Logging Operations: Open-Hole, Cased-Hole, Production Logging and LWD
Borehole environment, invasion zones, open-hole and cased-hole suites, cement bond and pulsed-neutron logs, production logging and LWD for CSIR NET.
- 25 min
On this page · 15 sections
Prerequisites
- Petroleum Geology and Indian Basins — reservoirs, seals, traps and the exploration sequence that ends with a drilled well. Its short wireline-log table is the starting point for this chapter.
- Hydrogeology: Darcy’s Law, Aquifers, Groundwater Exploration and Pollution — porosity, permeability and Darcy flow, which production logging measures in a well.
- Radioactive Decay and Selection Rules — gamma rays and neutrons, the physics behind the nuclear tools mentioned here and explained on the porosity-log page.
The Hook: A Well That Has to Be Logged Three Times
How CSIR NET asks it. Well logging sits in the Geophysics section of Part C. From this page expect: which logs work in which hole and mud condition; the invasion profile and the symbols \( R_m, R_{mf}, R_{xo}, R_t, R_w \); reading a cement bond log; production-logging arithmetic (zone contributions from spinner readings, water holdup from fluid density); saturation from a pulsed-neutron sigma log; and comparisons of LWD with wireline.
What a Well Log Is
A well log (geophysical log) is a continuous record, against depth, of a physical property of the rocks and fluids around a borehole. Each curve is a property (resistivity, natural radioactivity, bulk density, transit time, temperature) measured by a sonde that moves along the hole. The log replaces most of what a continuous core would tell you, at a fraction of the cost, and it is the main source of porosity, fluid saturation, lithology and correlation in the subsurface.
Logs are classified in three ways, and examiners mix the three:
| Classification | Categories |
|---|---|
| By time of acquisition | logging while drilling (LWD); open-hole wireline after drilling; cased-hole after casing is set; production logging in a flowing or injecting well |
| By physics | electrical (SP, resistivity), acoustic (sonic, cement bond), nuclear (gamma ray, density, neutron, pulsed neutron), thermal (temperature), mechanical (caliper, spinner), magnetic resonance (NMR) |
| By purpose | correlation and lithology (GR, SP); porosity (sonic, density, neutron); fluid saturation (resistivity, pulsed neutron); well integrity (cement bond, casing inspection); flow (spinner, temperature, fluid density) |
Wireline acquisition in one paragraph
A logging unit (a truck onshore, a cabin offshore) holds a winch and an armoured logging cable with insulated conductors. The cable carries power down and data up, and its length, measured at the surface, gives depth. Tools are lowered to the bottom and most measurements are made while pulling up, because the cable is then under steady tension and depth is more reliable. Several sondes are screwed together into one tool string so that one run records many curves at the same depth. Logs are displayed on a standard log sheet: depth in the middle, correlation curves (GR, SP, caliper) in the left track, resistivity (usually on a logarithmic scale) and porosity curves in the right tracks.
The Borehole Environment
Every open-hole log is made through, or around, the effects of drilling. The well is drilled with drilling mud, kept slightly heavier than formation pressure so that formation fluids do not flow into the hole. Opposite a permeable bed, mud pressure pushes the liquid part of the mud (mud filtrate) into the formation; the solids are left on the wall as a mud cake. The filtrate displaces some or all of the movable fluid near the hole. This is invasion.
graph LR
A["Borehole
mud Rm
diameter dh"] --> B["Mud cake
Rmc, thickness hmc"]
B --> C["Flushed zone
filtrate Rmf
rock Rxo, Sxo"]
C --> D["Transition zone
mixed fluids
Ri, out to diameter di"]
D --> E["Uninvaded zone
formation water Rw
rock Rt, Sw"]| Symbol | Meaning |
|---|---|
| \( R_m \) | resistivity of the mud in the hole |
| \( R_{mc} \) | resistivity of the mud cake |
| \( R_{mf} \) | resistivity of the mud filtrate |
| \( R_{xo} \) | resistivity of the flushed zone (rock + filtrate + residual hydrocarbon) |
| \( R_i \) | resistivity of the transition (invaded) zone |
| \( R_t \) | true resistivity of the uninvaded formation |
| \( R_w \) | resistivity of the formation water |
| \( R_s \) | resistivity of the adjacent (shoulder) bed, usually shale |
| \( S_{xo} \), \( S_w \) | water saturation of the flushed and uninvaded zones |
| \( d_h \), \( d_i \) | hole diameter; diameter of invasion |
Three consequences drive log design:
- Shallow and deep readings differ. A shallow-reading tool sees mostly the flushed zone (\( R_{xo} \)); a deep-reading tool sees mostly the uninvaded zone (\( R_t \)). Running shallow, medium and deep resistivity together lets the analyst correct for invasion and estimate \( R_t \), \( R_{xo} \) and \( d_i \).
- Mud cake is evidence of permeability. Mud cake forms only where filtrate can enter the rock. A caliper reading slightly smaller than bit size opposite a sand, and separation on micro-resistivity curves, are qualitative permeability indicators (see Electrical, SP and Temperature Logs).
- The mud type limits the tools. Electrical current needs a conductive path between the tool and the rock.
Which tools work in which hole
| Hole condition | Works | Fails or degraded | Why |
|---|---|---|---|
| Water-based (conductive) mud | SP, laterolog, induction (if mud not very salty), all nuclear and acoustic tools | induction degraded in very salty mud | SP and laterolog need current flow through the mud |
| Oil-based (non-conductive) mud | induction, nuclear, acoustic | SP, laterolog, conventional electrode tools | no conductive path in the mud |
| Air- or gas-filled hole | induction, gamma ray, density, neutron (with corrections) | SP, laterolog, sonic | no conductive liquid; sonic needs liquid to couple sound into the wall |
| Cased hole (steel) | gamma ray, neutron, pulsed neutron, sonic and cement tools, temperature | SP, conventional resistivity, induction, conventional density (casing and cement absorb the gamma rays) | steel short-circuits current and screens electromagnetic fields |
Open-Hole Logging
Open-hole logs are run after a section of the hole is drilled and before casing is set. They are the main formation-evaluation data set.
The standard suite
| Log | Measures | Main use | Detailed on |
|---|---|---|---|
| Caliper | hole diameter | washouts, mud cake, tool corrections, cement volume | this page |
| Gamma ray (GR) | natural gamma radioactivity | shale volume, correlation | Porosity Logs |
| Spontaneous potential (SP) | natural potential against a surface electrode | permeable beds, \( R_w \), shale volume | Electrical, SP and Temperature Logs |
| Resistivity (shallow, medium, deep) | formation resistivity at several depths of investigation | \( R_t \), \( R_{xo} \), invasion, hydrocarbons | Electrical logs page |
| Density (with Pe) | bulk density, photoelectric factor | porosity, lithology | Porosity Logs |
| Neutron | hydrogen index | porosity, gas detection | Porosity Logs |
| Sonic | interval transit time \( \Delta t \) | porosity, seismic tie, mechanical properties | Porosity Logs |
| Temperature | borehole temperature | gradient, formation temperature for corrections | Electrical logs page |
A typical first run combines GR, SP, caliper and resistivity; a second combines density, neutron, sonic and GR (the GR on every run is used to match depths between runs). Specialised open-hole services include:
- Dipmeter and borehole image logs: several micro-resistivity pads (or an ultrasonic scanner) record the wall around the hole. Planes cut by the hole appear as sine curves on an unrolled image; the amplitude and phase of the sine give dip and dip direction of beds, fractures and faults.
- Nuclear magnetic resonance (NMR): measures the relaxation of hydrogen nuclei in pore fluids; the relaxation-time distribution reflects pore-size distribution, giving porosity independent of lithology, bound versus free fluid, and a permeability estimate.
- Formation testers: a probe pressed against the wall measures formation pressure at chosen depths and can take fluid samples. Pressure plotted against depth gives fluid gradients and fluid contacts.
- Sidewall cores: small plugs cut or shot from the wall at chosen depths.
Open-hole corrections
Before quantitative use, readings are corrected for the borehole (diameter, mud weight and resistivity, mud cake, tool stand-off), for the shoulder beds above and below thin beds, and for invasion. Service companies publish chart books for these corrections; in an exam you are told the corrected value or asked which correction a given condition needs.
Cased-Hole Logging
Once steel casing is cemented in, the electrical and most short-range tools are blind. What remains possible:
| Purpose | Log | Principle |
|---|---|---|
| Depth control | Gamma ray + casing collar locator (CCL) | GR matches the open-hole GR; the CCL (a magnetic sensor) marks the thicker steel at casing joints. Perforating guns are positioned this way. |
| Cement evaluation | Cement bond log (CBL) with variable density log (VDL); ultrasonic pulse-echo tools | acoustic coupling of casing to cement and cement to formation |
| Porosity behind casing | cased-hole neutron, cased-hole sonic (where bonded) | neutrons and well-coupled sound pass through steel |
| Saturation monitoring | pulsed-neutron capture (sigma); carbon/oxygen (C/O) logging; through-casing resistivity | neutron capture by chlorine; inelastic gamma rays of carbon and oxygen |
| Casing condition | multi-finger caliper; electromagnetic thickness tools; ultrasonic imagers | internal radius; metal loss from corrosion or wear |
Cement bond log
A sonic transmitter fires; a receiver about 3 ft (0.9 m) away records the amplitude of the first arrival, which travels along the casing. A second receiver about 5 ft (1.5 m) away records the full waveform, displayed as a variable density log (VDL), in which positive peaks are shaded dark.
| Situation | CBL amplitude | VDL appearance |
|---|---|---|
| Free pipe (no cement) | high: the casing rings freely | strong, straight, parallel casing arrivals; chevron patterns at collars; no formation arrivals |
| Good bond to casing and formation | low: energy leaks into the cement and rock | weak casing arrivals; strong, wavy formation arrivals that follow lithology |
| Bonded to casing, not to formation | low | weak casing arrivals and weak or no formation arrivals |
| Microannulus (thin gap between casing and cement) | moderately high; falls when the casing is pressured | casing arrivals visible |
| Channel (mud channel through cement) | intermediate | mixed |
The CBL averages around the circumference, so it cannot by itself tell a uniformly poor bond from a narrow channel. Ultrasonic pulse-echo tools rotate a transducer, excite a thickness resonance in the casing wall, and map the acoustic impedance of whatever is behind the steel all round the hole: a cement map that shows channels directly.
Pulsed-neutron capture (sigma) logging
A neutron generator emits a short burst of high-energy neutrons. They slow down and are captured by nuclei; the thermal-neutron population decays with time, and the decay rate measures the formation’s macroscopic thermal-neutron capture cross-section \( \Sigma \) (sigma), in capture units (c.u.). Chlorine has a very large capture cross-section, so saline formation water has a high \( \Sigma \), while oil and gas have low values. Sigma mixes linearly by volume:
$$\boxed{\Sigma_{\log} = (1 - \phi)\,\Sigma_{ma} + \phi\,S_w\,\Sigma_w + \phi\,(1 - S_w)\,\Sigma_h}$$Solve for \( S_w \):
$$S_w = \frac{(\Sigma_{\log} - \Sigma_{ma}) - \phi\,(\Sigma_h - \Sigma_{ma})}{\phi\,(\Sigma_w - \Sigma_h)}$$(the same result as writing \( \Sigma_{\log} - (1-\phi)\Sigma_{ma} = \phi[S_w\Sigma_w + (1 - S_w)\Sigma_h] \)). Porosity comes from the open-hole logs; \( \Sigma_w \) from the salinity of the formation water. The method works best when formation water is saline (large \( \Sigma_w - \Sigma_h \)) and porosity is not small. Repeating the log every year or two (time-lapse) shows the oil–water contact rising as the reservoir is produced.
Carbon/oxygen logging uses the same neutron burst but counts the inelastic gamma rays emitted during fast collisions, at energies characteristic of carbon (about 4.4 MeV) and oxygen (about 6.1 MeV). Oil is rich in carbon, water in oxygen, so the C/O ratio indicates oil saturation independently of water salinity. It is the choice when formation water is fresh or of unknown salinity (sigma contrast too small), at the cost of a shallower reading and slower logging.
Production Logging
Production logging (PL) measures the fluids moving inside a completed well, under flowing or shut-in conditions. Questions it answers: which perforated zones produce (or take injected fluid), at what rates, which fluids each zone gives, whether there is flow behind the casing or crossflow between zones in a shut-in well, and where water or gas is breaking through.
The production-logging tool string
| Sensor | Measures | Use |
|---|---|---|
| Spinner flowmeter (continuous or full-bore) | impeller revolutions per second, roughly proportional to fluid velocity relative to the tool | velocity and flow-rate profile |
| Temperature | fluid temperature | entries (anomalies from the geothermal gradient), flow behind casing, gas entry (cooling on expansion) |
| Pressure | absolute pressure | inflow performance, reservoir pressure, gradients |
| Fluid density (gradiomanometer, or nuclear densitometer) | mixture density | phase holdup in two-phase flow |
| Capacitance / holdup tools | dielectric response (water versus hydrocarbon) | water holdup |
| Noise log | sound amplitude in frequency bands | flow through channels and leaks, gas bubbling through liquid |
| GR and CCL | depth control | tie to perforations and open-hole logs |
| Radioactive tracer | arrival of a tracer slug | injection profiles in injector wells |
Spinner analysis
The spinner turns at a rate proportional to the velocity of the fluid relative to the tool. Several passes are logged up and down at different cable speeds; in a zone of no flow (below the bottom perforation) the plot of spinner speed against cable speed gives the tool’s calibration line. In a flowing interval the line shifts, and the intercept gives the apparent fluid velocity \( v_a \) (the velocity near the centre of the pipe, where the spinner sits).
The average velocity across the pipe is smaller than the centreline velocity:
$$\boxed{\bar v = C\,v_a, \qquad Q = \bar v\,A}$$where \( A \) is the internal cross-sectional area and \( C \) the velocity profile correction factor: about 0.83 for turbulent flow (flat profile) and 0.5 for fully laminar flow (parabolic profile, mean equals half the centreline value).
Zone contributions come from differences. Flow measured above a zone minus flow measured below it is what that zone contributes. Because \( C \) and \( A \) are the same along a constant-diameter pipe, percentage contributions can be read directly from velocity differences, without converting to rates.
Holdup from fluid density
In two-phase flow (say oil and water), the holdup \( y_w \) is the fraction of the pipe cross-section occupied by water at a depth. The measured mixture density is a volume-weighted average:
$$\rho_m = y_w\,\rho_w + (1 - y_w)\,\rho_o \quad\Longrightarrow\quad \boxed{y_w = \frac{\rho_m - \rho_o}{\rho_w - \rho_o}}$$A gradiomanometer gets \( \rho_m \) from the pressure difference between two sensors a known distance apart (corrected for friction and well deviation). Holdup is not the same as the water cut (the fraction of the flow rate that is water): in an upward-flowing well the lighter oil moves faster than the water (slippage), so the water holdup is larger than the water cut.
Temperature in production logging
Away from flow, temperature follows the geothermal gradient. A fluid entering the well arrives at the temperature of its zone and mixes with the stream, changing its temperature; liquid entering from below brings warmer fluid up. Gas entry produces cooling, because gas expanding through the perforations cools (Joule–Thomson effect). A shut-in temperature log that departs from the geothermal line between two zones indicates flow behind the casing. Temperature physics is developed on the electrical, SP and temperature page.
Logging While Drilling (LWD)
Measurement while drilling (MWD) and logging while drilling (LWD) place sensors in thick-walled drill collars just behind the bit, so the formation is measured minutes to hours after it is cut.
| Term | Measurements | Purpose |
|---|---|---|
| MWD | inclination, azimuth, tool-face, downhole weight and torque, shock and vibration, annular pressure | directional control and drilling efficiency |
| LWD | gamma ray (often azimuthal), propagation and laterolog-type resistivity, density with Pe, neutron, sonic, NMR, formation pressure, borehole images | formation evaluation, geosteering |
Getting data to the surface
- Mud-pulse telemetry: a valve in the drill string modulates the pressure of the circulating mud; pressure transducers at the surface decode the pulses. It is the standard method, but slow: only a selected subset of data is sent in real time.
- Electromagnetic telemetry: low-frequency signals through the rock to surface electrodes; useful when mud cannot carry pulses (air or foam drilling), limited by depth and formation resistivity.
- Wired drill pipe: conductors built into each joint of pipe; far higher data rates.
- Downhole memory: the full-resolution data are stored in the tool and read when the string is pulled out of the hole.
LWD resistivity
The commonest LWD resistivity tool is an electromagnetic propagation tool: transmitters on the collar send a wave (frequencies of the order of 2 MHz, often with a lower second frequency) and two receivers measure the phase shift and the attenuation between them. Both convert to resistivity. Phase-shift resistivity reads shallower with better vertical resolution; attenuation resistivity reads deeper. The pair works like a shallow and deep log for invasion analysis. Because the measurement is inductive it works in oil-based mud; in very resistive formations, laterolog-type resistivity-at-bit tools are used instead.
LWD versus wireline
| Feature | LWD | Wireline (open hole) |
|---|---|---|
| Time after drilling | minutes to hours (time after bit = sensor offset ÷ rate of penetration) | days |
| Invasion | little; close to virgin formation | may be deep |
| High-angle and horizontal wells | natural: the tools ride on the drill pipe | needs pipe-conveyed or tractor conveyance |
| Real-time decisions | geosteering, casing-point picking, pore-pressure monitoring | none |
| Sampling density | depends on rate of penetration and memory | uniform, set by logging speed |
| Data rate to surface | low (mud pulse) unless wired pipe | high |
| Risk | no extra trip; data even if the hole later collapses | tool can stick in a bad hole |
| Borehole images | from rotation: azimuthal density, GR and resistivity sectors | from pads or rotating sensors |
Time-lapse logging (comparing LWD logs with a later wireline run, or with logs recorded on a later trip) shows how invasion develops and helps separate permeable from tight beds.
Memory Tricks
Don’t Confuse
| Pair | First | Second |
|---|---|---|
| \( R_{mf} \) vs \( R_{xo} \) | resistivity of the filtrate itself | resistivity of the rock in the flushed zone (rock + filtrate + residual hydrocarbon) |
| \( R_t \) vs \( R_w \) | resistivity of the uninvaded rock | resistivity of the formation water alone |
| MWD vs LWD | directional and drilling-mechanics data | formation-evaluation logs |
| CBL vs VDL | amplitude of the first (casing) arrival | full waveform, showing casing and formation arrivals |
| Sigma log vs C/O log | thermal-neutron capture; needs saline water | inelastic gamma ratio; salinity-independent |
| Holdup vs water cut | fraction of pipe area occupied by water | fraction of flow rate that is water |
| Open-hole vs production logging | properties of rock and pore fluids | fluids moving inside the well |
| Depth of investigation vs vertical resolution | how far into the formation the tool reads | the thinnest bed it can resolve |
Common Mistakes
Practice
All questions below are original practice questions written for this page. They are not from any CSIR NET paper.
Level 1: Foundation
- Name the zone whose resistivity is written \( R_{xo} \).
- Which two standard open-hole logs cannot be run in an oil-based-mud well?
- What does a casing collar locator record, and why is it run with a gamma-ray log in cased hole?
Answers
- The flushed zone, next to the borehole wall, where mud filtrate has displaced the movable formation fluids.
- The SP and the laterolog (and other conventional electrode resistivity devices): both need current to flow through a conductive mud. Induction is used instead.
- It detects the thicker steel at casing joints magnetically. Collar depths plus a GR that matches the open-hole GR give exact depth control for perforating.
Level 2: Part B Style
Practice Q1. On a cement bond log, a zone shows a very low first-arrival amplitude and strong, wavy late arrivals on the VDL that change with lithology. The most likely interpretation is:
(a) free pipe (b) good bond to both casing and formation (c) microannulus (d) cement bonded to casing but not to formation
Answer: (b)
Low casing amplitude means the casing is well coupled to cement; strong formation arrivals on the VDL mean the sound is also crossing into the rock, so the cement is bonded to the formation too. (a) gives high amplitude and straight casing arrivals. (c) gives a relatively high amplitude that falls when the casing is pressured. (d) gives low amplitude but weak or absent formation arrivals.
Practice Q2. An LWD resistivity sensor is 12 m behind the bit, and the rate of penetration is 15 m/h. The time after bit for the measurement is:
(a) 0.8 h (b) 1.25 h (c) 3 h (d) 180 h
Answer: (a) 0.8 h
Time after bit = sensor offset ÷ rate of penetration = 12/15 = 0.8 h (48 minutes). (b) inverts the ratio. (c) subtracts the two numbers. (d) multiplies them. The short time is why LWD resistivity often reads close to virgin formation.
Practice Q3. In an oil–water production well, a gradiomanometer reads a mixture density of 0.94 g/cm³. Water density is 1.05 g/cm³ and oil density 0.80 g/cm³ at downhole conditions. The water holdup is:
(a) 0.44 (b) 0.56 (c) 0.89 (d) 0.94
Answer: (b) 0.56
\( y_w = (\rho_m - \rho_o)/(\rho_w - \rho_o) = (0.94 - 0.80)/(1.05 - 0.80) = 0.14/0.25 = 0.56 \). (a) is the oil holdup \( 1 - y_w \). (c) is \( 0.94/1.05 \), ignoring the oil. (d) mistakes the density for a fraction. Remember the water cut at surface will be lower than 0.56 because oil slips past water.
Practice Q4. Which statement about carbon/oxygen (C/O) logging is correct?
(a) It measures thermal-neutron capture by chlorine (b) It works only when formation water is highly saline (c) It uses inelastic gamma rays, so the oil-saturation estimate is independent of water salinity (d) It must be run in open hole because steel absorbs the gamma rays
Answer: (c)
C/O logging counts gamma rays from inelastic scattering of fast neutrons by carbon and oxygen nuclei; their ratio reflects oil versus water and does not depend on salinity. (a) and (b) describe the sigma (capture) log. (d) is wrong: C/O is a cased-hole saturation-monitoring method.
Level 3: Part C Style
Practice Q5. A producing well has three perforated zones, A (top), B and C (bottom), in casing of internal diameter 0.15 m. After calibration, apparent fluid velocities are 0.80 m/s above A, 0.50 m/s between A and B, 0.20 m/s between B and C, and zero below C. Flow is turbulent (profile factor 0.83). Which option gives the total rate and the contribution of zone B?
(a) about 1,014 m³/day; 37.5% (b) about 1,221 m³/day; 37.5% (c) about 1,014 m³/day; 62.5% (d) about 634 m³/day; 30%
Answer: (a)
Area \( = \pi(0.075)^2 = 0.017671 \) m². Average velocity above A \( = 0.83 \times 0.80 = 0.664 \) m/s. \( Q = 0.664 \times 0.017671 = 0.011734 \) m³/s \( \times 86{,}400 = 1{,}013.8 \) m³/day.
Zone B contributes the flow between A and B minus the flow below B: \( (0.50 - 0.20)/0.80 = 0.375 = 37.5\% \).
(b) omits the 0.83 factor (\( 0.80 \times 0.017671 \times 86{,}400 = 1{,}221 \)). (c) takes the flow between A and B (0.50/0.80) as zone B’s share; that is B plus C. (d) uses the velocity between A and B for the total rate.
Practice Q6. A cased sandstone reservoir has porosity 0.25 (from open-hole logs). A pulsed-neutron log reads \( \Sigma_{\log} = 22 \) c.u. Take \( \Sigma_{ma} = 8 \), \( \Sigma_w = 80 \) and \( \Sigma_h = 20 \) c.u. The water saturation is closest to:
(a) 0.03 (b) 0.60 (c) 0.73 (d) 0.80
Answer: (c) 0.73
\( \Sigma_{\log} = (1 - \phi)\Sigma_{ma} + \phi[S_w\Sigma_w + (1 - S_w)\Sigma_h] \).
\( 22 = 0.75 \times 8 + 0.25[80S_w + 20(1 - S_w)] = 6 + 0.25(60S_w + 20) = 6 + 15S_w + 5 \).
So \( 15S_w = 11 \) and \( S_w = 0.733 \). If an earlier survey gave a lower \( S_w \) at the same depth, the zone is watering out.
Each wrong option drops or mis-weights one term. (d): leaving out the hydrocarbon term gives \( 22 = 6 + 0.25 \times 80S_w \), so \( S_w = 0.80 \). (b): using the full matrix value 8 instead of \( (1 - \phi) \times 8 = 6 \) gives \( 22 = 8 + 15S_w + 5 \), so \( S_w = 0.60 \). (a): ignoring the rock altogether, \( 22 = 20 + 60S_w \), gives \( S_w = 0.03 \).
Practice Q7. Consider these statements:
- LWD resistivity usually shows less invasion effect than a wireline log run days later in the same well.
- Phase-shift resistivity from a propagation tool reads deeper than attenuation resistivity at the same frequency.
- A shut-in temperature log that departs from the geothermal gradient between two perforated zones can indicate crossflow or flow behind casing.
- A low-amplitude CBL by itself proves there is no channel in the cement.
Which are correct?
(a) 1 and 3 only (b) 1, 2 and 3 only (c) 2 and 4 only (d) 1, 3 and 4 only
Answer: (a) 1 and 3 only
- True. The sensor passes the formation minutes to hours after the bit, before filtrate has moved far.
- False. Phase-shift resistivity is the shallower, higher-resolution reading; attenuation reads deeper.
- True. In a shut-in well, temperature should lie on the geothermal line; moving fluid carries heat and distorts it.
- False. The CBL averages around the circumference; a narrow channel can coexist with a fairly low average amplitude. Ultrasonic cement maps are needed to see channels.
Quick Revision Table
| Idea | Fact |
|---|---|
| Zones outward | mud \( R_m \) → mud cake \( R_{mc} \) → flushed \( R_{xo} \) → transition \( R_i \) → uninvaded \( R_t \) |
| Mud cake | forms only opposite permeable beds; caliper slightly under bit size |
| Oil-based mud | no SP, no laterolog; use induction |
| Air-filled hole | no SP, laterolog or sonic |
| Cased hole | GR, CCL, neutron, pulsed neutron, sonic and cement tools, temperature |
| CBL | low amplitude = good bond; VDL shows formation arrivals when bonded |
| Sigma | \( \Sigma = (1-\phi)\Sigma_{ma} + \phi S_w\Sigma_w + \phi(1-S_w)\Sigma_h \); needs saline water |
| C/O | inelastic gamma, about 4.4 MeV (C) and 6.1 MeV (O); salinity-independent |
| Spinner | \( Q = C v_a A \); \( C \approx 0.83 \) turbulent, 0.5 laminar; zone share = above − below |
| Holdup | \( y_w = (\rho_m - \rho_o)/(\rho_w - \rho_o) \); holdup > water cut in upflow |
| Gas entry | cooling anomaly (Joule–Thomson) |
| MWD / LWD | steering data / formation evaluation behind the bit |
| Telemetry | mud pulse (slow), EM, wired pipe; memory for full data |
| Propagation resistivity | phase shift shallow; attenuation deep |
Key Takeaways
What’s Next
- Electrical, SP and Temperature Logs: how resistivity tools see through invasion, where the SP comes from, and what temperature logs record.
- Porosity Logs: Sonic, Density, Neutron and Gamma Ray: the physics of the porosity and radioactivity tools.
- Auto- and Cross-Correlation and LTI Systems: cross-correlation is also how log curves are depth-matched between runs and wells.
- Well Logging: back to the chapter overview.