Stress, Mohr Circle, Failure Criteria and Fault Reactivation
CSIR NET Geology Part C: stress tensor, 2D and 3D Mohr circles, Coulomb and Griffith criteria, effective stress, fracture modes, reactivation and slip tendency.
- 23 min
On this page · 16 sections
- Prerequisites
- The Hook: Faults That Should Not Move
- The Stress Tensor in Brief
- The Mohr Circle in Two and Three Dimensions
- Failure Criteria
- Pore Pressure and Effective Stress
- Fracturing in Nature
- Fault Reactivation
- Measuring and Inferring Stress
- Memory Tricks
- Don’t Confuse
- Common Mistakes
- Practice
- Quick Revision Table
- Key Takeaways
- What’s Next
Prerequisites
- The Part B treatment of stress, the Mohr circle and Anderson’s theory in Stress, Strain, Folds, Joints and Faults. This page assumes it and goes further.
- Principal stresses are eigenvalues of a symmetric tensor: see Linear Algebra, Matrices and Eigenvalues.
- Elastic moduli (Young’s modulus, Poisson’s ratio) from Seismology Basics and Earth’s Internal Structure.
The Hook: Faults That Should Not Move
The Stress Tensor in Brief
At a point, the stress state is a symmetric second-rank tensor with six independent components. Its eigenvalues are the principal stresses \( \sigma_1 \geq \sigma_2 \geq \sigma_3 \), with compression positive in geology. Three combinations matter most:
| Quantity | Definition | Physical role |
|---|---|---|
| Mean stress \( \sigma_m \) | \( (\sigma_1 + \sigma_2 + \sigma_3)/3 \) | volume change; pressure in phase diagrams |
| Deviatoric stress \( \sigma'_{ij} \) | \( \sigma_{ij} - \sigma_m\delta_{ij} \) | shape change; drives flow |
| Differential stress | \( \sigma_1 - \sigma_3 \) | controls fracture and the size of the Mohr circle |
| Stress ratio \( \Phi \) | \( (\sigma_2 - \sigma_3)/(\sigma_1 - \sigma_3) \), between 0 and 1 | shape of the stress ellipsoid; output of fault-slip inversion |
Lithostatic and tectonic stress
In a column of rock at rest, the vertical stress is the weight of the overburden:
$$\boxed{\sigma_v = \int_0^z \rho g\,dz \approx \rho g z}$$which is about 26.5 MPa km\(^{-1}\) for \( \rho = 2{,}700 \) kg m\(^{-3}\). A purely lithostatic state (\( \sigma_1 = \sigma_2 = \sigma_3 \)) has no differential stress and causes no faulting. Tectonic stress is the departure from it. If the rock is confined laterally and behaves elastically, the horizontal stress from the weight alone is
$$\sigma_h = \frac{\nu}{1-\nu}\sigma_v$$which is \( \sigma_v/3 \) for Poisson’s ratio \( \nu = 0.25 \). Thermal stresses, plate-boundary forces, topography and flexure add to this.
The Mohr Circle in Two and Three Dimensions
Two dimensions
For a plane whose normal makes angle \( \theta \) with \( \sigma_1 \) (so the plane itself makes \( 90° - \theta \) with \( \sigma_1 \)):
$$\boxed{\sigma_n = \frac{\sigma_1 + \sigma_3}{2} + \frac{\sigma_1 - \sigma_3}{2}\cos 2\theta \qquad \tau = \frac{\sigma_1 - \sigma_3}{2}\sin 2\theta}$$The circle has centre \( (\sigma_1 + \sigma_3)/2 \) and radius \( (\sigma_1 - \sigma_3)/2 \). An angle \( \theta \) in the rock becomes \( 2\theta \) on the circle.
Three dimensions
In 3D there are three circles, with diameters \( \sigma_1 - \sigma_3 \), \( \sigma_1 - \sigma_2 \) and \( \sigma_2 - \sigma_3 \). Every possible plane plots on or inside the large circle and outside the two small ones. Two consequences:
- The maximum shear stress anywhere is \( (\sigma_1 - \sigma_3)/2 \), on planes that contain \( \sigma_2 \) and bisect \( \sigma_1 \) and \( \sigma_3 \). So \( \sigma_2 \) does not control failure in the simple Coulomb model, and shear fractures form parallel to \( \sigma_2 \).
- A plane oblique to all three axes has lower shear stress than a plane containing \( \sigma_2 \) at the same normal stress. This is why Anderson faults contain \( \sigma_2 \).
The pole method
To read stresses straight off the circle, plot the two principal points, draw a line from the \( \sigma_1 \) point parallel to the \( \sigma_1 \) plane (the plane on which \( \sigma_1 \) acts) to find the pole, and then draw a line from the pole parallel to any plane: where it cuts the circle gives the stresses on that plane. It is the graphical version of the equations above and is handy for checking signs of shear stress.
Failure Criteria
Griffith theory and fracture mechanics
Real rocks contain microcracks. A. A. Griffith (1921) showed that a crack grows when the elastic energy released by its growth exceeds the surface energy of the new crack faces. For an elliptical crack of half-length \( a \) under remote tension \( \sigma \):
$$\boxed{\sigma_c = \sqrt{\frac{2E\gamma}{\pi a}}}$$where \( E \) is Young’s modulus and \( \gamma \) the specific surface energy. Longer cracks fail at lower stress, which is why rock tensile strength is a few MPa to tens of MPa, far below theoretical bond strength.
In fracture mechanics this is written with the stress intensity factor at the tip, \( K_I = Y\sigma\sqrt{\pi a} \) (\( Y \) is a geometry factor near 1). The crack propagates when \( K_I \) reaches the fracture toughness \( K_{IC} \).
The three fracture modes are:
| Mode | Displacement of crack walls | Geological example |
|---|---|---|
| I (opening) | perpendicular to the crack | joints, veins, dykes |
| II (sliding) | in the plane, perpendicular to the tip line | shear fractures, fault tips in profile |
| III (tearing) | in the plane, parallel to the tip line | lateral tips of faults |
Extended to compressive stress, Griffith’s theory gives a parabolic Mohr envelope:
$$\boxed{\tau^2 = 4T(\sigma_n + T)}$$It cuts the \( \sigma_n \) axis at \( -T \) and predicts uniaxial compressive strength of \( 8T \) in two dimensions. Measured ratios are often larger (10–20), because friction closes cracks under compression. That is why the Coulomb criterion is used at positive normal stress.
The Coulomb criterion
$$\boxed{\tau = C + \mu\sigma_n = C + \sigma_n\tan\phi}$$\( C \) is the cohesion and \( \mu = \tan\phi \) the coefficient of internal friction (\( \phi \) is the angle of internal friction). The circle touches this line on a plane whose normal is at \( 2\theta = 90° + \phi \) from \( \sigma_1 \), so the fracture plane makes
$$\boxed{\alpha = 45° - \frac{\phi}{2}}$$with \( \sigma_1 \). In principal stresses, failure occurs when
$$\boxed{\sigma_1 = \sigma_3\tan^2\left(45° + \frac{\phi}{2}\right) + 2C\tan\left(45° + \frac{\phi}{2}\right)}$$Setting \( \sigma_3 = 0 \) gives the uniaxial compressive strength \( 2C\tan(45° + \phi/2) \).
The composite Griffith–Coulomb envelope
Joining the Griffith parabola (tensile side) to a Coulomb line (compressive side), commonly with \( C \approx 2T \), gives one envelope for all fracture types. Where the circle touches decides the fracture mode:
| Differential stress | Point of contact | Fracture type | Orientation |
|---|---|---|---|
| \( \sigma_1 - \sigma_3 < 4T \) | vertex \( (-T, 0) \) | extension (mode I) | parallel to \( \sigma_1 \), normal to \( \sigma_3 \) |
| \( 4T < \sigma_1 - \sigma_3 < 4\sqrt{2}\,T \approx 5.66T \) | parabola, \( \sigma_n < 0 \) | hybrid extension–shear | small angle to \( \sigma_1 \), opening and slip |
| \( \sigma_1 - \sigma_3 > 5.66T \) | \( \sigma_n > 0 \) | shear | about 25–30° to \( \sigma_1 \) |
So pure extension fractures need both a small differential stress and an effective \( \sigma_3 \) that reaches \( -T \). At depth, all stresses are compressive; only a high pore pressure can make the effective \( \sigma_3 \) tensile.
Byerlee’s law: friction on existing faults
J. D. Byerlee (1978) compiled laboratory friction data on many rock types and found them almost independent of lithology:
$$\boxed{\tau = 0.85\,\sigma_n \quad (\sigma_n < 200\ \text{MPa}); \qquad \tau = 50\ \text{MPa} + 0.6\,\sigma_n \quad (200 < \sigma_n < 1{,}700\ \text{MPa})}$$Clay-rich gouges (especially smectite) and talc are the main exceptions; they are much weaker. A fault has no cohesion, so it slips at lower stress than intact rock of the same orientation.
Pore Pressure and Effective Stress
Pore fluid at pressure \( P_f \) supports part of the load. The rock behaves according to the effective stresses
$$\boxed{\sigma'_i = \sigma_i - P_f \qquad \tau' = \tau}$$Raising \( P_f \) moves the Mohr circle left by \( P_f \) with no change in its diameter. The pore-fluid factor compares fluid pressure with the vertical load:
$$\boxed{\lambda_v = \frac{P_f}{\sigma_v}}$$Hydrostatic pressure gives \( \lambda_v \approx 0.4 \) (water density over rock density); \( \lambda_v \to 1 \) means near-lithostatic overpressure. M. K. Hubbert and W. W. Rubey (1959) used high \( \lambda_v \) to explain how large, thin thrust sheets could move without being crushed.
Fracturing in Nature
Joints and veins
Joints are mode I fractures with no visible shear offset. They form perpendicular to \( \sigma_3 \) at low differential stress, often during uplift and cooling or under high pore pressure.
- Systematic joints are planar, parallel and regularly spaced; non-systematic joints are curved and end against others.
- Cross joints end at T-junctions against earlier joints, so the abutting joint is the younger.
- Joint spacing scales roughly with the thickness of the jointed bed: thin beds have closely spaced joints.
- Fractography: plumose structure (hackle plumes) radiates from the origin, rib or arrest marks record pauses, and twist hackle forms where the fracture front breaks into en echelon segments. The plume axis points the propagation direction.
Veins are fractures filled with minerals precipitated from fluid. Crack–seal veins record many cycles of opening and sealing, each needing \( P_f > \sigma_3 + T \). En echelon tension gashes in a shear zone open perpendicular to the local extension direction and rotate as shear continues, becoming sigmoidal.
Shear fractures and faults
Shear fractures form in conjugate sets at about 30° to \( \sigma_1 \). In nature, faults grow by linking many small fractures. A damage zone of fractures surrounds a fault core of gouge or cataclasite. Fault displacement \( D \) and length \( L \) scale roughly as \( D \propto L^{n} \), with \( n \) between about 1 and 1.5 in published compilations.
Hydraulic fracturing
When \( P_f \) exceeds \( \sigma_3 + T \), a fluid-filled crack opens perpendicular to \( \sigma_3 \). Magma does this as a dyke; industry does it in a borehole. In a hydraulic fracturing stress test, the pressure at which a fracture stays just open (the shut-in pressure) gives \( \sigma_{h\min} \), the least horizontal stress, directly.
Fault Reactivation
Sibson’s reactivation analysis
Most crust already contains faults. The question is whether an existing plane slips before a new, optimally oriented fracture forms. R. H. Sibson (1985) worked this out for a cohesionless plane containing \( \sigma_2 \) at angle \( \theta_r \) to \( \sigma_1 \), with sliding friction \( \mu_s \). Reactivation requires an effective stress ratio of
$$\boxed{R = \frac{\sigma'_1}{\sigma'_3} = \frac{1 + \mu_s\cot\theta_r}{1 - \mu_s\tan\theta_r}}$$- \( R \) is smallest (easiest slip) at the optimal angle \( \theta_r^* = \frac{1}{2}\tan^{-1}(1/\mu_s) \); for \( \mu_s = 0.6 \), \( \theta_r^* \approx 29.5° \) and \( R^* = (\sqrt{1+\mu_s^2} + \mu_s)^2 \approx 3.12 \).
- \( R \) rises steeply on either side. At \( \theta_r = 2\theta_r^* \) (about 59° for \( \mu_s = 0.6 \)) it becomes infinite: the fault is frictionally locked.
- For \( \theta_r > 2\theta_r^* \), \( R \) is negative. Reactivation is possible only if \( \sigma'_3 \) is tensile, that is, only with fluid overpressure.
| \( \theta_r \) (μ\(_s\) = 0.6) | 10° | 20° | 29.5° | 40° | 50° | 55° | 59° |
|---|---|---|---|---|---|---|---|
| \( R \) needed | 4.9 | 3.4 | 3.1 | 3.5 | 5.3 | 9.9 | about 950 |
Slip tendency and dilation tendency
For a quick map-scale screen, two ratios are used:
$$\boxed{T_s = \frac{\tau}{\sigma'_n}} \qquad \boxed{T_d = \frac{\sigma_1 - \sigma_n}{\sigma_1 - \sigma_3}}$$A fault slips if \( T_s \) reaches its sliding friction (about 0.6). Dilation tendency is highest for planes normal to \( \sigma_3 \) (\( T_d = 1 \)); these open most easily and carry fluid. Both are used to judge which faults of a given set are likely to leak or to be seismic.
The fault-valve model
Sibson also described fault-valve behaviour on steep reverse faults. These faults are badly oriented and need near-lithostatic fluid pressure to slip. Fluid pressure builds below a sealed fault; when it reaches failure, the fault ruptures, fluid surges up, pressure drops, minerals precipitate (often gold-bearing quartz veins) and the fault seals again. The result is repeated cycles of crack–seal veining on the fault.
Other reactivation settings
- Inversion: normal faults reactivated as reverse faults (positive inversion), or the reverse (negative inversion). Rift-margin faults reactivated in a later collision are typical examples (see Extensional, Compressional and Strike-Slip Terrains; Mantle Plumes).
- Induced seismicity: reservoir loading, fluid injection or extraction raise or lower \( P_f \) and shift the Mohr circle.
- Basement control: old shear zones and foliations, weaker than the surrounding rock, are reactivated in younger stress fields.
Measuring and Inferring Stress
| Method | What it gives | Key rule |
|---|---|---|
| Borehole breakouts | orientation of \( \sigma_{h\min} \) | breakouts (spalled zones) form on the borehole wall in the direction of \( \sigma_{h\min} \) |
| Drilling-induced tensile fractures | orientation of \( \sigma_{H\max} \) | they form parallel to \( \sigma_{H\max} \), at 90° to breakouts |
| Hydraulic fracturing test | magnitude of \( \sigma_{h\min} \) | shut-in pressure |
| Earthquake focal mechanisms | P and T axes, approximate \( \sigma_1 \), \( \sigma_3 \) | P and T lie at 45° to the nodal planes |
| Fault-slip inversion | principal directions and \( \Phi \) | Wallace–Bott assumption: slip is parallel to the maximum resolved shear stress |
| Overcoring | full tensor at shallow depth | strain relief on cutting a core |
| Calcite twins, recrystallised grain size | palaeo-differential stress | palaeopiezometers |
The World Stress Map project compiles these data. A first-order result is that stress orientation in plate interiors is consistent over large regions and often follows plate-boundary forces.
Memory Tricks
Don’t Confuse
| This | With this | Difference |
|---|---|---|
| Angle of plane to \( \sigma_1 \) | Angle of normal to \( \sigma_1 \) | they add to 90°; Mohr formulas use the normal |
| Coulomb criterion | Byerlee’s law | intact rock with cohesion versus sliding on existing, cohesionless faults |
| Internal friction \( \phi \) | Sliding friction \( \mu_s \) | property of intact rock versus of a surface; similar values, different meaning |
| Differential stress | Deviatoric stress | \( \sigma_1 - \sigma_3 \) (a scalar) versus the tensor minus mean stress |
| Extension fracture | Shear fracture | opens normal to \( \sigma_3 \), contains \( \sigma_1 \) versus about 30° to \( \sigma_1 \) with slip |
| Slip tendency | Dilation tendency | \( \tau/\sigma'_n \) for sliding versus normalised \( (\sigma_1 - \sigma_n) \) for opening |
| Borehole breakout | Drilling-induced tensile fracture | along \( \sigma_{h\min} \) versus along \( \sigma_{H\max} \) |
Common Mistakes
Practice
All questions below are original practice questions written for these notes.
Level 1: Foundation
- Practice. With a coefficient of internal friction of 0.6, at what angle to \( \sigma_1 \) does a Coulomb shear fracture form?
- Practice. Which friction law, nearly independent of rock type, describes sliding on pre-existing faults?
- Practice. A borehole shows breakouts on its north and south walls. What is the direction of \( \sigma_{H\max} \)?
Answers
- \( \phi = \tan^{-1}0.6 \approx 31° \), so the angle is \( 45° - 15.5° \approx 29.5° \), about 30°.
- Byerlee’s law: \( \tau = 0.85\sigma_n \) below 200 MPa normal stress, \( \tau = 50 + 0.6\sigma_n \) MPa above.
- Breakouts lie along \( \sigma_{h\min} \), so \( \sigma_{h\min} \) is N–S and \( \sigma_{H\max} \) is E–W.
Level 2: Part B Style
Practice Q4. \( \sigma_1 = 120 \) MPa, \( \sigma_3 = 40 \) MPa. The normal and shear stresses on a plane making 30° with \( \sigma_1 \) are:
(a) 100 MPa, 34.6 MPa (b) 60 MPa, 34.6 MPa (c) 60 MPa, 20 MPa (d) 80 MPa, 40 MPa
Answer: (b) 60 MPa, 34.6 MPa
The normal is at 60°, so \( 2\theta = 120° \). \( \sigma_n = 80 + 40\cos 120° = 60 \) MPa; \( \tau = 40\sin 120° = 34.6 \) MPa. Option (a) uses the plane angle; (d) is the maximum-shear plane.
Practice Q5. At 4 km depth in sediments of mean density 2,500 kg m\(^{-3}\) with hydrostatic pore pressure (\( g = 9.81 \) m s\(^{-2}\)), the pore-fluid factor \( \lambda_v \) is:
(a) 0.25 (b) 0.40 (c) 0.60 (d) 1.00
Answer: (b) 0.40
\( \sigma_v = 2500\times 9.81\times 4000 = 98.1 \) MPa; \( P_f = 1000\times 9.81\times 4000 = 39.2 \) MPa; \( \lambda_v = 39.2/98.1 = 0.40 \). It is simply the density ratio, 1,000/2,500.
Practice Q6. In the composite Griffith–Coulomb criterion with tensile strength \( T = 5 \) MPa, a hybrid extension–shear fracture forms when the differential stress at failure is:
(a) less than 20 MPa (b) between 20 and about 28 MPa (c) between 28 and 40 MPa (d) above 40 MPa
Answer: (b)
Hybrid fractures form for \( 4T < \Delta\sigma < 4\sqrt{2}T \), that is 20 to 28.3 MPa. Below 20 MPa the fracture is pure extension; above 28.3 MPa it is a shear fracture.
Practice Q7. A cohesionless fault with \( \mu_s = 0.6 \) contains \( \sigma_2 \). Which orientation is frictionally locked, so that it cannot slip unless \( \sigma'_3 \) is tensile?
(a) 15° to \( \sigma_1 \) (b) 30° to \( \sigma_1 \) (c) 45° to \( \sigma_1 \) (d) 65° to \( \sigma_1 \)
Answer: (d) 65°
Lock-up is at \( 2\theta_r^* = \tan^{-1}(1/0.6) \approx 59° \). Beyond that, \( 1 - \mu_s\tan\theta_r < 0 \), so the required \( R \) is negative and slip needs \( \sigma'_3 < 0 \).
Level 3: Part C Style
Practice Q8. Intact granite (\( C = 10 \) MPa, \( \mu = 0.6 \)) contains an old cohesionless fault (\( \mu_s = 0.6 \)) at 50° to \( \sigma_1 \), containing \( \sigma_2 \). The effective least stress is held at \( \sigma'_3 = 20 \) MPa while \( \sigma'_1 \) rises. Which happens first?
(a) The old fault slips at \( \sigma'_1 \approx 62 \) MPa (b) The old fault slips at \( \sigma'_1 \approx 106 \) MPa (c) A new optimally oriented fault forms at \( \sigma'_1 \approx 98 \) MPa, before the old fault slips (d) Neither, because the old fault is locked
Answer: (c)
Old fault: \( R = \frac{1 + 0.6\cot 50°}{1 - 0.6\tan 50°} = \frac{1 + 0.503}{1 - 0.715} \approx 5.28 \), so slip needs \( \sigma'_1 = 5.28\times 20 \approx 106 \) MPa.
Intact rock: \( \tan(45° + 15.5°) \approx 1.766 \); \( \sigma'_1 = 20\times 3.12 + 2\times 10\times 1.766 \approx 62.4 + 35.3 \approx 97.7 \) MPa.
The new fault forms first, at about 98 MPa. Option (a) wrongly uses the optimal ratio 3.12 for the misoriented fault. The fault at 50° is not locked (lock-up is at 59°), so (d) is wrong. With a little more fluid pressure or a slightly weaker fault, the answer could flip; that sensitivity is why misoriented faults that slip point to overpressure.
Practice Q9. In a region, \( \sigma_1 = 100 \) MPa, \( \sigma_3 = 40 \) MPa, \( P_f = 20 \) MPa. Four cohesionless faults, all containing \( \sigma_2 \), make the angles below with \( \sigma_1 \). Their sliding friction is 0.6.
| Fault | Angle to \( \sigma_1 \) |
|---|---|
| F1 | 15° |
| F2 | 30° |
| F3 | 50° |
| F4 | 70° |
Which faults are at or past the point of slip?
(a) F2 only (b) F1 and F2 only (c) F1, F2 and F3 (d) all four
Answer: (b) F1 and F2 only
Centre 70 MPa, radius 30 MPa. For each fault, the normal angle is \( 90° - \) (fault angle).
| Fault | \( \sigma_n \) (MPa) | \( \tau \) (MPa) | \( \sigma'_n \) | \( T_s = \tau/\sigma'_n \) |
|---|---|---|---|---|
| F1 (15°) | 44.0 | 15.0 | 24.0 | 0.62 |
| F2 (30°) | 55.0 | 26.0 | 35.0 | 0.74 |
| F3 (50°) | 75.2 | 29.5 | 55.2 | 0.54 |
| F4 (70°) | 93.0 | 19.3 | 73.0 | 0.26 |
F1 and F2 exceed 0.6 and slip. F3 has the highest shear stress but also high normal stress, so its slip tendency is below 0.6. Large \( \tau \) alone does not mean slip.
Practice Q10. Which of these statements are correct?
- Raising pore pressure moves the Mohr circle towards lower normal stress without changing its diameter.
- Pure extension fractures can form at depth only if the effective least principal stress reaches the negative of the tensile strength.
- Under Byerlee’s law, a clay-rich gouge and a granite fault surface have the same friction coefficient.
- A steep reverse fault that slips repeatedly with crack–seal quartz veining is consistent with fault-valve behaviour.
(a) 1 and 2 only (b) 1, 2 and 4 only (c) 2, 3 and 4 only (d) 1, 2, 3 and 4
Answer: (b) 1, 2 and 4 only
- 1 true: effective stresses fall by \( P_f \); the differential stress is unchanged.
- 2 true: the tensile criterion is \( \sigma'_3 = -T \); at depth that needs high \( P_f \).
- 3 false: Byerlee’s law holds for most rocks, but clay minerals (especially smectite) are a known exception and are much weaker.
- 4 true: badly oriented reverse faults need near-lithostatic fluid pressure, and rupture–drain–seal cycles give crack–seal veins.
Quick Revision Table
| Idea | Fact or formula |
|---|---|
| Mohr equations | \( \sigma_n = \frac{\sigma_1+\sigma_3}{2} + \frac{\sigma_1-\sigma_3}{2}\cos 2\theta \), \( \tau = \frac{\sigma_1-\sigma_3}{2}\sin 2\theta \); \( \theta \) from \( \sigma_1 \) to the normal |
| 3D Mohr | three circles; \( \tau_{\max} = (\sigma_1 - \sigma_3)/2 \) on planes containing \( \sigma_2 \) |
| Stress ratio | \( \Phi = (\sigma_2 - \sigma_3)/(\sigma_1 - \sigma_3) \) |
| Griffith | \( \sigma_c = \sqrt{2E\gamma/\pi a} \); envelope \( \tau^2 = 4T(\sigma_n + T) \); UCS \( = 8T \) (2D) |
| Fracture modes | I opening, II sliding, III tearing |
| Coulomb | \( \tau = C + \mu\sigma_n \); fracture at \( 45° - \phi/2 \) to \( \sigma_1 \) |
| Coulomb in principal stresses | \( \sigma_1 = \sigma_3\tan^2(45° + \phi/2) + 2C\tan(45° + \phi/2) \) |
| Extension / hybrid / shear | \( \Delta\sigma < 4T \) / \( 4T \)–\( 5.66T \) / \( > 5.66T \) |
| Byerlee | \( 0.85\sigma_n \) (< 200 MPa); \( 50 + 0.6\sigma_n \) (200–1,700 MPa) |
| Effective stress | \( \sigma' = \sigma - P_f \); \( \lambda_v = P_f/\sigma_v \); hydrostatic about 0.4 |
| Reactivation | \( R = (1 + \mu_s\cot\theta_r)/(1 - \mu_s\tan\theta_r) \); optimum \( \approx 29.5° \), \( R^* \approx 3.12 \); lock-up \( \approx 59° \) (\( \mu_s = 0.6 \)) |
| Slip / dilation tendency | \( T_s = \tau/\sigma'_n \); \( T_d = (\sigma_1 - \sigma_n)/(\sigma_1 - \sigma_3) \) |
| Stress indicators | breakouts along \( \sigma_{h\min} \); tensile fractures along \( \sigma_{H\max} \); shut-in pressure gives \( \sigma_{h\min} \) |
Key Takeaways
What’s Next
- Strain Ellipsoid, Tectonic Fabrics and Strain Analysis: from the forces to the shape change they produce.
- Deformation Mechanisms and Shear Zones: what happens below the brittle field, where Coulomb and Byerlee stop applying.
- Back to the Structural Geology and Geotectonics chapter overview.