Skip to content

Transmission Lines and Waveguides

CSIR NET guided waves: telegrapher's equations, impedance, reflection, VSWR, quarter-wave matching, TE/TM modes, cut-off and cavities.

  • 19 min read
  • Updated
On this page · 11 sections
  1. Prerequisites
  2. The Hook: Why Your Cable Has a Number Printed on It
  3. Part 1: Transmission Lines
  4. Part 2: Waveguides
  5. Memory Tricks
  6. Don’t Confuse
  7. Common Mistakes
  8. Practice
  9. Quick Revision Table
  10. Key Takeaways
  11. What’s Next

Prerequisites

The Hook: Why Your Cable Has a Number Printed on It

Part 1: Transmission Lines

The distributed model

A line is described per unit length by series resistance \( R \) and inductance \( L \), shunt conductance \( G \) and capacitance \( C \). Kirchhoff’s laws on a short element \( dz \) give the telegrapher’s equations:

$$\frac{\partial V}{\partial z} = -RI - L\frac{\partial I}{\partial t}, \qquad \frac{\partial I}{\partial z} = -GV - C\frac{\partial V}{\partial t}$$

With phasors \( V(z)e^{j\omega t} \) (the engineering convention used on this page; physics texts write \( e^{-i\omega t} \), which replaces \( j \) by \( -i \)):

$$\frac{d^2V}{dz^2} = \gamma^2V, \qquad \boxed{\gamma = \alpha + j\beta = \sqrt{(R + j\omega L)(G + j\omega C)}}, \qquad \boxed{Z_0 = \sqrt{\frac{R + j\omega L}{G + j\omega C}}}$$

The general solution is \( V(z) = V^+e^{-\gamma z} + V^-e^{\gamma z} \), with currents \( I = (V^+e^{-\gamma z} - V^-e^{\gamma z})/Z_0 \). \( Z_0 \) is the voltage-to-current ratio of a single travelling wave.

Special cases

LineCondition\( Z_0 \)Propagation
Lossless\( R = G = 0 \)\( \sqrt{L/C} \), real\( \alpha = 0 \), \( \beta = \omega\sqrt{LC} \), \( v = 1/\sqrt{LC} \)
Low loss\( R \ll \omega L \), \( G \ll \omega C \)\( \approx\sqrt{L/C} \)\( \alpha \approx \dfrac{R}{2Z_0} + \dfrac{GZ_0}{2} \)
Distortionless (Heaviside)\( R/L = G/C \)\( \sqrt{L/C} \), real\( \alpha = \sqrt{RG} \), \( v = 1/\sqrt{LC} \), both frequency-independent

On a distortionless line every frequency travels at the same speed and decays at the same rate, so a pulse shrinks without changing shape. Real telephone cables have \( G/C \ll R/L \); historically, inductance was added to approach the condition.

Standard geometries

For any TEM line in a uniform dielectric, \( LC = \mu\varepsilon \), so \( v = 1/\sqrt{\mu\varepsilon} = c/\sqrt{\varepsilon_r} \) (non-magnetic).

Line\( L \) per length\( C \) per length\( Z_0 \) (non-magnetic)
Coaxial (radii \( a < b \))\( \dfrac{\mu}{2\pi}\ln\dfrac{b}{a} \)\( \dfrac{2\pi\varepsilon}{\ln(b/a)} \)\( \dfrac{60}{\sqrt{\varepsilon_r}}\ln\dfrac{b}{a} \) Ω
Two-wire (radius \( a \), centre spacing \( d \))\( \dfrac{\mu}{\pi}\cosh^{-1}\dfrac{d}{2a} \)\( \dfrac{\pi\varepsilon}{\cosh^{-1}(d/2a)} \)\( \dfrac{120}{\sqrt{\varepsilon_r}}\cosh^{-1}\dfrac{d}{2a} \approx \dfrac{120}{\sqrt{\varepsilon_r}}\ln\dfrac{d}{a} \) Ω (\( d \gg a \))
Parallel plate (width \( w \gg \) gap \( h \))\( \mu h/w \)\( \varepsilon w/h \)\( \eta\,h/w \)

The 60 and 120 come from \( \eta_0/2\pi \approx 60 \) Ω and \( \eta_0/\pi \approx 120 \) Ω, with \( \eta_0 = \sqrt{\mu_0/\varepsilon_0} \approx 376.7 \) Ω.

Reflection at a load

At the load (\( z = 0 \)), \( V/I = Z_L \). The reflection coefficient is

$$\boxed{\Gamma_L = \frac{V^-}{V^+} = \frac{Z_L - Z_0}{Z_L + Z_0}}$$
Load\( \Gamma_L \)What comes back
Matched, \( Z_L = Z_0 \)0nothing
Short, \( Z_L = 0 \)\( -1 \)inverted pulse (voltage node at load)
Open, \( Z_L = \infty \)\( +1 \)upright pulse (voltage antinode at load)
Pure reactance \( jX \)\( \vert \Gamma\vert = 1 \), phase shifteverything, delayed in phase

The voltage transmitted into the load is \( (1 + \Gamma_L)V^+ \). Power reflected is \( |\Gamma|^2 \) of the incident power; power delivered is \( 1 - |\Gamma|^2 \) (lossless line, real \( Z_0 \)).

Standing waves and VSWR

Incident and reflected waves form a partial standing wave with

$$|V|_{\max} = |V^+|(1 + |\Gamma|), \qquad |V|_{\min} = |V^+|(1 - |\Gamma|), \qquad \boxed{S = \text{VSWR} = \frac{1 + |\Gamma|}{1 - |\Gamma|}}$$

Adjacent maxima (or minima) are \( \lambda/2 \) apart; a maximum and the next minimum are \( \lambda/4 \) apart. Inverting, \( |\Gamma| = (S - 1)/(S + 1) \). For a real load, \( S = Z_L/Z_0 \) if \( Z_L > Z_0 \) and \( Z_0/Z_L \) otherwise.

Input impedance

Looking into a lossless line of length \( l \) terminated in \( Z_L \):

$$\boxed{Z_{\text{in}} = Z_0\,\frac{Z_L + jZ_0\tan\beta l}{Z_0 + jZ_L\tan\beta l}}$$
Case\( Z_{\text{in}} \)Use
Short-circuited stub\( jZ_0\tan\beta l \)inductive for \( l < \lambda/4 \): a tunable reactance
Open-circuited stub\( -jZ_0\cot\beta l \)capacitive for \( l < \lambda/4 \)
\( l = \lambda/2 \)\( Z_L \)half-wave line repeats the load
\( l = \lambda/4 \)\( Z_0^2/Z_L \)impedance inverter: short \( \to \) open
Matched load\( Z_0 \) for any \( l \)

Quarter-wave transformer. To match a real load \( R_L \) to a line \( Z_0 \), insert a \( \lambda/4 \) section of impedance \( Z_T = \sqrt{Z_0R_L} \). It works exactly at one frequency (and its odd multiples).

Pulses and step response

A source of open-circuit voltage \( V_s \) and internal resistance \( R_s \) launches \( V_s Z_0/(R_s + Z_0) \) onto the line: at the instant of launch the line looks like a resistor \( Z_0 \). The wave then bounces between the ends with reflection coefficients \( \Gamma_L \) and \( \Gamma_s = (R_s - Z_0)/(R_s + Z_0) \); the voltage at any point settles to the DC value after many round trips. Time-domain reflectometry uses the delay of the first reflection to locate faults: distance \( = v\,t/2 \).

Part 2: Waveguides

Why a hollow pipe has no TEM mode

A TEM wave (\( E_z = B_z = 0 \)) inside a guide would need transverse fields satisfying the two-dimensional Laplace equation with the conductor as a single equipotential boundary, which forces the field to vanish. A TEM wave needs two separate conductors (coax, two-wire line). A hollow guide carries only

  • TE modes: \( E_z = 0 \), \( B_z \neq 0 \);
  • TM modes: \( B_z = 0 \), \( E_z \neq 0 \).

Rectangular guide (\( a \times b \), \( a > b \), filled with \( \mu, \varepsilon \))

Write fields as \( f(x, y)e^{j(\omega t - k_zz)} \). The longitudinal component obeys

$$\left[\partial_x^2 + \partial_y^2 + k_c^2\right]f = 0, \qquad k_c^2 = \omega^2\mu\varepsilon - k_z^2$$

Boundary conditions give \( B_z = B_0\cos(m\pi x/a)\cos(n\pi y/b) \) for TE and \( E_z = E_0\sin(m\pi x/a)\sin(n\pi y/b) \) for TM, with

$$k_c^2 = \left(\frac{m\pi}{a}\right)^2 + \left(\frac{n\pi}{b}\right)^2, \qquad \boxed{f_{c,mn} = \frac{v}{2}\sqrt{\left(\frac{m}{a}\right)^2 + \left(\frac{n}{b}\right)^2}}, \quad v = \frac{1}{\sqrt{\mu\varepsilon}}$$
Mode familyAllowed \( (m, n) \)Lowest
TE\( _{mn} \)\( m, n \ge 0 \), not both zeroTE\( _{10} \): \( f_c = v/2a \), \( \lambda_c = 2a \)
TM\( _{mn} \)\( m, n \ge 1 \) (a sine with zero index vanishes)TM\( _{11} \)

TE\( _{10} \) is the dominant mode for \( a > b \). TE\( _{mn} \) and TM\( _{mn} \) with the same indices (both \( \ge 1 \)) share a cut-off: they are degenerate.

Dispersion: the plasma hyperbola again

$$\boxed{\omega^2 = \omega_c^2 + v^2k_z^2}$$

identical in form to the plasma dispersion relation. With \( F = \sqrt{1 - (f_c/f)^2} \):

QuantityFormula
Guide wavelength\( \lambda_g = \lambda/F \) (longer than in free space)
Phase velocity\( v_p = v/F > v \)
Group velocity\( v_g = vF < v \); \( v_pv_g = v^2 \)
TE wave impedance\( Z_{\text{TE}} = \eta/F \) (above \( \eta \))
TM wave impedance\( Z_{\text{TM}} = \eta F \) (below \( \eta \))
Below cut-off\( k_z = -j\alpha \), \( \alpha = \sqrt{\omega_c^2 - \omega^2}/v \): evanescent, no power flow

Useful identity: \( \dfrac{1}{\lambda^2} = \dfrac{1}{\lambda_g^2} + \dfrac{1}{\lambda_c^2} \).

The bouncing-plane-wave picture of TE\( _{10} \)

\( E_y = E_0\sin(\pi x/a)\cos(\omega t - k_zz) \), with \( H_x \) and \( H_z \) completing the mode. Write \( \sin(\pi x/a) \) as the difference of two exponentials: the mode is two plane waves zig-zagging between the side walls at angle \( \theta \) to the axis, with \( \cos\theta = F \). Energy moves along the guide at \( v\cos\theta = v_g \); the crest pattern on the wall sweeps along at \( v/\cos\theta = v_p \). At cut-off \( \theta = 90^\circ \): the waves bounce straight across and nothing advances.

graph TD
    A["Frequency f in guide a × b"] --> B{"f vs f_c,mn
for each mode"} B -->|"f > f_c"| C["Mode propagates
λ_g = λ/√(1 − f_c²/f²)"] B -->|"f < f_c"| D["Mode evanescent
decays as e^(−αz)"] C --> E["Single-mode band:
f_c,10 < f < next cut-off"] C --> F["v_g = v√(1 − f_c²/f²)
v_p v_g = v²"]

Circular guide (radius \( a \))

The transverse dependence is a Bessel function \( J_m(k_c\rho) \). For TM modes \( E_z \) must vanish on the wall, so \( k_ca = x_{mn} \) (zeros of \( J_m \)); for TE modes \( \partial B_z/\partial\rho = 0 \), so \( k_ca = x'_{mn} \) (zeros of \( J_m' \)).

ModeRoot\( \lambda_c \)
TE\( _{11} \) (dominant)\( x'_{11} = 1.841 \)\( 2\pi a/1.841 = 3.41a \)
TM\( _{01} \)\( x_{01} = 2.405 \)\( 2.61a \)

Coaxial line as a waveguide

Coax carries a TEM mode with no cut-off at all, so it works down to DC. Higher TE and TM modes appear once the circumference is comparable to the wavelength; the first (TE\( _{11} \)) has \( \lambda_c \approx \pi(a + b) \), a commonly used approximation. Keeping below that frequency keeps the coax single-mode.

Cavity resonators

Close a rectangular guide with conducting walls at \( z = 0 \) and \( z = d \). Then \( k_z = p\pi/d \) and the allowed frequencies are discrete:

$$\boxed{f_{mnp} = \frac{v}{2}\sqrt{\left(\frac{m}{a}\right)^2 + \left(\frac{n}{b}\right)^2 + \left(\frac{p}{d}\right)^2}}$$

For TE modes \( p \ge 1 \) (the transverse \( E \) must vanish at the end walls); for TM modes \( p \ge 0 \) is allowed. A 10 cm air-filled cube has lowest frequency \( f_{101} = (c/2)\sqrt{2}/0.1 = 2.12 \) GHz. Wall losses give a finite quality factor \( Q = \omega\times\text{(energy stored)}/\text{(power lost)} \); a high-\( Q \) cavity resonates over a bandwidth \( f/Q \). Counting cavity modes below a frequency is the classic route to the Rayleigh–Jeans density of states.

Memory Tricks

Don’t Confuse

ThisvsThat
\( Z_0 \): ratio for one travelling wave\( Z_{\text{in}} \): ratio of total \( V \) and \( I \) at a point
Reflection coefficient \( \Gamma \) (amplitude)Reflected power fraction \( \vert \Gamma\vert ^2 \)
Coax: TEM, no cut-offHollow guide: TE/TM only, cut-off \( f_c \)
Phase velocity \( v_p > c \) in a guideGroup velocity \( v_g < c \), carries energy
Guide wavelength \( \lambda_g > \lambda_0 \)Cut-off wavelength \( \lambda_c = 2a \) (TE\( _{10} \))
Distortionless: \( R/L = G/C \)Lossless: \( R = G = 0 \)

Common Mistakes

Practice

All questions below are original practice questions written for this page. They are not from any CSIR NET paper. Take \( c = 3.0\times10^8 \) m/s and \( \eta_0 = 377 \) Ω.

Level 1: Foundation

  1. Write \( Z_0 \) and the phase velocity of a lossless line.
  2. What is the lowest TM mode of a rectangular guide?
  3. What is the input impedance of a short-circuited \( \lambda/4 \) lossless line?
Answers
  1. \( Z_0 = \sqrt{L/C} \), \( v = 1/\sqrt{LC} \).
  2. TM\( _{11} \).
  3. Infinite (an open circuit): \( Z_0^2/0 \).

Level 2: Part B Style

Practice Q1. A coaxial line has outer-to-inner radius ratio 3.5 and is filled with a dielectric of \( \varepsilon_r = 2.25 \). Its characteristic impedance is about:

(a) 33 Ω (b) 50 Ω (c) 75 Ω (d) 113 Ω

Answer: (b)

\( Z_0 = (60/\sqrt{2.25})\ln3.5 = 40\times1.253 = 50.1 \) Ω. Option (c) forgets \( \sqrt{\varepsilon_r} \); option (d) multiplies by \( \sqrt{\varepsilon_r} \) instead of dividing.

Practice Q2. A 100 Ω resistive load terminates a lossless 50 Ω line. The VSWR and the fraction of incident power reflected are:

(a) 2 and 1/9 (b) 2 and 1/3 (c) 3 and 1/4 (d) 1.5 and 1/9

Answer: (a)

\( \Gamma = (100 - 50)/(100 + 50) = 1/3 \). \( S = (1 + 1/3)/(1 - 1/3) = 2 \). Reflected power \( |\Gamma|^2 = 1/9 \approx 11\% \). Option (b) gives the amplitude ratio as the power ratio.

Practice Q3. A quarter-wave section is to match a 200 Ω resistive load to a 50 Ω line. Its characteristic impedance should be:

(a) 125 Ω (b) 150 Ω (c) 100 Ω (d) 250 Ω

Answer: (c)

\( Z_T = \sqrt{50\times200} = 100 \) Ω. Option (a) is the arithmetic mean.

Practice Q4. An air-filled rectangular guide has \( a = 2.286 \) cm and \( b = 1.016 \) cm. At 10 GHz the propagating modes are:

(a) TE\( _{10} \) only (b) TE\( _{10} \) and TE\( _{01} \) (c) TE\( _{10} \), TE\( _{20} \) and TE\( _{01} \) (d) TE\( _{10} \) and TM\( _{10} \)

Answer: (a)

Cut-offs: TE\( _{10} \) 6.56 GHz, TE\( _{20} \) 13.1 GHz, TE\( _{01} \) 14.8 GHz. Only TE\( _{10} \) is below 10 GHz. TM\( _{10} \) (option d) does not exist.

Level 3: Part C Style

Practice Q5. For the guide of Q4 operating at 10 GHz in the TE\( _{10} \) mode, consider:

  1. The guide wavelength is about 3.97 cm.
  2. The group velocity is about \( 2.26\times10^8 \) m/s.
  3. The wave impedance is about 285 Ω.
  4. Filling the guide with a dielectric of \( \varepsilon_r = 2.25 \) lowers the TE\( _{10} \) cut-off to about 4.37 GHz.

Which are correct?

(a) 1, 2 and 4 only (b) 1 and 2 only (c) 1, 3 and 4 only (d) 2, 3 and 4 only

Answer: (a) 1, 2 and 4 only

\( f_c = 6.56 \) GHz, \( f_c/f = 0.656 \), \( F = \sqrt{1 - 0.430} = 0.755 \).

Statement 1: \( \lambda_g = 3.00/0.755 = 3.97 \) cm. True.

Statement 2: \( v_g = cF = 2.26\times10^8 \) m/s. True.

Statement 3: \( Z_{\text{TE}} = \eta_0/F = 499 \) Ω; 285 Ω is \( \eta_0F \), the TM formula. False.

Statement 4: \( f_c = c/(2a\sqrt{\varepsilon_r}) = 6.56/1.5 = 4.37 \) GHz. True.

Practice Q6. A lossless 50 Ω line is one-eighth of a wavelength long. Consider its input impedance for different terminations:

  1. Short-circuited: \( Z_{\text{in}} = +j50 \) Ω (inductive).
  2. Open-circuited: \( Z_{\text{in}} = -j50 \) Ω (capacitive).
  3. Terminated in 100 Ω: \( Z_{\text{in}} = (40 - j30) \) Ω.
  4. Terminated in 100 Ω: \( |\Gamma| \) at the input is smaller than at the load, because the line has transformed the impedance.

Which are correct?

(a) 1, 2 and 3 only (b) 1 and 2 only (c) 3 and 4 only (d) 1, 2, 3 and 4

Answer: (a) 1, 2 and 3 only

\( \beta l = (2\pi/\lambda)(\lambda/8) = \pi/4 \), \( \tan\beta l = 1 \).

Statement 1: \( jZ_0\tan\beta l = j50 \) Ω. True. Statement 2: \( -jZ_0\cot\beta l = -j50 \) Ω. True.

Statement 3: \( Z_{\text{in}} = 50\dfrac{100 + j50}{50 + j100} = 50\dfrac{(100 + j50)(50 - j100)}{50^2 + 100^2} = 50\dfrac{10000 - j7500}{12500} = 40 - j30 \) Ω. True.

Statement 4: on a lossless line \( |\Gamma| \) is the same everywhere; only its phase rotates. Check: \( \left|\dfrac{40 - j30 - 50}{40 - j30 + 50}\right| = \dfrac{\sqrt{1000}}{\sqrt{9000}} = \dfrac13 \). False.

Practice Q7. A line has \( L = 250 \) nH/m, \( C = 100 \) pF/m and series resistance \( R = 0.05 \) Ω/m. Its shunt conductance \( G \) is chosen to make it distortionless. Consider:

  1. \( Z_0 = 50 \) Ω and the signal speed is \( 2.0\times10^8 \) m/s.
  2. \( G = 2.0\times10^{-5} \) S/m.
  3. The attenuation constant is \( 1.0\times10^{-3} \) Np/m, so after 1 km the power has fallen to about 13.5% (about 8.7 dB loss).
  4. Pulses of different widths travel at different speeds on this line.

Which are correct?

(a) 1 and 2 only (b) 1, 2 and 3 only (c) 2, 3 and 4 only (d) 1 and 4 only

Answer: (b) 1, 2 and 3 only

Statement 1: \( Z_0 = \sqrt{250\times10^{-9}/100\times10^{-12}} = \sqrt{2500} = 50 \) Ω; \( v = 1/\sqrt{2.5\times10^{-17}} = 2.0\times10^8 \) m/s. True.

Statement 2: \( G = RC/L = 0.05\times100\times10^{-12}/250\times10^{-9} = 2.0\times10^{-5} \) S/m. True.

Statement 3: \( \alpha = \sqrt{RG} = \sqrt{10^{-6}} = 10^{-3} \) Np/m. Over 1000 m the voltage falls by \( e^{-1} \) and the power by \( e^{-2} = 0.135 \); \( 10\log_{10}(e^2) = 8.69 \) dB. True.

Statement 4: on a distortionless line \( v \) and \( \alpha \) are independent of frequency, so all Fourier components, and hence all pulse shapes, travel together. False.

Quick Revision Table

QuantityFormula
Propagation constant\( \gamma = \sqrt{(R + j\omega L)(G + j\omega C)} \)
Characteristic impedance\( Z_0 = \sqrt{(R + j\omega L)/(G + j\omega C)} \); lossless \( \sqrt{L/C} \)
Distortionless\( R/L = G/C \); \( \alpha = \sqrt{RG} \)
Coax / two-wire\( (60/\sqrt{\varepsilon_r})\ln(b/a) \); \( (120/\sqrt{\varepsilon_r})\cosh^{-1}(d/2a) \)
Reflection\( \Gamma = (Z_L - Z_0)/(Z_L + Z_0) \)
VSWR\( S = (1 + \vert \Gamma\vert )/(1 - \vert \Gamma\vert ) \)
Input impedance\( Z_0(Z_L + jZ_0\tan\beta l)/(Z_0 + jZ_L\tan\beta l) \)
Quarter-wave\( Z_{\text{in}} = Z_0^2/Z_L \); matching \( Z_T = \sqrt{Z_0R_L} \)
Rectangular cut-off\( f_{c,mn} = (v/2)\sqrt{(m/a)^2 + (n/b)^2} \); TE\( _{10} \): \( v/2a \)
Guide relations\( \lambda_g = \lambda/F \), \( v_g = vF \), \( v_p = v/F \), \( F = \sqrt{1 - f_c^2/f^2} \)
Wave impedance\( Z_{\text{TE}} = \eta/F \), \( Z_{\text{TM}} = \eta F \)
CircularTE\( _{11} \) \( \lambda_c = 3.41a \); TM\( _{01} \) \( \lambda_c = 2.61a \)
Cavity\( f_{mnp} = (v/2)\sqrt{(m/a)^2 + (n/b)^2 + (p/d)^2} \)

Key Takeaways

What’s Next