Bright Spots, AVO, VSP, 3D Seismics and Seismic Stratigraphy
Direct hydrocarbon indicators, AVO intercept-gradient and classes, vertical seismic profiling, 3D survey design and seismic stratigraphy for CSIR NET.
- 21 min
On this page · 15 sections
- Prerequisites
- The Hook: When Amplitude Became a Drilling Tool
- Rock Physics Behind Amplitude
- Bright Spots and Other Direct Hydrocarbon Indicators
- AVO: Amplitude Versus Offset (Angle)
- Vertical Seismic Profiling (VSP)
- 3D Seismics
- Seismic Stratigraphy
- Memory Tricks
- Don’t Confuse
- Common Mistakes
- Practice
- Quick Revision Table
- Key Takeaways
- What’s Next
Prerequisites
- Snell’s Law, Ray Theory and the Zoeppritz Equations — impedance, reflection coefficients, the Shuey intercept–gradient form.
- Seismic Data Processing — amplitude-preserving processing, f-k separation, migration.
- Refraction and Reflection Interpretation — reading sections and velocity pitfalls.
- Stratigraphic Code, Correlation and Sequence Stratigraphy — sequences and systems tracts from the outcrop and well side.
- Porosity Logs: Sonic, Density, Neutron and Gamma Ray — the logs that calibrate amplitudes and tie wells to seismic.
The Hook: When Amplitude Became a Drilling Tool
How CSIR NET asks it. Part C (Geophysics) asks which feature is a direct hydrocarbon indicator and why, AVO class from intercept and gradient, Poisson’s ratio from \(V_P/V_S\), VSP wavefields and time-depth numbers, 3D bin-size and fold logic, and seismic-stratigraphic terms (onlap, downlap, toplap, truncation; seismic facies; systems tracts) applied to a described section.
Rock Physics Behind Amplitude
Replacing brine by gas in the pores of a porous sandstone:
| Property | Effect of gas | Why |
|---|---|---|
| \(V_P\) | Falls sharply, even at low gas saturation | Gas makes the pore fluid very compressible, lowering the bulk modulus of the saturated rock (Gassmann fluid substitution) |
| \(V_S\) | Slightly rises | Shear modulus is unaffected by fluid; density falls |
| \(\rho\) | Falls | Gas is far lighter than brine |
| \(V_P/V_S\), Poisson’s ratio \(\sigma\) | Fall | Because \(V_P\) drops while \(V_S\) does not |
| Impedance | Falls | Both \(V_P\) and \(\rho\) drop |
Poisson’s ratio from velocities:
$$\sigma = \frac{(V_P/V_S)^2 - 2}{2\left[(V_P/V_S)^2 - 1\right]}$$\(V_P/V_S = 2\) gives \(\sigma = 1/3\) (typical of brine-saturated sands and shales); \(V_P/V_S = 1.5\) gives \(\sigma = 0.10\) (typical of gas sands).
Bright Spots and Other Direct Hydrocarbon Indicators
| DHI | What causes it | How it looks | Pitfalls |
|---|---|---|---|
| Bright spot | Low-impedance gas sand below higher-impedance shale | Anomalously strong negative reflection at the top of the reservoir, often limited to the structural crest | Coals, low-impedance volcanic ash, tuning of thin beds, fizz gas |
| Dim spot | High-impedance reservoir (e.g. consolidated sand, carbonate) whose impedance gas reduces towards that of the cap rock | Locally weaker reflection over the crest | Easy to miss; lithology changes do the same |
| Polarity reversal | Gas lowers a slightly-higher-impedance sand to below the shale | Reflection changes sign where it crosses the gas–water contact laterally | Needs careful phase control |
| Flat spot | Fluid contact (gas–water, gas–oil, oil–water): impedance increases from gas- to water-filled sand | Flat (or nearly flat after depth conversion) positive reflection cutting across dipping strata | Flat lithological layers, multiples, other flat-lying interfaces that mimic a contact |
| Velocity push-down (sag) | Slow gas column above deeper reflectors | Underlying reflectors sag in time beneath the accumulation | Lateral velocity changes in the overburden |
| Frequency loss / low-frequency shadow | Absorption in gas | Lower dominant frequency beneath the reservoir | Processing artefacts |
| Gas chimney | Gas leaking upwards | Vertical zone of disturbed, low-amplitude reflections | Faults, processing noise |
| Amplitude conformance | The anomaly is limited by a fluid contact | Amplitude edge follows a structural contour | Stratigraphic pinch-outs can coincide |
Polarity display depends on the convention used, so always check how a known positive reflection (such as a hard sea floor) appears on the section before calling a bright spot “negative”.
Push-down example. A 50 m gas column with \(V_P = 2000\) m/s, replacing brine sand with \(V_P = 2500\) m/s, delays deeper reflections by
$$\Delta t = 2h\left(\frac{1}{V_{gas}} - \frac{1}{V_{brine}}\right) = 100\left(\frac{1}{2000} - \frac{1}{2500}\right) = 0.010\ \mathrm{s} = 10\ \mathrm{ms}$$AVO: Amplitude Versus Offset (Angle)
Basis
From the Zoeppritz equations, linearised by Aki and Richards and rearranged by Shuey (derived on the first page of this unit):
$$R(\theta) \approx A + B\sin^2\theta$$- Intercept \(A\): the normal-incidence reflection coefficient, controlled by impedance contrast.
- Gradient \(B\): the rate of change with \(\sin^2\theta\), strongly affected by the contrast in Poisson’s ratio. A drop in Poisson’s ratio downward (shale over gas sand) makes \(B\) more negative.
- Ostrander’s work on gas sands showed that a large Poisson’s-ratio contrast makes reflection amplitude change markedly with offset, which turned AVO into a fluid indicator.
Workflow
graph TD
A["Amplitude-preserved
pre-stack CMP gathers"] --> B["NMO, mute,
offset-to-angle conversion"]
B --> C["Fit R = A + B sin²θ
at each time sample"]
C --> D["Intercept and
gradient volumes"]
D --> E["Crossplot A vs B:
background trend"]
E --> F["Anomalies off-trend:
candidate hydrocarbons"]
F --> G["Calibrate with wells,
fluid substitution, models"]Requirements: amplitude-preserving processing (no AGC), correct spherical-divergence and absorption compensation, NMO stretch control, conversion from offset to angle with a velocity model, and awareness of tuning, anisotropy and noise at far offsets.
AVO classes (top of a gas sand under shale)
| Class | Gas-sand impedance vs shale | Intercept \(A\) | Gradient \(B\) | Amplitude behaviour with angle |
|---|---|---|---|---|
| I | Higher | Large positive | Negative | Positive reflection dims with angle; may reverse polarity at far offsets |
| II (IIp if polarity reverses) | Nearly equal | Small (positive or negative) | Negative | Weak near offsets, grows at far offsets; polarity reversal if \(A > 0\) |
| III | Lower | Negative | Negative | Strong negative at all offsets and brighter with angle: the classic bright spot |
| IV | Lower | Negative | Positive | Strong negative near offsets whose magnitude decreases with angle (e.g. when the overlying rock is hard and fast) |
Classes I to III follow Rutherford and Williams; class IV was added later by Castagna and co-workers.
Intercept–gradient crossplot
- Brine sands and shales fall along a background trend with negative slope through the origin.
- Gas sands plot away from it: tops of class III sands in the quadrant with \(A < 0\), \(B < 0\) (positive product \(A\times B\)); bases in the opposite quadrant.
- Common derived attributes: the product \(A\times B\) (high for class III), \(A + B\) (a pseudo-Poisson’s-ratio reflectivity), near and far angle stacks, and “fluid factor” type deviations from the background trend.
Vertical Seismic Profiling (VSP)
In a VSP, the source is at the surface and receivers (clamped multi-component geophones or hydrophones) are placed at many depths in a borehole. Because the receiver is inside the earth, it records both the downgoing and the upgoing wavefields.
Types
| Type | Geometry | Main use |
|---|---|---|
| Check-shot survey | Few, widely spaced levels; first breaks only | Time–depth curve, sonic-log calibration |
| Zero-offset VSP | Source near the wellhead | Time–depth, interval velocities, well-to-seismic tie, multiple identification, corridor stack |
| Offset VSP | Source at a fixed offset | Imaging a strip of the reflector away from the well, AVO calibration, converted waves |
| Walkaway VSP | Many source positions along a line | Angle-dependent amplitudes, anisotropy, 2D image around the well |
| Walk-above VSP | Source moved to stay above receivers in a deviated well | Vertical-incidence data along a deviated well |
| Reverse VSP | Source in the well (or drill bit), receivers at the surface | Imaging with many surface receivers; drill-bit seismic |
| 3D VSP | Areal grid of sources | Imaging around the well in 3D |
Wavefields on a zero-offset VSP
On a display of depth (vertical) against one-way recording time (horizontal):
- The first break (direct downgoing P) arrives later with increasing depth; its slope gives interval velocity: \(V_{int} = \Delta z/\Delta t_{fb}\).
- Downgoing multiples are parallel to the first break.
- Upgoing reflections arrive earlier at deeper receivers (the receiver is closer to the reflector), so they slope the opposite way, and each meets the first-break curve at the depth of its reflector.
- Tube waves, slow waves travelling in the borehole fluid, are a major noise, as are casing-ringing and converted waves.
Key relation. For an upgoing primary recorded at depth \(z\) at time \(t_{up}(z)\), with first-break time \(t_{fb}(z)\):
$$t_{up}(z) + t_{fb}(z) = T_{surface}$$where \(T_{surface}\) is the two-way time of that reflection on surface seismic. Adding the first-break time to each trace aligns upgoing events at their surface two-way times (flattening them); subtracting it aligns the downgoing waves.
Processing and uses
- Pick first breaks → time–depth curve and interval velocities.
- Separate downgoing and upgoing wavefields (median filtering after alignment, or f-k filtering; they dip in opposite directions).
- Deconvolve the upgoing field with the downgoing field: the downgoing wavefield is the actual source wavelet plus all downgoing multiples, so this deconvolution removes both.
- Flatten upgoing events to two-way time and make a corridor stack (summing a narrow window just after the first break, where multiples generated deeper have not yet arrived).
- Compare with surface seismic and synthetic seismograms.
Uses: precise well ties (which reflection is which horizon), checking whether an event is a primary or a multiple, Q estimation from the change of the direct wavelet with depth, looking ahead of the bit, imaging near salt flanks and steep dips, and calibrating anisotropy and AVO.
3D Seismics
Why 3D
A 2D line assumes all reflections come from the vertical plane below it. In real structures energy arrives from the side (sideswipe), 2D migration cannot put it back, and maps interpolated between lines miss small faults and channels. A 3D survey samples the subsurface on a dense areal grid and is migrated in 3D, so reflectors move to their true positions in both directions and the Fresnel zone shrinks in both horizontal directions.
Vocabulary
| Term | Meaning |
|---|---|
| Inline | Direction of receiver lines (land) or sail lines (marine) |
| Crossline | Perpendicular to inline |
| Bin | Small rectangular cell (for example 12.5 m × 25 m or 25 m × 25 m) collecting all traces whose midpoints fall in it |
| Fold per bin | Number of traces in a bin; total fold = inline fold × crossline fold |
| Offset and azimuth distribution | Range of offsets and source–receiver directions in each bin; uniformity matters for AVO and multiple attenuation |
| Patch / template | The set of live receivers for one shot |
| Migration aperture / halo | Extra survey area so that dipping events at the edge of the target can be migrated in |
For orthogonal land geometry the bin dimensions are half the receiver interval (inline) and half the source interval (crossline).
Geometries
- Land: orthogonal (source lines perpendicular to receiver lines, the most common), brick, slant and zigzag layouts.
- Marine: a vessel towing several streamers and one or more source arrays gives narrow-azimuth data; multi-vessel wide-azimuth and multi-azimuth surveys and ocean-bottom nodes give the full azimuth coverage needed below salt.
Bin size and spatial aliasing
For a reflector dip \(\theta\), interval velocity \(V\) and highest frequency to be imaged \(f_{max}\), unaliased sampling of the zero-offset time dip \(2\sin\theta/V\) requires
$$\boxed{\Delta x \le \frac{V}{4f_{max}\sin\theta}}$$Example: \(V = 3000\) m/s, \(f_{max} = 60\) Hz, \(\theta = 30°\): \(\Delta x \le 3000/(4\times60\times0.5) = 25\) m.
Interpreting 3D volumes
- Time slices: horizontal sections at constant time; dipping reflectors appear as bands whose width shows dip; faults show as offsets of the bands.
- Horizon slices: amplitude extracted along (or parallel to) an interpreted horizon; show channels, fans, reefs as map-view depositional shapes.
- Attributes: amplitude (DHIs), coherence/variance (faults and channel edges), curvature (fractures, flexures), spectral decomposition (tuning thickness variations), impedance from inversion.
- Geobodies and visualisation: opacity rendering of anomalies in 3D.
4D (time-lapse) and multi-component
- 4D seismic repeats a 3D survey over a producing field. Differences in amplitude and travel time show where fluids have moved, pressure has changed and where bypassed oil remains. Repeatability of source and receiver positions is the key requirement; permanent ocean-bottom arrays are used in some fields.
- Multi-component (4C/9C) surveys record converted PS waves, which image through gas clouds (S waves are little affected by gas) and give \(V_P/V_S\).
Seismic Stratigraphy
The founding principle
Primary seismic reflections are generated by physical surfaces with impedance contrasts: bedding surfaces and unconformities. These surfaces are essentially time lines (chronostratigraphic surfaces). A reflection therefore follows a time surface and may cross diachronous lithological (facies) boundaries. This makes seismic data a tool for stratigraphy and depositional history, not just structure. The approach was set out by Vail and co-workers at Exxon in AAPG Memoir 26 (1977).
Seismic stratigraphy proceeds in three steps:
- Seismic sequence analysis: pick sequence boundaries (unconformities and their correlative conformities) from reflection terminations.
- Seismic facies analysis: describe and interpret reflection character within each sequence.
- Relative sea-level analysis: reconstruct coastal onlap and relative sea-level change.
Reflection terminations
| Termination | Position | Geometry | Typical meaning |
|---|---|---|---|
| Onlap | At the base of a unit | Initially horizontal strata end against an inclined surface, landward | Progressive infilling, transgression, rising relative sea level |
| Downlap | At the base | Initially inclined strata end down-dip against a flatter surface | Progradation (clinoforms) over a surface of condensed deposition |
| Toplap | At the top | Inclined strata thin and end up-dip against an overlying surface, without erosion | Sediment bypass at base level; progradation with little accommodation |
| Erosional truncation | At the top | Strata cut by an erosional surface | Erosion; unconformity (sequence boundary) |
| Concordance | Top or base | Strata parallel to the boundary | No break evident |
Baselap = onlap + downlap (both at the base). Onlap and downlap can be hard to distinguish after later tilting.
Seismic facies
Parameters: reflection configuration, continuity, amplitude, frequency, interval velocity and the external form of the unit.
| Internal configuration | Interpretation |
|---|---|
| Parallel / subparallel | Uniform deposition on a stable or uniformly subsiding surface (shelf, basin plain) |
| Divergent | Wedge thickening down-dip: differential subsidence or tilting during deposition |
| Sigmoid clinoforms | Prograding slope with preserved topsets: low energy, high supply, rising relative sea level (aggradation) |
| Oblique clinoforms | Prograding slope with toplap, no topsets: high energy, little accommodation, sediment bypass |
| Complex sigmoid–oblique, shingled, hummocky | Mixed or variable conditions; shingled = thin prograding units in shallow water |
| Chaotic | Slumps, slides, channel fills, high energy or deformation |
| Reflection-free | Homogeneous bodies: massive sands or shales, salt, igneous intrusions, reef cores |
External forms: sheet, sheet drape, wedge, bank, lens, mound (reefs, fans, contourite drifts, volcanic piles) and fill (channel, trough, canyon, basin fills).
Sequence stratigraphy in one diagram
graph TD
SB["Sequence boundary
unconformity + correlative conformity
erosional truncation below, onlap above"] --> LST["Lowstand systems tract
basin-floor fans, slope fans,
prograding wedge"]
LST --> TS["Transgressive surface"]
TS --> TST["Transgressive systems tract
retrogradational, onlap landward"]
TST --> MFS["Maximum flooding surface
condensed section,
downlap surface"]
MFS --> HST["Highstand systems tract
aggradational then progradational,
downlap onto MFS"]
HST --> SB2["Next sequence boundary"]- A depositional sequence is a relatively conformable succession of genetically related strata bounded by unconformities or their correlative conformities.
- The maximum flooding surface (MFS) is the surface onto which highstand clinoforms downlap; it is often a condensed, organic-rich (source-rock) interval.
- Systems tracts link reflection geometry to the relative sea-level cycle: falling stage and lowstand (forced regression, fans), transgression (retrogradation), highstand (aggradation then progradation).
Memory Tricks
Don’t Confuse
| This | vs | That |
|---|---|---|
| Bright spot: anomalously strong reflection at top of a low-impedance gas sand | vs | Flat spot: flat reflection at a fluid contact, cutting across dip |
| Dim spot: gas reduces an originally strong (hard-sand) contrast | vs | Bright spot: gas increases an originally weak or negative contrast |
| AVO intercept \(A\): normal incidence, impedance | vs | AVO gradient \(B\): change with angle, Poisson’s-ratio contrast |
| Class III: \(A < 0\), \(B < 0\), brightens | vs | Class IV: \(A < 0\), \(B > 0\), fades |
| Check-shot: first breaks only | vs | VSP: full waveforms, up- and downgoing fields |
| Zero-offset VSP: 1D time-depth, tie | vs | Walkaway VSP: many offsets, AVO and anisotropy |
| Time slice: constant time, cuts across horizons | vs | Horizon slice: follows a horizon, shows depositional shapes |
| 3D: one survey | vs | 4D: repeated 3D surveys over time |
| Onlap: horizontal strata end against an inclined surface | vs | Downlap: inclined strata end down-dip on a flatter surface |
| Toplap: non-erosional, bypass | vs | Truncation: erosional |
| Sigmoid clinoforms: topsets preserved, rising sea level | vs | Oblique clinoforms: toplap, no topsets, little accommodation |
Common Mistakes
Practice
All questions below are original practice questions written in CSIR NET Part C (Geophysics) style. They are not previous-year questions.
Level 1: Foundation
- What fluid feature does a flat spot usually mark?
- On a zero-offset VSP, which wavefield arrives earlier at deeper receivers?
- What is downlap?
Answers
- A fluid contact (gas–water, gas–oil or oil–water).
- The upgoing (reflected) wavefield.
- Initially inclined strata terminating down-dip against an underlying flatter surface (a baselap termination, typical of prograding clinoforms).
Level 2: Part B Style
Q1 (practice). At the top of a sand, AVO analysis gives intercept \(A = -0.12\) and gradient \(B = -0.20\). The response is best described as:
- (a) Class I, dimming with offset
- (b) Class II with polarity reversal
- (c) Class III, brightening with offset
- (d) Class IV, fading with offset
Answer and explanation
(c). A clearly negative intercept (low-impedance sand) with a negative gradient: the reflection becomes more negative with angle. Class IV would need \(B > 0\); class I needs a large positive \(A\).
Q2 (practice). In a zero-offset VSP, first breaks arrive at 0.500 s at 1000 m and 0.580 s at 1200 m. At 1000 m an upgoing reflection arrives at 0.900 s. The interval velocity between 1000 and 1200 m, and the surface two-way time of that reflection, are:
- (a) 2500 m/s and 1.40 s
- (b) 2000 m/s and 1.40 s
- (c) 2500 m/s and 0.40 s
- (d) 1250 m/s and 1.80 s
Answer and explanation
(a). \(V_{int} = 200/0.080 = 2500\) m/s. \(T_{surface} = t_{up} + t_{fb} = 0.900 + 0.500 = 1.40\) s. Option (c) subtracts instead of adding. The reflector lies at the depth where the upgoing event meets the first-break curve, i.e. where the one-way time is 0.70 s.
Q3 (practice). A 3D survey must image dips up to 30° at frequencies up to 60 Hz where the velocity is 3000 m/s. The largest bin dimension that avoids spatial aliasing is:
- (a) 12.5 m
- (b) 25 m
- (c) 50 m
- (d) 100 m
Answer and explanation
(b). \(\Delta x \le V/(4f_{max}\sin\theta) = 3000/(4\times60\times0.5) = 25\) m. A 12.5 m bin also satisfies the condition but is not the largest; 50 m would alias the 60 Hz dipping energy.
Q4 (practice). In a transgressive–regressive succession, the surface onto which overlying highstand clinoforms downlap is most likely:
- (a) a sequence boundary
- (b) the transgressive surface
- (c) the maximum flooding surface
- (d) an erosional truncation surface
Answer and explanation
(c). The maximum flooding surface caps the transgressive systems tract and is the downlap surface for highstand progradation. Sequence boundaries show truncation below and onlap above.
Level 3: Part C Style
Q1 (practice). A sandstone reservoir has these properties:
| State | \(V_P\) (m/s) | \(V_S\) (m/s) | \(\rho\) (g/cm³) |
|---|---|---|---|
| Brine-filled | 2500 | 1250 | 2.20 |
| Gas-filled | 2000 | 1330 | 2.05 |
A 50 m gas column sits on top of the brine leg.
(i) Compute Poisson’s ratio in each state. (ii) Compute the normal-incidence reflection coefficient at the gas–water contact and state what feature it forms. (iii) Compute the time push-down of reflectors beneath the gas column.
Answer and worked solution
- Brine: \(V_P/V_S = 2.00\) → \(\sigma = (4 - 2)/(2\times3) = 0.333\). Gas: \(V_P/V_S = 1.504\), squared 2.261 → \(\sigma = 0.261/(2\times1.261) = 0.104\). A large fall in Poisson’s ratio: the AVO signature of gas.
- \(Z_{gas} = 2.0\times2.05 = 4.10\); \(Z_{brine} = 2.5\times2.20 = 5.50\) (units of \(10^6\) kg m⁻² s⁻¹). \(R = (5.50 - 4.10)/(5.50 + 4.10) = 1.40/9.60 = +0.146\). A positive, horizontal (in depth) reflection at the contact: a flat spot.
- \(\Delta t = 2(50)(1/2000 - 1/2500) = 100\times0.0001 = 0.010\) s = 10 ms of push-down.
Q2 (practice). At the top of a reservoir, amplitude-preserved angle stacks give \(R = -0.10\) at 10° and \(R = -0.16\) at 30°. Using \(R = A + B\sin^2\theta\), consider:
(A) \(A \approx -0.09\) and \(B \approx -0.27\). (B) The response is Class III. (C) The product \(A\times B\) is positive, as expected for the top of a class III gas sand. (D) The analysis would be unaffected if a 500 ms AGC had been applied to the gathers first.
Which are correct?
- (a) A, B and C only
- (b) A and D only
- (c) B, C and D only
- (d) A, B, C and D
Answer and worked solution
(a) A, B and C.
- \(\sin^2 10° = 0.0302\), \(\sin^2 30° = 0.25\). \(B = (-0.16 + 0.10)/(0.25 - 0.0302) = -0.06/0.2198 = -0.273\). \(A = -0.10 - B(0.0302) = -0.10 + 0.0082 = -0.092\). (A) correct.
- (B) Negative intercept, negative gradient, brightening: class III. Correct.
- (C) \((-0.092)(-0.273) = +0.025 > 0\). Correct.
- (D) Wrong: AGC rescales windows trace by trace and distorts the offset-dependent amplitudes AVO measures.
- Extrapolating, \(R(40°) \approx -0.092 - 0.273\times0.413 = -0.205\), though far-angle estimates should be checked against the full Zoeppritz response.
Q3 (practice). A migrated 2D section across a passive margin shows, from bottom to top:
- Unit 1: parallel reflections, cut at the top by a surface S1.
- Above S1, near the basin floor: a mounded unit whose reflections onlap S1 on both sides.
- Unit 3: reflections that step progressively landward and onlap S1 landward, capped by a surface S2.
- Unit 4: sigmoid clinoforms whose bottomsets downlap onto S2.
Which interpretation is consistent?
- (a) S1 is a sequence boundary, the mound is a lowstand basin-floor fan, unit 3 is a transgressive systems tract, S2 is a maximum flooding surface and unit 4 is a highstand systems tract.
- (b) S1 is a maximum flooding surface, the mound is a reef in the highstand, S2 is a sequence boundary.
- (c) S1 is a correlative conformity with no erosion, unit 3 is a lowstand prograding wedge, S2 is a transgressive surface.
- (d) All four units belong to one highstand systems tract.
Answer and worked solution
(a).
- Truncation of unit 1 at S1 with onlap above it marks an unconformity: a sequence boundary.
- A mounded body on the basin floor, onlapping the boundary, is the classic lowstand basin-floor fan.
- Landward-stepping (retrogradational) reflections with landward onlap are the transgressive systems tract.
- The surface on which the next clinoforms downlap is the maximum flooding surface; sigmoid clinoforms above it, with topsets, are the highstand systems tract.
- (b) and (c) invert the meaning of truncation and downlap; (d) ignores the bounding surfaces.
Quick Revision Table
| Item | Fact |
|---|---|
| Gas effect | \(V_P\) falls sharply; \(V_S\) slightly up; \(\rho\) down; \(\sigma\) down |
| Poisson’s ratio | \(V_P/V_S = 2\) → 1/3; 1.5 → 0.10 |
| Bright spot | Strong negative top of low-impedance gas sand; look-alikes: coal, fizz gas, tuning |
| Dim spot / flat spot | Weaker crest reflection over hard reservoir / flat positive reflection at fluid contact |
| Push-down | \(\Delta t = 2h(1/V_{gas} - 1/V_{brine})\) |
| AVO | \(R \approx A + B\sin^2\theta\); \(A\) impedance, \(B\) Poisson contrast |
| Classes | I (+A, dims), II (≈0 A, grows), III (−A, −B, brightens), IV (−A, +B, fades) |
| VSP wavefields | First break and downgoing slope one way; upgoing the other way |
| VSP relation | \(t_{up} + t_{fb} = T_{surface}\) |
| VSP uses | Time–depth, well tie, multiples, Q, look-ahead, corridor stack |
| 3D bin | Half receiver × half source interval; \(\Delta x \le V/(4f_{max}\sin\theta)\) |
| 3D interpretation | Time slices, horizon slices, coherence, curvature, spectral decomposition |
| 4D | Repeat 3D; fluid and pressure changes; repeatability |
| Seismic stratigraphy | Reflections follow time surfaces (Vail and co-workers, AAPG Memoir 26) |
| Terminations | Onlap, downlap (baselap); toplap, truncation (top) |
| Facies | Parallel, divergent, sigmoid, oblique, chaotic, reflection-free; mound, fill |
| Systems tracts | SB → LST → TS → TST → MFS (downlap surface) → HST |
Key Takeaways
What’s Next
- Quick Revision — every formula and term from the unit on one page.
- Seismic Data Processing — revisit migration and amplitude preservation, the foundation of all interpretation here.
- Seismic Methods: chapter overview — the official topic map for the unit.
- Well Logging — formation evaluation, which calibrates everything on this page.
- Earth Sciences — the other geophysics units of Part C.