Skip to content

Magnetostatics and Electromagnetic Induction

CSIR NET magnetostatics and induction: Biot–Savart, Ampère's law, vector potential, magnetic dipoles, Faraday's law, inductance, energy, practice.

  • 20 min read
  • Updated
On this page · 17 sections
  1. Prerequisites
  2. The Hook: A Magnet That Falls Slowly
  3. The Lorentz Force
  4. The Biot–Savart Law
  5. Ampère’s Law and the Divergence of B
  6. The Magnetic Vector Potential
  7. Magnetic Dipoles
  8. Boundary Conditions and Magnetised Matter
  9. Faraday’s Law of Induction
  10. Inductance
  11. Memory Tricks
  12. Don’t Confuse
  13. Common Mistakes
  14. Practice
  15. Quick Revision Table
  16. Key Takeaways
  17. What’s Next

Prerequisites

The Hook: A Magnet That Falls Slowly

The Lorentz Force

A charge \( q \) moving with velocity \( \mathbf v \) feels

$$\mathbf F = q(\mathbf E + \mathbf v\times\mathbf B)$$

The magnetic part is perpendicular to \( \mathbf v \), so magnetic forces do no work. They change the direction of motion, never the speed. (When a magnetic crane lifts a car, the work is done by the electric forces in the wires; the magnetic force redirects it.) The full consequences for single particles are on Charged Particles in Static Uniform Fields.

On a current element: \( d\mathbf F = I\,d\mathbf l\times\mathbf B \). Two long parallel wires carrying \( I_1 \), \( I_2 \) a distance \( d \) apart feel a force per unit length

$$\frac{F}{l} = \frac{\mu_0I_1I_2}{2\pi d}$$

attractive for parallel currents, repulsive for antiparallel: the opposite of like charges. \( \mu_0 = 4\pi\times10^{-7} \) N A\( ^{-2} \) to the precision the exam needs.

The Biot–Savart Law

For a steady current,

$$\boxed{\mathbf B(\mathbf r) = \frac{\mu_0}{4\pi}\int\frac{I\,d\mathbf l'\times\hat{\boldsymbol{\mathscr R}}}{\mathscr R^2} = \frac{\mu_0}{4\pi}\int\frac{\mathbf J(\mathbf r')\times\hat{\boldsymbol{\mathscr R}}}{\mathscr R^2}d\tau'}$$

Standard results

SourceFieldWhere
Straight segment, perpendicular distance \( s \)\( \dfrac{\mu_0I}{4\pi s}(\sin\theta_2 - \sin\theta_1) \)\( \theta \) measured from the perpendicular to each end
Infinite straight wire\( \dfrac{\mu_0I}{2\pi s} \)circles around the wire
Semi-infinite wire, point beside its end\( \dfrac{\mu_0I}{4\pi s} \)half the infinite value
Circular loop, centre\( \dfrac{\mu_0I}{2R} \)along the axis
Circular loop, on axis\( \dfrac{\mu_0IR^2}{2(R^2 + z^2)^{3/2}} \)along the axis
Arc of angle \( \phi \), centre\( \dfrac{\mu_0I\phi}{4\pi R} \)straight segments pointing at the centre add nothing
Square loop of side \( a \), centre\( \dfrac{2\sqrt2\,\mu_0I}{\pi a} \)four segments, each \( \theta = \pm45^\circ \)
Regular \( n \)-gon, circumradius \( R \), centre\( \dfrac{n\mu_0I}{2\pi R}\tan\dfrac{\pi}{n} \)tends to \( \mu_0I/2R \) as \( n \to \infty \)

Helmholtz coils. Two coaxial coils of radius \( R \) and \( N \) turns each, separated by \( R \) and carrying the same current in the same sense, give a field at the midpoint whose first, second and third derivatives along the axis vanish:

$$B_{\text{mid}} = \left(\frac{4}{5}\right)^{3/2}\frac{\mu_0NI}{R} \approx 0.716\frac{\mu_0NI}{R}$$

Ampère’s Law and the Divergence of B

The Biot–Savart field satisfies

$$\boxed{\nabla\cdot\mathbf B = 0, \qquad \nabla\times\mathbf B = \mu_0\mathbf J \quad\Longleftrightarrow\quad \oint\mathbf B\cdot d\mathbf l = \mu_0I_{\text{enc}}}$$

\( \nabla\cdot\mathbf B = 0 \) says there are no magnetic monopoles: field lines close on themselves. Ampère’s law, like Gauss’s law, finds \( \mathbf B \) only with symmetry: infinite lines, infinite planes, solenoids and toroids.

ConfigurationField
Inside a long straight wire of radius \( a \), uniform current\( \dfrac{\mu_0Is}{2\pi a^2} \)
Outside it\( \dfrac{\mu_0I}{2\pi s} \)
Infinite sheet, surface current \( K \)\( \dfrac{\mu_0K}{2} \), parallel to the sheet and perpendicular to \( \mathbf K \)
Long solenoid, \( n \) turns per length\( \mu_0nI \) inside, 0 outside
Toroid, \( N \) turns\( \dfrac{\mu_0NI}{2\pi s} \) inside the windings, 0 elsewhere
Coaxial cable, inner \( a \), outer \( b \) (equal and opposite currents)\( \dfrac{\mu_0I}{2\pi s} \) for \( a < s < b \), 0 outside

The Magnetic Vector Potential

Since \( \nabla\cdot\mathbf B = 0 \), write \( \mathbf B = \nabla\times\mathbf A \). \( \mathbf A \) is not unique: adding any gradient leaves \( \mathbf B \) unchanged. Choosing the Coulomb gauge \( \nabla\cdot\mathbf A = 0 \), Ampère’s law becomes three Poisson equations,

$$\nabla^2\mathbf A = -\mu_0\mathbf J, \qquad \mathbf A(\mathbf r) = \frac{\mu_0}{4\pi}\int\frac{\mathbf J(\mathbf r')}{\mathscr R}d\tau'$$

so \( \mathbf A \) tends to point along the current.

FieldA convenient vector potential
Uniform \( \mathbf B \)\( \mathbf A = \tfrac{1}{2}\mathbf B\times\mathbf r \) (symmetric gauge), or \( \mathbf A = Bx\,\hat y \) (Landau gauge, for \( \mathbf B = B\hat z \))
Inside a long solenoid of radius \( R \)\( A_\phi = \tfrac{1}{2}\mu_0nIs \)
Outside it\( A_\phi = \dfrac{\mu_0nIR^2}{2s} \), non-zero although \( \mathbf B = 0 \)
Infinite wire\( \mathbf A = -\dfrac{\mu_0I}{2\pi}\ln(s/s_0)\,\hat z \)

The non-zero \( \mathbf A \) outside a solenoid is the basis of the Aharonov–Bohm effect: electrons passing on either side pick up a relative phase \( q\Phi/\hbar \) though they never meet a field. The flux through any loop is \( \Phi = \oint\mathbf A\cdot d\mathbf l \).

Magnetic Dipoles

Far from any small current loop the leading term is the dipole term, with magnetic moment \( \mathbf m = I\mathbf a \) (\( \mathbf a \) the vector area, right-hand rule with the current):

$$\mathbf A_{\text{dip}} = \frac{\mu_0}{4\pi}\frac{\mathbf m\times\hat r}{r^2}, \qquad \boxed{\mathbf B_{\text{dip}} = \frac{\mu_0}{4\pi r^3}\left[3(\mathbf m\cdot\hat r)\hat r - \mathbf m\right]}$$

There is no monopole term: \( \oint d\mathbf l = 0 \). In an external field:

QuantityFormula
Torque\( \mathbf N = \mathbf m\times\mathbf B \)
Energy\( U = -\mathbf m\cdot\mathbf B \)
Force\( \mathbf F = \nabla(\mathbf m\cdot\mathbf B) \); zero in a uniform field
Orbiting charge\( \mathbf m = \dfrac{q}{2m_q}\mathbf L \), the classical gyromagnetic ratio

A charge \( q \) on a circular orbit of radius \( r \) at speed \( v \) is a current \( qv/2\pi r \), so \( m = qvr/2 \), which is \( (q/2m_q)L \). For the electron the spin moment has twice this ratio (\( g \approx 2 \)), a quantum result.

Boundary Conditions and Magnetised Matter

Across a surface carrying surface current \( \mathbf K \), with \( \hat n \) from region 1 to region 2:

$$B_{2\perp} = B_{1\perp}, \qquad \mathbf B_2 - \mathbf B_1 = \mu_0\mathbf K\times\hat n, \qquad \mathbf A_2 = \mathbf A_1$$

The normal component is continuous; the tangential component jumps by \( \mu_0K \).

Matter responds with a magnetisation \( \mathbf M \) (moment per volume). Its field is that of bound currents:

$$\mathbf J_b = \nabla\times\mathbf M, \qquad \mathbf K_b = \mathbf M\times\hat n$$

Defining \( \mathbf H = \mathbf B/\mu_0 - \mathbf M \) leaves only free current as a source: \( \nabla\times\mathbf H = \mathbf J_f \), \( \oint\mathbf H\cdot d\mathbf l = I_{f,\text{enc}} \). In linear media \( \mathbf M = \chi_m\mathbf H \) and \( \mathbf B = \mu\mathbf H \) with \( \mu = \mu_0(1 + \chi_m) \).

Class\( \chi_m \)Origin
Diamagneticsmall, negativeinduced orbital moments oppose the field (Lenz at the atomic scale)
Paramagneticsmall, positivealignment of permanent moments; \( \chi \propto 1/T \) (Curie law)
Ferromagneticlarge, field-dependent, hystereticexchange-coupled domains; paramagnetic above the Curie temperature
Superconductor (Meissner state)\( -1 \)perfect diamagnet, \( \mathbf B = 0 \) inside

A uniformly magnetised sphere has bound surface current \( K_b = M\sin\theta \) and a uniform interior field \( \mathbf B = \frac{2}{3}\mu_0\mathbf M \); outside it is a perfect dipole with \( \mathbf m = \frac{4}{3}\pi R^3\mathbf M \). Compare the uniformly polarised sphere, whose interior field is \( -\mathbf P/3\varepsilon_0 \).

Faraday’s Law of Induction

Any change of magnetic flux through a circuit induces an emf

$$\boxed{\mathcal E = -\frac{d\Phi}{dt}, \qquad \nabla\times\mathbf E = -\frac{\partial\mathbf B}{\partial t}}$$

The minus sign is Lenz’s law: the induced current flows so as to oppose the change in flux. For an \( N \)-turn coil, \( \mathcal E = -N\,d\Phi/dt \).

The flux rule covers two physically different cases with one formula:

  1. Motional emf. A conductor moves through a static field; the emf is the magnetic force per unit charge, \( \mathcal E = \oint(\mathbf v\times\mathbf B)\cdot d\mathbf l \). A rod of length \( l \) moving at \( v \) perpendicular to \( B \): \( \mathcal E = Blv \).
  2. Transformer emf. A stationary loop in a changing field; the emf comes from a genuinely new, non-conservative electric field with \( \nabla\times\mathbf E \neq 0 \).

Motional emf results

Setupemf
Rod on rails, speed \( v \)\( Blv \)
Rod of length \( l \) rotating about one end at \( \omega \), \( \mathbf B \) along the axis\( \tfrac{1}{2}B\omega l^2 \)
Faraday disc of radius \( R \)\( \tfrac{1}{2}B\omega R^2 \) between axle and rim
\( N \)-turn coil of area \( A \) rotating at \( \omega \) in uniform \( B \)\( NBA\omega\sin\omega t \)

The induced electric field

Where \( \partial\mathbf B/\partial t \) has symmetry, find \( \mathbf E \) the way Ampère’s law finds \( \mathbf B \): \( \oint\mathbf E\cdot d\mathbf l = -d\Phi/dt \). For a long solenoid of radius \( R \) with uniform \( dB/dt \):

$$E_\phi = \begin{cases}\dfrac{s}{2}\dfrac{dB}{dt}, & s < R\\[2mm] \dfrac{R^2}{2s}\dfrac{dB}{dt}, & s > R\end{cases}$$

The field outside is non-zero though \( \mathbf B = 0 \) there. It is largest at \( s = R \), and it has the same value at \( s = R/2 \) as at \( s = 2R \).

Conducting rod on rails: terminal velocity

A rod of length \( l \), mass \( m \), slides on frictionless rails joined by a resistor \( R \), in a field \( B \) perpendicular to the plane, pulled by a constant force \( F \). The current is \( I = Blv/R \) and the retarding force \( IlB = B^2l^2v/R \). Newton’s law:

$$m\frac{dv}{dt} = F - \frac{B^2l^2}{R}v \quad\Rightarrow\quad v(t) = v_t\left(1 - e^{-t/\tau}\right), \quad v_t = \frac{FR}{B^2l^2}, \quad \tau = \frac{mR}{B^2l^2}$$

At terminal speed, the mechanical power \( Fv_t \) equals the Joule heating \( I^2R \). The falling magnet in a pipe is the same physics with a distributed resistor.

Inductance

The flux through circuit 2 due to current \( I_1 \) in circuit 1 is \( \Phi_2 = M_{21}I_1 \). The Neumann formula

$$M = \frac{\mu_0}{4\pi}\oint\oint\frac{d\mathbf l_1\cdot d\mathbf l_2}{\mathscr R}$$

is symmetric, so \( M_{12} = M_{21} \): the flux through 2 per unit current in 1 equals the flux through 1 per unit current in 2. Use whichever is easier to compute. The coupling obeys \( M \leq \sqrt{L_1L_2} \).

A circuit’s flux through itself defines the self-inductance, \( \Phi = LI \), with back-emf \( \mathcal E = -L\,dI/dt \).

SystemInductance
Long solenoid, \( N \) turns, length \( l \), area \( A \)\( L = \mu_0N^2A/l = \mu_0n^2Al \)
Toroid of rectangular cross-section, height \( h \), radii \( a, b \)\( L = \dfrac{\mu_0N^2h}{2\pi}\ln\dfrac{b}{a} \)
Coaxial cable, per unit length (surface currents)\( L' = \dfrac{\mu_0}{2\pi}\ln\dfrac{b}{a} \)
Small loop (radius \( b \)) at the centre of a large coaxial loop (radius \( a \gg b \))\( M = \dfrac{\mu_0\pi b^2}{2a} \)
Two solenoids wound on the same core, full coupling\( M = \sqrt{L_1L_2} \)

Inductance scales as \( N^2 \): doubling the turns on the same former quadruples \( L \).

Magnetic energy

The work done against the back-emf in building up a current \( I \) is

$$\boxed{W = \frac{1}{2}LI^2 = \frac{1}{2\mu_0}\int_{\text{all space}}B^2\,d\tau = \frac{1}{2}\oint\mathbf A\cdot\mathbf I\,dl}$$

so the energy density is \( u_B = B^2/2\mu_0 \). This is often the quickest route to \( L \): compute the field energy and set it equal to \( \frac{1}{2}LI^2 \). For two coupled circuits, \( W = \frac{1}{2}L_1I_1^2 + \frac{1}{2}L_2I_2^2 + MI_1I_2 \).

Circuits

CircuitBehaviour
RL, switched on with emf \( \mathcal E_0 \)\( I = \dfrac{\mathcal E_0}{R}\left(1 - e^{-Rt/L}\right) \), time constant \( L/R \)
RL, source removed\( I = I_0e^{-Rt/L} \); energy \( \frac{1}{2}LI_0^2 \) ends as heat in \( R \)
LCoscillates at \( \omega_0 = 1/\sqrt{LC} \); energy swaps between \( \frac{1}{2}CV^2 \) and \( \frac{1}{2}LI^2 \)
Series LCRdamped at rate \( R/2L \); quality factor \( Q = \omega_0L/R \)

Memory Tricks

Don’t Confuse

ThisvsThat
\( \nabla\cdot\mathbf B = 0 \) always\( \nabla\times\mathbf B = \mu_0\mathbf J \) only for steady currents
\( B_\perp \) continuous across a current sheet\( B_\parallel \) jumps by \( \mu_0K \)
\( \mathbf H \) sourced by free current\( \mathbf B \) sourced by all current
Motional emf: \( \mathbf v\times\mathbf B \) forceTransformer emf: induced \( \mathbf E \) with non-zero curl
Self-inductance \( \propto N^2 \)Field of a solenoid \( \propto N \)
\( \mathbf A \) can be non-zero where \( \mathbf B = 0 \)\( \mathbf B = 0 \) does not imply zero flux through a loop enclosing a solenoid
Magnetic force does no workElectric force does work

Common Mistakes

Practice

All questions below are original practice questions written for this page. They are not from any CSIR NET paper.

Level 1: Foundation

  1. Write the magnetic field at the centre of a circular loop of radius \( R \) carrying current \( I \).
  2. A rod of length \( l \) moves with speed \( v \) perpendicular to a uniform field \( B \) and to its own length. What emf appears across it?
  3. The number of turns of a solenoid is tripled, keeping its length and area. By what factor does its self-inductance change?
Answers
  1. \( \mu_0I/2R \), along the axis by the right-hand rule.
  2. \( Blv \).
  3. Nine. \( L = \mu_0N^2A/l \propto N^2 \).

Level 2: Part B Style

Practice Q1. A square loop of side 10 cm carries a current of 2 A. The magnetic field at its centre is closest to:

(a) 8.0 μT (b) 12.6 μT (c) 22.6 μT (d) 25.1 μT

Answer: (c) 22.6 μT

Each side is at \( s = a/2 = 5 \) cm and subtends \( \theta = \pm45^\circ \): \( B_{\text{side}} = \dfrac{\mu_0I}{4\pi(a/2)}(2\sin45^\circ) \). Four sides: \( B = \dfrac{2\sqrt2\mu_0I}{\pi a} = \dfrac{2\sqrt2\times4\pi\times10^{-7}\times2}{\pi\times0.1} = 2.26\times10^{-5} \) T.

Option (a) is \( \mu_0I/\pi a \), forgetting the \( 2\sqrt2 \). Option (d) is \( \mu_0I/2R \) for the inscribed circle of radius \( a/2 \); the square’s corners lie farther out, so its field is a little smaller.

Practice Q2. A solenoid 50 cm long with 2000 turns per metre has a cross-sectional area of 4 cm\( ^2 \). Its self-inductance is approximately:

(a) 0.25 mH (b) 0.50 mH (c) 1.0 mH (d) 2.0 mH

Answer: (c) 1.0 mH

\( L = \mu_0n^2Al = 4\pi\times10^{-7}\times(2000)^2\times4\times10^{-4}\times0.5 = 1.005\times10^{-3} \) H.

Practice Q3. A long solenoid of radius 2 cm has a uniform axial field increasing at 0.5 T s\( ^{-1} \). The magnitudes of the induced electric field at 1 cm and at 4 cm from the axis are, respectively:

(a) 2.5 mV/m and 2.5 mV/m (b) 2.5 mV/m and 0 (c) 5.0 mV/m and 1.25 mV/m (d) 2.5 mV/m and 10 mV/m

Answer: (a) 2.5 mV/m at both

Inside: \( E = \frac{s}{2}\frac{dB}{dt} = \frac{0.01}{2}\times0.5 = 2.5\times10^{-3} \) V/m.

Outside: \( E = \frac{R^2}{2s}\frac{dB}{dt} = \frac{(0.02)^2}{2\times0.04}\times0.5 = 2.5\times10^{-3} \) V/m.

The points \( s = R/2 \) and \( s = 2R \) give equal fields. Option (b) is the common error of setting the field to zero where \( \mathbf B = 0 \).

Practice Q4. A rod slides on horizontal frictionless rails 0.5 m apart, joined by a 2 Ω resistor, in a vertical field of 0.4 T. A constant horizontal force of 0.2 N pulls the rod. Its terminal speed is:

(a) 2.5 m/s (b) 5 m/s (c) 10 m/s (d) 20 m/s

Answer: (c) 10 m/s

\( v_t = \dfrac{FR}{B^2l^2} = \dfrac{0.2\times2}{(0.4)^2(0.5)^2} = \dfrac{0.4}{0.04} = 10 \) m/s. Check: \( I = Blv/R = 0.4\times0.5\times10/2 = 1 \) A; \( I^2R = 2 \) W \( = Fv_t \).

Level 3: Part C Style

Practice Q5. A coaxial cable has an inner conductor of radius \( a \) and a thin outer conductor of radius \( b = e^2a \), carrying equal and opposite currents \( I \) on their surfaces. Consider:

  1. The field between the conductors is \( \mu_0I/2\pi s \) and the field outside is zero.
  2. The inductance per unit length is \( 4\times10^{-7} \) H m\( ^{-1} \).
  3. The magnetic energy per unit length at \( I = 10 \) A is \( 4\times10^{-5} \) J m\( ^{-1} \).
  4. If the inner current were spread uniformly through the inner conductor instead, the inductance per unit length would decrease.

Which are correct?

(a) 1 and 2 only (b) 1, 2 and 3 only (c) 1, 2 and 4 only (d) 2 and 3 only

Answer: (a) 1 and 2 only

Statement 1: Ampère’s law with enclosed current \( I \) between the conductors and \( 0 \) outside. True.

Statement 2: \( L' = \dfrac{\mu_0}{2\pi}\ln\dfrac{b}{a} = 2\times10^{-7}\times2 = 4\times10^{-7} \) H/m. True.

Statement 3: \( W' = \tfrac{1}{2}L'I^2 = \tfrac{1}{2}\times4\times10^{-7}\times100 = 2\times10^{-5} \) J/m. The stated value forgets the \( \tfrac{1}{2} \). False.

Statement 4: a volume current adds field (and energy) inside the inner conductor, \( \mu_0I/8\pi \) per unit length extra in \( L' \). Inductance increases. False.

Practice Q6. A 100-turn coil of area 0.01 m\( ^2 \) rotates at 50 revolutions per second about an axis perpendicular to a uniform field of 0.2 T. The coil is connected to a load. A student records the emf on an oscilloscope. Which statements are correct?

  1. The peak emf is about 62.8 V.
  2. The rms emf is about 44.4 V.
  3. The emf is maximum when the plane of the coil is perpendicular to the field.
  4. Doubling the rotation rate doubles both the peak emf and its frequency.

(a) 1 and 2 only (b) 1, 2 and 4 only (c) 1, 3 and 4 only (d) 2, 3 and 4 only

Answer: (b) 1, 2 and 4 only

\( \omega = 2\pi\times50 = 314.2 \) rad/s. Peak \( = NBA\omega = 100\times0.2\times0.01\times314.2 = 62.8 \) V. True.

rms \( = 62.8/\sqrt2 = 44.4 \) V. True.

\( \Phi = NBA\cos\omega t \), so \( \mathcal E = NBA\omega\sin\omega t \) is largest when \( \Phi = 0 \), that is, when the coil’s plane is parallel to the field (the sides cut the field lines fastest). Statement 3 false.

\( \mathcal E_0 \propto \omega \) and the frequency is \( \omega/2\pi \). True.

Practice Q7. A small circular loop of radius \( b \) lies at the centre of, and coplanar with, a large circular loop of radius \( a \gg b \). The current in the large loop is \( I(t) = I_0\sin\omega t \). The amplitude of the emf induced in the small loop is:

(a) \( \dfrac{\mu_0\pi b^2\omega I_0}{2a} \) (b) \( \dfrac{\mu_0\pi a^2\omega I_0}{2b} \) (c) \( \dfrac{\mu_0b\omega I_0}{2} \) (d) \( \dfrac{\mu_0\pi b^2\omega I_0}{4a} \)

Answer: (a)

The large loop’s field at its centre is \( \mu_0I/2a \), nearly uniform over the small loop. Flux \( = \dfrac{\mu_0I}{2a}\pi b^2 \), so \( M = \dfrac{\mu_0\pi b^2}{2a} \) and the emf amplitude is \( M\omega I_0 \).

By reciprocity the same \( M \) gives the flux through the big loop due to the small loop’s dipole field, a much harder integral. Option (b) swaps the roles of \( a \) and \( b \); a dimensional check alone does not catch it, but the limit \( b \to 0 \) (emf must vanish) does.

Quick Revision Table

ResultFormula
Biot–Savart\( \mathbf B = \frac{\mu_0}{4\pi}\int\frac{I\,d\mathbf l\times\hat{\mathscr R}}{\mathscr R^2} \)
Wire / loop centre / loop axis\( \frac{\mu_0I}{2\pi s} \) / \( \frac{\mu_0I}{2R} \) / \( \frac{\mu_0IR^2}{2(R^2 + z^2)^{3/2}} \)
Square loop centre\( 2\sqrt2\mu_0I/\pi a \)
Ampère\( \oint\mathbf B\cdot d\mathbf l = \mu_0I_{\text{enc}} \)
Solenoid / toroid / sheet\( \mu_0nI \) / \( \mu_0NI/2\pi s \) / \( \mu_0K/2 \)
Dipole\( \mathbf m = I\mathbf a \); \( \mathbf N = \mathbf m\times\mathbf B \); \( U = -\mathbf m\cdot\mathbf B \)
Boundary\( B_\perp \) continuous; \( B_\parallel \) jumps by \( \mu_0K \)
Faraday\( \mathcal E = -d\Phi/dt \); \( \nabla\times\mathbf E = -\partial\mathbf B/\partial t \)
Motional\( Blv \); rotating rod \( \frac{1}{2}B\omega l^2 \)
Solenoid \( L \)\( \mu_0n^2Al \)
Coax \( L' \)\( \frac{\mu_0}{2\pi}\ln(b/a) \)
Energy\( \frac{1}{2}LI^2 = \int\frac{B^2}{2\mu_0}d\tau \)
Terminal velocity\( FR/B^2l^2 \)

Key Takeaways

What’s Next