9 + 1 + 0.25 + 6.25 + 12.25 + 1 = 36; \( \sqrt{36/8} = 2.12 \) m.
- 3 false: accuracy is described by RMSE (about 2.1 m); positive and negative errors cancel in the mean.
- 4 true: C-band radar partly reflects from the canopy, so the DEM sits above the ground (a surface-model bias).
Practice Q6. Two basins along a mountain front are analysed from a DEM:
| Basin | Front length along foot (km) | Straight front length (km) | \( V_{fw} \) (m) | \( E_{ld} \) (m) | \( E_{rd} \) (m) | \( E_{sc} \) (m) | AF |
|---|---|---|---|---|---|---|---|
| P | 12 | 10 | 50 | 1,300 | 1,250 | 1,000 | 62 |
| Q | 30 | 10 | 600 | 1,150 | 1,100 | 1,000 | 49 |
Which statements are correct?
- \( S_{mf} \) is 1.2 for P and 3.0 for Q.
- \( V_f \) is about 0.18 for P and 4.8 for Q.
- P is more likely than Q to lie along an active fault.
- Q’s asymmetry factor indicates strong tilting.
(a) 1, 2 and 3 only (b) 1 and 4 only (c) 2, 3 and 4 only (d) 1, 2, 3 and 4
Answer: (a) 1, 2 and 3 only
- 1 true: 12/10 = 1.2; 30/10 = 3.0.
- 2 true: P: \( 2 \times 50/(300 + 250) = 100/550 = 0.18 \); Q: \( 2 \times 600/(150 + 100) = 1200/250 = 4.8 \).
- 3 true: P has a straight front and a narrow V-shaped valley (both low values); Q has an embayed front and a broad valley floor, typical of an inactive front.
- 4 false: AF = 49 is close to the neutral value of 50. P’s 62 suggests some tilting.
Practice Q7. Which statements about DEM-derived hydrology are correct?
- Lowering the flow-accumulation threshold increases the extracted drainage density.
- Sink filling is needed because pits stop flow from reaching the basin outlet.
- The topographic wetness index is highest on steep ridge crests.
- For a cell with specific catchment area 300 m and slope 5°, TWI is about 8.1.
(a) 1, 2 and 4 only (b) 1 and 3 only (c) 2 and 3 only (d) 1, 2, 3 and 4
Answer: (a) 1, 2 and 4 only
- 1 true: more cells qualify as channels.
- 2 true: an unfilled pit is a dead end for routing.
- 3 false: ridge crests have small contributing areas and often steep slopes; TWI is highest in flat, convergent hollows and valley floors.
- 4 true: \( \ln(300/\tan 5°) = \ln(300/0.0875) = \ln 3429 = 8.14 \).
Quick Revision Table
| Idea | Fact |
|---|---|
| Hypsometry | bimodal: land mean about 0.8 km, ocean mean about 3.7 km; 29% land |
| Shelf | to 100–200 m; about 0.1°; wide on passive margins |
| Slope, rise | slope a few degrees (about 2–5°), canyons; rise = sediment apron (passive margins) |
| Abyssal plain | 3–6 km; gradient below about 1:1,000; flattest surfaces on Earth |
| Ridges | fast: axial high (EPR); slow: rift valley (MAR, Carlsberg); ultraslow: SWIR, Gakkel |
| Depth–age | \( d = 2500 + 350\sqrt t \) m (t in Myr, up to about 70 Myr) |
| Trench | deepest about 11 km (Challenger Deep) |
| Guyot, atoll | wave-planed and subsided; fringing → barrier → atoll (Darwin) |
| Aseismic ridges | Ninetyeast (Kerguelen), Chagos–Laccadive (Réunion) |
| Canyons and fans | turbidity currents; Swatch of No Ground; Bengal Fan largest |
| Echo sounding | \( d = vt/2 \), \( v \approx 1500 \) m s\(^{-1}\); swath \( W = 2d\tan(\theta/2) \) |
| DEM types | DEM generic; DSM surface; DTM bare earth; raster vs TIN |
| Sources | SRTM (2000, InSAR, 1″ and 3″), ASTER GDEM, CartoDEM, AW3D30, TanDEM-X, LiDAR, SfM |
| Arc-second | 1″ ≈ 30.9 m N–S; × cos φ E–W |
| Slope | \( \tan\beta = \sqrt{(\partial z/\partial x)^2 + (\partial z/\partial y)^2} \); central differences over 2Δ |
| D8 | steepest drop ÷ distance; diagonal distance √2 Δ |
| Workflow | fill → direction → accumulation → threshold → order → watershed |
| TWI, SPI | \( \ln(a/\tan\beta) \); \( a\tan\beta \) |
| Morphometry | \( D_d \), \( R_b \) 3–5, \( R_e \), \( R_c \), \( R_f \), HI |
| Tectonic indices | \( S_{mf} \) and \( V_f \) low = active; AF far from 50 = tilt; SL and \( k_{sn} \) high = uplift or hard rock |
Key Takeaways
What’s Next
- Environmental Change and Extra-terrestrial Geomorphology: the last official topic line, including DEM-based studies of other planets.
- Revisit Stream Flow, Hydrographs and Flood Frequency for how basin shape and drainage density affect hydrographs.
- Geomorphology: Quick Revision.