Seismic Sources, Detectors and Noise
Seismic sources, Vibroseis correlation, air-gun bubbles, geophones, hydrophones, sampling, ghosts, coherent and random noise and arrays for CSIR NET.
- 17 min
On this page · 12 sections
Prerequisites
- Snell’s Law, Ray Theory and the Zoeppritz Equations — wave types, free-surface reflection (\(R \approx -1\)) and surface waves.
- Seismic Methods: chapter overview — how acquisition fits into the full workflow.
- Seismometry — the same damped-oscillator physics behind earthquake seismometers.
- Sampling Theorem, FFT, Z-Transform and Convolution — Nyquist and aliasing in general form.
- Damped harmonic oscillators and Fourier sampling at MSc level; decibel arithmetic is practised in Numerical Ability.
The Hook: The Fan That Hides the Oil
How CSIR NET asks it. Part C (Geophysics) questions here are short and specific: which source suits which setting, what Vibroseis correlation produces, why air guns are arrayed, what a geophone measures and how its response falls below the natural frequency, Nyquist and aliasing, ghost notches, CMP fold, array response and the \(\sqrt N\) rule for stacking random noise.
What a Good Source Must Do
| Requirement | Why it matters |
|---|---|
| Enough energy | Deep targets, long offsets, absorbing near-surface |
| Broad bandwidth | Resolution depends on bandwidth, not only on the dominant frequency |
| Short, known, repeatable wavelet | Deconvolution and time-lapse (4D) work need a stable signature |
| Little source-generated noise | Ground roll and air blast compete with reflections |
| Safe, permitted, affordable | Explosives in towns or protected seas are often not allowed |
Land sources
| Source | How it works | Strengths | Limits |
|---|---|---|---|
| Explosives (dynamite) | Charge fired in a shot hole, ideally below the weathered layer | Impulsive, broadband, high energy; good coupling below weathering | Drilling cost, permits, safety; not repeatable exactly |
| Vibroseis | Truck-mounted baseplate driven hydraulically with a controlled frequency sweep lasting several seconds | Controlled spectrum; usable in towns; several vibrators and sweeps can be summed | Needs correlation; harmonic distortion; poor on soft ground |
| Weight drop / accelerated weight drop | Heavy mass dropped or driven onto a plate | Cheap, repeatable, quick | Low energy; shallow targets |
| Sledgehammer, small shotgun-type sources | Hammer on a plate; small cartridge fired into the ground | Very cheap; engineering refraction | Very shallow only; stacking needed |
Vibroseis correlation. The vibrator puts a long, low-amplitude sweep \(s(t)\) (for example a linear upsweep over a few seconds through a band of tens of hertz) into the ground. Each reflection returns a delayed, scaled copy of the sweep, and the raw record is an unreadable overlap. Cross-correlating the record with the pilot sweep compresses every copy into a short wavelet:
$$\text{correlated trace} = s(t) \star \left[s(t) * r(t)\right] = \left[s(t)\star s(t)\right] * r(t)$$where \(\star\) is cross-correlation, \(*\) is convolution and \(r(t)\) the reflectivity. The effective wavelet is the autocorrelation of the sweep, the Klauder wavelet: zero-phase, with bandwidth equal to the sweep bandwidth. The usable correlated record is the raw record length minus the sweep length (the “listen time”).
Marine sources
| Source | Principle | Use |
|---|---|---|
| Air gun | High-pressure compressed air released suddenly into water | The standard marine source |
| GI (generator–injector) gun | A second air pulse injected into the expanding bubble to damp its oscillation | Cleaner, high-resolution signature |
| Water gun | A piston of water ejected; the cavity implodes | Little bubble pulse; precursor in the signature |
| Sparker | Electrical discharge between electrodes vaporises water | Shallow, high-resolution surveys |
| Boomer | Electromagnetically driven plate pushes water | Shallow, high-resolution |
| Chirp sub-bottom profiler | Swept-frequency transducer with correlation | Very high resolution of the upper sediments |
| Marine vibrator | Underwater vibrating plate with a sweep | Lower peak pressure alternative |
Explosives are now rarely used offshore because of their effect on marine life and their poor repeatability.
The air-gun bubble. After the initial pressure pulse, the air bubble overshoots, collapses and re-expands several times. Each oscillation radiates a weaker pulse: the bubble pulse, which looks like a train of multiples. Its period follows the Rayleigh–Willis relation,
$$T_b \propto \frac{(P\,V_g)^{1/3}}{P_h^{5/6}}$$where \(P\) is the firing pressure, \(V_g\) the chamber volume and \(P_h\) the absolute hydrostatic pressure at gun depth. Bigger guns give longer bubble periods; deeper guns give shorter ones. Remedies:
- Tuned arrays: guns of different volumes fired together. Their primary pulses add in phase, their bubbles have different periods and add incoherently. The array improves the primary-to-bubble ratio.
- Clusters: guns fired close together so their bubbles interact and damp.
- Signature deconvolution in processing, using a measured or modelled far-field signature.
Ghosts
A source or receiver below the sea surface sees a second, polarity-reversed copy of every wave reflected from the surface (\(R \approx -1\)): the ghost. For depth \(d\) and water velocity \(V_w\), the ghost lags by \(2d\cos\theta/V_w\) and the summed response has notches at
$$f_n = \frac{n\,V_w}{2d\cos\theta}, \qquad n = 0, 1, 2, \ldots$$At vertical incidence a streamer at 7.5 m has its first non-zero notch at \(1500/15 = 100\) Hz. Shallow towing preserves high frequencies but costs low frequencies (the notch at 0 Hz) and adds weather noise; deep towing does the reverse. Dual-sensor streamers and ocean-bottom recording combine pressure (hydrophone) and vertical velocity (geophone) data, whose ghosts have opposite polarity, to remove the receiver ghost. On land, a shot fired below the base of weathering produces a source ghost from that interface and from the surface.
Detectors
The moving-coil geophone
A coil suspended on springs moves relative to a permanent magnet fixed to the case. When the ground moves, the case (and magnet) moves with it, the inertial coil lags, and the relative motion induces a voltage proportional to the relative velocity (Faraday’s law). The system is a damped harmonic oscillator:
$$\ddot{y} + 2h\omega_0\dot{y} + \omega_0^2 y = -\ddot{u}$$with \(y\) the coil displacement relative to the case, \(u\) the ground displacement, \(\omega_0 = 2\pi f_0 = \sqrt{k/m}\) and \(h\) the damping ratio.
| Property | Behaviour |
|---|---|
| Output | Voltage proportional to ground velocity above \(f_0\) |
| Natural frequency \(f_0\) | Set by spring stiffness and coil mass; low-frequency geophones are used for refraction and deep reflection work |
| Below \(f_0\) | Response falls off as a second-order system: about 12 dB per octave |
| Damping | Usually set (by a shunt resistor) at a substantial fraction of critical, around 0.6–0.7, to give a flat response with little ringing near \(f_0\) |
| Components | Vertical (P-wave work), horizontal (S-wave work), three-component (3C) |
| Coupling | Spike firmly planted; poor planting causes resonance and noise |
Digital MEMS accelerometers record acceleration with a flat response down to very low frequency and are used in some modern land systems.
Hydrophones
A hydrophone uses a piezoelectric element that responds to pressure, and is omnidirectional. Pairs are wired so that their responses to acceleration (from cable jerks) cancel while their pressure responses add (acceleration-cancelling hydrophones).
- Streamers: long cables of hydrophone groups towed behind the vessel, kept at depth by depth controllers (“birds”), positioned by compasses and acoustic networks, with a tail buoy at the far end.
- Ocean-bottom cables (OBC), nodes (OBN) and seismometers (OBS): sensors on the sea floor. 4C recording (hydrophone + three geophones) records S waves converted at reflectors (PS imaging) and allows receiver deghosting.
Recording
- Pre-amplifier → anti-alias (high-cut) filter → A/D converter (modern systems are 24-bit) → storage, via cables, telemetry or autonomous cable-free nodes.
- Sampling interval \(\Delta t\) is typically 1, 2 or 4 ms. The Nyquist frequency is
so 2 ms gives 250 Hz and 4 ms gives 125 Hz. A frequency \(f\) above \(f_N\) is aliased to \(\lvert f - 2nf_N\rvert\), folding back into the signal band; it must be filtered out before digitising.
- Dynamic range in decibels: \(20\log_{10}(A_{max}/A_{min})\). Each bit adds about 6 dB, so an ideal 24-bit converter spans about 144 dB.
Spread geometry and fold
| Term | Meaning |
|---|---|
| Group interval \(\Delta g\) | Spacing of receiver groups (each a summed array) |
| Split spread | Source in the middle of the receiver line |
| End-on (off-end) spread | Source at one end; standard in marine work |
| Near/far offset | Shortest and longest source–receiver distances |
| Roll-along | Moving shot and active receivers along the line for continuous coverage |
| CMP fold | Number of traces sharing a common midpoint |
For a 2D line with \(N\) channels, group interval \(\Delta g\) and shot interval \(\Delta s\) (shots moving one way along the line):
$$\text{Fold} = \frac{N\,\Delta g}{2\,\Delta s}$$Example: 240 channels, 25 m groups, 50 m shots: fold \(= 240\times25/(2\times50) = 60\).
Noise
Signal is whatever the survey is designed to record: in a reflection survey, the primary reflections. Everything else is noise, including perfectly good seismic waves such as refractions and multiples.
Coherent noise
Coherent noise is predictable from trace to trace, so it can be attacked by its velocity, frequency or periodicity.
| Noise | Recognition on a shot record | Main remedies |
|---|---|---|
| Ground roll (Rayleigh waves) | Low velocity, low frequency, high amplitude, dispersive fan cone through the shot | Geophone arrays, low-cut filters, f-k filtering, muting, shot below weathering |
| Air wave (air blast) | Linear event at the speed of sound in air (about 330–340 m/s), high frequency | Buried shots, filtering, muting |
| Direct and refracted waves | Linear first arrivals | Muting (but used for statics) |
| Guided waves (shallow water, near-surface layer) | Dispersive, trapped energy | f-k filtering, muting |
| Multiples | Repeat primaries at later time; lower stacking velocity; periodic in shallow water | Predictive deconvolution, stacking, Radon/f-k, wave-equation methods |
| Side-scattered noise | Energy scattered from near-surface heterogeneities, often aliased | Arrays, dense sampling, f-k |
| Power-line noise | Monochromatic 50 Hz (India) or 60 Hz | Notch filter, avoid lines |
| Swell and cable noise (marine) | Very low frequency, strong on near-surface streamer sections | Low-cut filters, tow deeper, solid streamers |
| Seismic interference | Another vessel’s shots on your record | Time-sharing, editing, denoising |
Random (incoherent) noise
Wind, traffic, machinery, people walking, rain, microseisms and instrument noise vary randomly from trace to trace. Summing \(N\) traces with the same signal and independent random noise improves the signal-to-noise amplitude ratio by
$$\boxed{\sqrt{N}}$$because signal adds as \(N\) and random noise as \(\sqrt N\). Fold 36 gives a factor of 6, about 15.6 dB. This applies to vertical stacking (repeat shots or sweeps at one location) and horizontal (CMP) stacking. It does not apply to coherent noise, which stacks like signal unless its moveout differs.
Arrays: spatial filtering in the field
Geophones in a group are summed before recording. For \(n\) equal elements in a line with spacing \(\Delta x\), a wave of apparent wavelength \(\lambda_a\) along the array gives a normalised response
$$R(\lambda_a) = \left|\frac{\sin(n\pi\Delta x/\lambda_a)}{n\sin(\pi\Delta x/\lambda_a)}\right|$$- Vertically travelling reflections (very long \(\lambda_a\)) give \(R \approx 1\): passed.
- The first null is at \(\lambda_a = n\Delta x\), the array length.
- Response repeats with full pass at \(\lambda_a = \Delta x\) (spatial aliasing of the array).
- Design rule: make the array length at least the longest ground-roll wavelength to be suppressed, and the element spacing smaller than the shortest one.
A noise test (walkaway spread of single, closely spaced geophones) measures the velocities and wavelengths of the noise before arrays are designed.
graph LR
N["Noise problem"] --> C{"Coherent
or random?"}
C -- "Coherent" --> V{"Separable by
velocity?"}
V -- "Yes" --> A["Arrays, f-k filter,
muting, Radon"]
V -- "No, by periodicity" --> P["Predictive
deconvolution"]
C -- "Coherent, one frequency" --> F["Notch filter
for 50 Hz"]
C -- "Random" --> S["Vertical and CMP stacking
S/N up by root N"]Memory Tricks
Don’t Confuse
| This | vs | That |
|---|---|---|
| Vibroseis wavelet: Klauder, zero-phase after correlation | vs | Dynamite wavelet: impulsive, close to minimum-phase |
| Vertical stacking: same source–receiver position, repeated shots | vs | Horizontal (CMP) stacking: different offsets, same midpoint, after NMO |
| Ground roll: slow, low frequency, dispersive | vs | Air wave: about 330–340 m/s, high frequency, non-dispersive |
| Coherent noise: needs velocity/periodicity tools | vs | Random noise: falls as \(1/\sqrt N\) with stacking |
| Source ghost | vs | Receiver ghost; both from the free surface (or base of weathering on land) |
| Bubble pulse: source effect, fixed period | vs | Water-bottom multiple: path effect, period set by water depth |
| Temporal aliasing: \(\Delta t\) too large, \(f > 1/(2\Delta t)\) | vs | Spatial aliasing: trace spacing too large for the apparent wavelength |
Common Mistakes
Practice
All questions below are original practice questions written in CSIR NET Part C (Geophysics) style. They are not previous-year questions.
Level 1: Foundation
- What is the Nyquist frequency for a 2 ms sampling interval?
- Which physical quantity does a hydrophone respond to?
- What is the phase character of the correlated Vibroseis wavelet?
Answers
- \(f_N = 1/(2\times0.002) =\) 250 Hz.
- Pressure (via a piezoelectric element).
- Zero-phase (the Klauder wavelet, the autocorrelation of the sweep).
Level 2: Part B Style
Q1 (practice). A streamer is towed at 7.5 m depth in water of velocity 1500 m/s. For vertically arriving waves, the first non-zero receiver-ghost notch is at:
- (a) 50 Hz
- (b) 100 Hz
- (c) 200 Hz
- (d) 125 Hz
Answer and explanation
(b). \(f_1 = V_w/(2d) = 1500/15 = 100\) Hz. The ghost delay is \(2d/V_w = 10\) ms, and a delayed, inverted copy cancels the direct arrival at frequencies whose period divides the delay: 100, 200, 300 Hz, … and 0 Hz.
Q2 (practice). Data are sampled at 4 ms without an adequate anti-alias filter. A 150 Hz noise component will appear on the digital record at:
- (a) 150 Hz
- (b) 125 Hz
- (c) 100 Hz
- (d) 25 Hz
Answer and explanation
(c). \(f_N = 125\) Hz. A frequency 25 Hz above Nyquist folds back to 25 Hz below it: \(2(125) - 150 = 100\) Hz.
Q3 (practice). A 2D line uses 240 channels at 25 m group interval with a shot every 50 m (end-on spread). The CMP fold is:
- (a) 30
- (b) 120
- (c) 60
- (d) 240
Answer and explanation
(c). Fold \(= N\Delta g/(2\Delta s) = 240\times25/(2\times50) = 60\). CMP spacing is \(\Delta g/2 = 12.5\) m.
Q4 (practice). Which statement about air-gun arrays is correct?
- (a) Guns of identical volume are used so that bubbles add in phase.
- (b) Guns of different volumes are combined so that primary pulses add and bubble pulses partly cancel.
- (c) Arrays are used mainly to lower the dominant frequency.
- (d) An array removes the source ghost completely.
Answer and explanation
(b). Tuned arrays raise the primary-to-bubble ratio: the primaries are synchronous, the bubbles have different periods and add incoherently. The ghost is a free-surface effect that arrays do not remove.
Level 3: Part C Style
Q1 (practice). A noise test shows ground roll travelling at 400 m/s with frequencies of 8–20 Hz. Reflections arrive with apparent velocity 4000 m/s and dominant frequency 30 Hz. A linear array of 12 geophones at 4 m spacing is proposed.
(i) What range of ground-roll wavelengths must be suppressed? (ii) Compute the array response for the 8 Hz and 20 Hz ground roll and for the reflection. (iii) Express each in dB and comment on the design.
Answer and worked solution
- \(\lambda = V/f\): 400/8 = 50 m to 400/20 = 20 m. The array length \(n\Delta x = 48\) m is close to the longest wavelength, and \(\Delta x = 4\) m is well below the shortest.
- \(R = \sin(n\pi\Delta x/\lambda)/[n\sin(\pi\Delta x/\lambda)]\), \(n = 12\), \(\Delta x = 4\) m.
- 8 Hz, \(\lambda = 50\) m: \(\Delta x/\lambda = 0.08\); \(\sin(172.8°) = 0.1253\); \(12\sin(14.4°) = 2.984\); \(R = 0.042\).
- 20 Hz, \(\lambda = 20\) m: \(\Delta x/\lambda = 0.2\); \(\sin(432°) = \sin72° = 0.951\); \(12\sin36° = 7.053\); \(R = 0.135\).
- Reflection, \(\lambda = 4000/30 = 133.3\) m: \(\Delta x/\lambda = 0.03\); \(\sin(64.8°) = 0.905\); \(12\sin(5.4°) = 1.129\); \(R = 0.801\).
- \(20\log_{10}R\): ground roll −27.5 dB (8 Hz) and −17.4 dB (20 Hz); reflection −1.9 dB. The array suppresses ground roll strongly while passing reflections with little loss. The weaker rejection at 20 Hz comes from a sidelobe of the response; a slightly longer or weighted (tapered) array would flatten the reject band.
Q2 (practice). A land crew records 4 Vibroseis sweeps per vibrator point (vertically stacked) and processes the line at CMP fold 30. Consider:
(A) For random noise, the combined S/N amplitude improvement is about 11, roughly 21 dB. (B) The same factor applies to ground roll. (C) A 24-bit recorder has an ideal dynamic range of about 144 dB. (D) The vertical stack improves S/N even if the noise is perfectly repeatable from sweep to sweep.
Which are correct?
- (a) A and C only
- (b) A, B and C only
- (c) C and D only
- (d) A, C and D only
Answer and worked solution
(a) A and C only.
- (A) \(N = 4\times30 = 120\); \(\sqrt{120} = 10.95\); \(20\log_{10}10.95 = 20.8\) dB. Correct.
- (B) Wrong: ground roll is coherent and source-generated; it repeats with every sweep and stacks with the signal unless its moveout differs.
- (C) \(20\log_{10}2^{24} = 24\times6.02 = 144.5\) dB. Correct.
- (D) Wrong: repeatable noise adds coherently, exactly like signal, so vertical stacking cannot improve the ratio.
Q3 (practice). An air gun at a given depth has a bubble period of 120 ms. Using the Rayleigh–Willis scaling, estimate the period (i) if the chamber volume is increased 8 times at the same pressure and depth, and (ii) if instead the gun is lowered so that the absolute hydrostatic pressure doubles. (iii) Why does a tuned array use guns of several sizes?
Answer and worked solution
\(T_b \propto (PV_g)^{1/3}P_h^{-5/6}\).
- Volume × 8: period × \(8^{1/3} = 2\) → 240 ms.
- \(P_h\) × 2: period × \(2^{-5/6} = 0.561\) → about 67 ms.
- Different volumes give different bubble periods. Fired together, the first pressure peaks align and add, but the bubble oscillations fall out of step and partly cancel, giving a short, high primary-to-bubble signature that deconvolves well.
Quick Revision Table
| Item | Fact |
|---|---|
| Land sources | Dynamite (impulsive), Vibroseis (sweep), weight drop, hammer |
| Vibroseis | Correlate with pilot → Klauder wavelet, zero-phase, sweep bandwidth |
| Marine sources | Air gun (standard), GI gun, water gun, sparker, boomer, chirp |
| Bubble period | \(\propto (PV_g)^{1/3}/P_h^{5/6}\); tuned arrays raise primary-to-bubble ratio |
| Ghost notch | \(f_n = nV_w/(2d\cos\theta)\) |
| Geophone | Moving coil; velocity output above \(f_0\); −12 dB/octave below |
| Hydrophone | Piezoelectric, pressure, omnidirectional; acceleration-cancelling pairs |
| 4C / dual sensor | P + Z combine to remove the receiver ghost; PS imaging |
| Nyquist | \(f_N = 1/(2\Delta t)\); 2 ms → 250 Hz; 4 ms → 125 Hz |
| Alias | \(f\) appears at \(\lvert f - 2nf_N\rvert\) |
| Bits | About 6 dB per bit; 24-bit about 144 dB |
| 2D fold | \(N\Delta g/(2\Delta s)\) |
| Random noise | S/N up by \(\sqrt N\) on stacking |
| Array | First null at \(\lambda_a = n\Delta x\); length ≥ longest noise wavelength |
| Coherent noise | Ground roll, air wave, refractions, guided waves, multiples, 50 Hz |
Key Takeaways
What’s Next
- Refraction and Reflection Interpretation — turning recorded arrival times into depths and velocities.
- Seismic Data Processing — deconvolution, f-k filtering and stacking finish the noise fight begun in the field.
- Snell’s Law, Ray Theory and the Zoeppritz Equations — revisit free-surface reflection and surface waves.
- Quick Revision — the whole unit on one page.