Skip to content

High-Frequency Devices: Generators, Lines and Detectors

CSIR NET Physical Sciences: transmission lines, VSWR, waveguides, klystron, magnetron, TWT, Gunn, IMPATT, tunnel, PIN and Schottky diodes, RF detectors.

  • 18 min read
  • Updated
On this page · 14 sections
  1. Prerequisites
  2. The Hook: When Wires Stop Being Wires
  3. Components at High Frequency
  4. Transmission Lines
  5. Waveguides and Cavities
  6. High-Frequency Generators
  7. Control and Detection Devices
  8. Memory Tricks
  9. Don’t Confuse
  10. Common Mistakes
  11. Practice
  12. Quick Revision Table
  13. Key Takeaways
  14. What’s Next

Prerequisites

The Hook: When Wires Stop Being Wires

Components at High Frequency

Every real component carries parasitics. A capacitor has lead and plate inductance \( L_s \), so above its self-resonant frequency \( f_{SR} = 1/2\pi\sqrt{L_sC} \) it behaves as an inductor (10 nH with 100 pF resonates at 159 MHz). A resistor has shunt capacitance and lead inductance; an inductor has inter-turn capacitance. Conductors suffer the skin effect: current crowds into a surface layer of depth

$$\delta = \sqrt{\frac{2\rho}{\omega\mu}}$$

(about 2 µm for copper at 1 GHz and 0.65 µm at 10 GHz), so resistance rises as \( \sqrt f \). Surfaces of microwave parts are therefore silver- or gold-plated and polished.

Transistors are limited by charge-storage and transit times. The unity current-gain frequency of a bipolar transistor is

$$f_T = \frac{g_m}{2\pi(C_\pi + C_\mu)}$$

and in a common-emitter stage the base–collector capacitance appears at the input multiplied by the voltage gain (Miller effect, \( C_{\text{in}} \approx C_\mu(1 + \lvert A_v\rvert) \)), which collapses the bandwidth. High-frequency transistor technologies shorten transit paths and use high-mobility materials:

DeviceIdeaTypical use
HBT (heterojunction bipolar)wide-gap emitter blocks hole injection, allowing a heavily doped thin basepower amplifiers, high-speed circuits
MESFETGaAs channel with a Schottky (metal–semiconductor) gate; electron mobility much higher than in Simicrowave amplifiers, oscillators
HEMTelectrons in a two-dimensional gas at a heterojunction (e.g. AlGaAs/GaAs), spatially separated from their donors, so ionised-impurity scattering is smalllowest-noise microwave amplifiers (satellite and radio-astronomy receivers)

Transmission Lines

A line with inductance \( L \) and capacitance \( C \) per unit length (lossless) carries waves with

$$\boxed{Z_0 = \sqrt{\frac{L}{C}}, \qquad v = \frac{1}{\sqrt{LC}} = \frac{c}{\sqrt{\varepsilon_r}}}$$

\( Z_0 \) is the ratio of voltage to current in a single travelling wave. For coaxial cable, \( Z_0 = \dfrac{60}{\sqrt{\varepsilon_r}}\ln\dfrac{b}{a} \) Ω; common standards are 50 Ω and 75 Ω.

Reflection and standing waves

A load \( Z_L \) on a line of impedance \( Z_0 \) reflects a fraction of the incident voltage wave:

$$\boxed{\Gamma = \frac{Z_L - Z_0}{Z_L + Z_0}, \qquad \text{VSWR} = \frac{V_{\max}}{V_{\min}} = \frac{1 + \lvert\Gamma\rvert}{1 - \lvert\Gamma\rvert}}$$
  • Matched load \( Z_L = Z_0 \): \( \Gamma = 0 \), VSWR = 1, no standing wave.
  • Short circuit: \( \Gamma = -1 \); open circuit: \( \Gamma = +1 \); both VSWR = \( \infty \).
  • Reflected power fraction \( \lvert\Gamma\rvert^2 \); return loss \( = -20\log_{10}\lvert\Gamma\rvert \) dB.
  • Standing-wave maxima and minima are \( \lambda/4 \) apart; adjacent minima \( \lambda/2 \) apart. For a resistive load, a voltage minimum sits at the load if \( Z_L < Z_0 \) and a maximum if \( Z_L > Z_0 \).

Input impedance and the quarter-wave transformer

A lossless line of length \( l \) terminated in \( Z_L \) presents

$$Z_{\text{in}} = Z_0\frac{Z_L + jZ_0\tan\beta l}{Z_0 + jZ_L\tan\beta l}, \qquad \beta = \frac{2\pi}{\lambda}$$

Special lengths:

Length\( Z_{\text{in}} \)Use
\( \lambda/2 \)\( Z_L \) (repeats)
\( \lambda/4 \)\( Z_0^2/Z_L \) (inverts)quarter-wave transformer: match \( Z_1 \) to \( Z_2 \) with \( Z_0 = \sqrt{Z_1Z_2} \)
shorted stub, \( l < \lambda/4 \)\( jZ_0\tan\beta l \) (inductive)matching stubs, tuning
open stub, \( l < \lambda/4 \)\( -jZ_0\cot\beta l \) (capacitive)
shorted \( \lambda/4 \)\( \infty \)insulating support, filters

Matching 50 Ω to 100 Ω needs a quarter-wave section of \( \sqrt{5000} = 70.7 \) Ω. The match is perfect only at the design frequency.

Waveguides and Cavities

A hollow metal pipe carries electromagnetic waves only above a cut-off frequency, in TE and TM modes (no TEM mode in a single hollow conductor). For a rectangular guide with inner dimensions \( a > b \):

$$\boxed{f_{c,mn} = \frac{c}{2}\sqrt{\left(\frac{m}{a}\right)^2 + \left(\frac{n}{b}\right)^2}}$$

TE modes need \( m \) or \( n \) non-zero; TM modes need both non-zero (lowest TM\( _{11} \)). The dominant mode is TE\( _{10} \) with \( f_c = c/2a \) (cut-off wavelength \( 2a \)). Guides are used in the single-mode band between TE\( _{10} \) and the next mode.

Above cut-off,

$$\lambda_g = \frac{\lambda_0}{\sqrt{1 - (f_c/f)^2}}, \qquad v_p = \frac{c}{\sqrt{1 - (f_c/f)^2}} > c, \qquad v_g = c\sqrt{1 - (f_c/f)^2} < c, \qquad v_pv_g = c^2$$

The phase velocity exceeds \( c \) but carries no information; energy travels at \( v_g \). Below cut-off the fields decay exponentially (evanescent modes), which is used in attenuators.

A cavity resonator is a closed section of guide; its resonances are standing-wave modes with very high quality factor \( Q = f_0/\Delta f \) (thousands or more for metal cavities). Cavities set the frequency of klystrons and many microwave oscillators and are used as wavemeters and filters.

Passive microwave components: directional couplers (sample forward or reflected power), attenuators, isolators and circulators (non-reciprocal ferrite devices that pass power one way, protecting sources from reflections), magic tees, hybrids and matched terminations.

High-Frequency Generators

Oscillators up to hundreds of megahertz

LC oscillators satisfy Barkhausen with a resonant tank: Colpitts (capacitive divider, \( f = 1/2\pi\sqrt{LC_1C_2/(C_1 + C_2)} \)), Hartley (tapped inductor, \( f = 1/2\pi\sqrt{(L_1 + L_2 + 2M)C} \)). Crystal oscillators replace the tank by a quartz resonator, whose piezoelectric resonance has a very high \( Q \) and hence excellent frequency stability. Frequency synthesisers lock a tunable oscillator to a crystal reference with a phase-locked loop.

Vacuum-tube microwave sources

Ordinary tubes fail at microwave frequencies because the electron transit time between electrodes becomes comparable to the period. Microwave tubes turn transit time into the mechanism.

Klystron. An electron beam passes the gap of a buncher cavity whose RF field speeds some electrons up and slows others: velocity modulation. In the drift space the fast electrons catch up with the slow ones, so the beam becomes density-modulated (bunched). The bunched beam passes a catcher cavity and gives up energy to its field. Two-cavity and multi-cavity klystrons are narrow-band, high-gain, high-power amplifiers.

Reflex klystron. One cavity and a negative repeller electrode that turns the beam back through the same cavity. It oscillates when bunches return at the right phase: transit time in the repeller space \( T = (n + \tfrac{3}{4})/f \), \( n = 0, 1, 2, \ldots \). Low power; tuned mechanically (cavity) and electronically (repeller voltage), long used as a laboratory signal source and local oscillator.

Magnetron. A crossed-field device: a cylindrical cathode inside an anode block containing resonant cavities, with a radial electric field and an axial magnetic field. Electrons spiral, form rotating “spokes” of charge that interact with the cavity fields, and deliver high power at good efficiency. It is a high-power oscillator: radar transmitters and domestic microwave ovens (2.45 GHz).

Travelling-wave tube (TWT). A slow-wave structure (usually a helix) reduces the axial phase velocity of the RF wave to about the beam velocity, so beam and wave interact continuously along the tube rather than at one gap. With no resonant cavity, it is a broadband amplifier (bandwidths up to an octave), the workhorse of satellite transponders. The backward-wave oscillator uses interaction with a backward space harmonic and is voltage-tunable over a wide range.

Solid-state microwave sources

These are two-terminal devices with negative differential resistance (NDR): placed in a resonant circuit, they cancel its loss and sustain oscillation.

Gunn diode (transferred-electron device). In n-type GaAs (and InP) the conduction band has a low-mass, high-mobility central valley and higher-energy satellite valleys with heavier effective mass and lower mobility. Above a threshold field (a few kV/cm in GaAs) electrons gain enough energy to transfer to the satellite valleys, so their average drift velocity falls as the field rises: bulk NDR. The sample becomes unstable and high-field domains form near the cathode and drift to the anode at about the saturated velocity. In the transit-time mode the frequency is

$$\boxed{f \approx \frac{v_d}{L}}$$

With \( v_d \approx 10^5 \) m/s, a 10 µm active length gives about 10 GHz. Note that the Gunn effect is a bulk property: there is no junction. Gunn oscillators are low-noise, low-power sources (local oscillators, speed-detection radar).

IMPATT diode (impact ionisation avalanche transit time). A reverse-biased junction near breakdown. Avalanche current builds up with a delay (about a quarter cycle) behind the RF voltage, and the carriers then take another delay to cross the drift region; the total phase shift near 180° makes the device look like a negative resistance. Frequency \( f \approx v_s/(2W) \) for drift length \( W \). IMPATTs give high power among solid-state sources but are noisy (avalanche multiplication is a random process). TRAPATT is a related, lower-frequency, higher-efficiency mode.

Tunnel (Esaki) diode. Both sides degenerately doped, so the depletion layer is only a few nanometres thick and electrons tunnel across it. As forward bias rises, filled states on one side first line up with empty states on the other (current rises), then pass beyond them into the gap (current falls: NDR), before normal diffusion current takes over. Very fast (tunnelling is not transit-limited), low power, low noise; used in oscillators, amplifiers and fast switches.

graph TD
    A[Negative differential resistance] --> B[Bulk: Gunn diode, intervalley transfer in GaAs or InP]
    A --> C[Junction tunnelling: tunnel diode]
    A --> D[Avalanche plus transit delay: IMPATT, TRAPATT]
    E[Transit time as mechanism, vacuum] --> F[Velocity modulation: klystron, reflex klystron]
    E --> G[Crossed fields: magnetron]
    E --> H[Slow-wave interaction: TWT, backward-wave oscillator]

Control and Detection Devices

DevicePrincipleRole
PIN diodean intrinsic layer between p and n; at RF its resistance is set by the DC forward current (stored charge), because the carrier lifetime is long compared with the RF periodswitches, attenuators, limiters, phase shifters
Varactorreverse-bias junction capacitance \( C \propto (V_{bi} + V_R)^{-1/2} \) (abrupt junction) or \( -1/3 \) power (linearly graded)voltage tuning of oscillators (VCOs), frequency multipliers, parametric amplifiers
Schottky diodemetal–semiconductor junction; majority carriers only, so no minority-carrier storage and very fast recoverymixers, detectors
Step-recovery diodestored charge cut off abruptly, producing a sharp step rich in harmonicsfrequency multipliers, comb generators
Point-contact (crystal) diodemetal whisker on a semiconductor, tiny capacitancehistoric microwave detectors and mixers
Bolometer / thermistor mountabsorbed RF heats a resistive element; resistance change measured in a bridgeabsolute RF power measurement
Thermocouple power sensorRF heats a load; thermocouple reads the temperature risetrue average power, independent of waveform

Diode detectors: square law and linear

A diode’s current near zero bias is \( I = I_s(e^{V/V_T} - 1) \approx I_s\left(\frac{V}{V_T} + \frac{V^2}{2V_T^2} + \cdots\right) \). For a small RF voltage \( v\cos\omega t \), the linear term averages to zero and the quadratic term leaves a DC component proportional to \( v^2 \), i.e. to the RF power. This is the square-law region, used for power measurement at low levels. At large signals the diode rectifies the peaks and the output follows the envelope (linear detection), the AM envelope detector. A mixer uses the same nonlinearity on two inputs, \( (v_1\cos\omega_1t + v_2\cos\omega_2t)^2 \), producing \( \omega_1 \pm \omega_2 \): the heterodyne principle behind superheterodyne receivers and spectrum analysers.

Memory Tricks

Don’t Confuse

ThisvsThat
Gunn diode: bulk effect, no junctionIMPATT and tunnel diodes: junction devices
IMPATT: high power, noisyGunn: lower power, cleaner
Two-cavity klystron: amplifierReflex klystron: oscillator
Magnetron: high-power oscillatorTWT: broadband amplifier
Phase velocity in a guide: \( > c \)Group velocity: \( < c \), carries energy
Square-law detection: output \( \propto \) powerLinear (envelope) detection: output \( \propto \) amplitude
PIN diode: RF resistor controlled by DCVaractor: capacitor controlled by reverse bias
\( \lambda/4 \) line inverts impedance\( \lambda/2 \) line repeats it

Common Mistakes

Practice

All questions below are original practice questions written for this page. They are not from any CSIR NET paper.

Level 1: Foundation

  1. What is the VSWR on a line terminated by a short circuit?
  2. Which microwave tube is a broadband amplifier using a helix?
  3. What is the characteristic impedance of a quarter-wave section that matches 50 Ω to 200 Ω?
Answers
  1. Infinite. \( \lvert\Gamma\rvert = 1 \).
  2. The travelling-wave tube.
  3. 100 Ω. \( \sqrt{50 \times 200} \).

Level 2: Part B Style

Practice Q1. A 50 Ω line is terminated in 100 Ω. The fraction of incident power reflected is:

(a) 1/2 (b) 1/3 (c) 1/9 (d) 1/4

Answer: (c) 1/9

\( \Gamma = 50/150 = 1/3 \); reflected power \( \lvert\Gamma\rvert^2 = 1/9 \approx 11\% \). Option (b) is \( \Gamma \) itself.

Practice Q2. A Gunn diode with an active length of 10 µm operates in the transit-time mode with domain velocity \( 10^5 \) m/s. Its oscillation frequency is about:

(a) 1 GHz (b) 5 GHz (c) 10 GHz (d) 100 GHz

Answer: (c) 10 GHz

\( f = v_d/L = 10^5/10^{-5} = 10^{10} \) Hz.

Practice Q3. The cut-off frequency of the dominant mode in a rectangular waveguide with inner dimensions 22.86 mm × 10.16 mm is about:

(a) 6.56 GHz (b) 13.1 GHz (c) 14.8 GHz (d) 3.28 GHz

Answer: (a) 6.56 GHz

TE\( _{10} \): \( f_c = c/2a = 3 \times 10^8/(2 \times 0.02286) = 6.56 \) GHz. (b) is TE\( _{20} \), (c) TE\( _{01} \), (d) uses \( 4a \).

Practice Q4. Which device’s negative resistance arises from intervalley transfer of electrons?

(a) tunnel diode (b) IMPATT diode (c) Gunn diode (d) PIN diode

Answer: (c) Gunn diode

Tunnel diode: band-to-band tunnelling; IMPATT: avalanche plus transit delay; PIN: not an NDR device at all (a controlled RF resistance).

Level 3: Part C Style

Practice Q5. In the X-band guide (\( a = 22.86 \) mm, \( b = 10.16 \) mm), consider operation at 15 GHz and at 10 GHz:

  1. At 15 GHz, exactly three modes (TE\( _{10} \), TE\( _{20} \), TE\( _{01} \)) can propagate.
  2. TM\( _{11} \) propagates at 15 GHz.
  3. At 10 GHz the guide wavelength is about 3.97 cm.
  4. At 10 GHz the product of phase and group velocities equals \( c^2 \), with the group velocity about \( 0.75c \).

Which are correct?

(a) 1 and 3 only (b) 1, 3 and 4 only (c) 2 and 3 only (d) 1, 2, 3 and 4

Answer: (b) 1, 3 and 4 only

Cut-offs: TE\( _{10} \) 6.56, TE\( _{20} \) 13.11, TE\( _{01} \) 14.75, TE\( _{11} \)/TM\( _{11} \) 16.15, TE\( _{30} \) 19.67 GHz.

Statement 1: three cut-offs lie below 15 GHz. True.

Statement 2: TM\( _{11} \) cuts off at 16.15 GHz. False.

Statement 3: \( \lambda_g = 3.00/\sqrt{1 - (6.56/10)^2} = 3.97 \) cm. True.

Statement 4: \( v_g = c\sqrt{1 - 0.430} = 0.755c \), and \( v_pv_g = c^2 \) always for a hollow guide. True.

Practice Q6. A slotted-line measurement on a 50 Ω line with a purely resistive load shows VSWR = 3, with a voltage minimum located at the load. Consider:

  1. \( \lvert\Gamma\rvert = 0.5 \).
  2. The load is 150 Ω.
  3. The load is about 16.7 Ω.
  4. A quarter-wave section of about 28.9 Ω would match the load to the line.

Which are correct?

(a) 1 and 2 only (b) 1, 3 and 4 only (c) 3 and 4 only (d) 1 and 4 only

Answer: (b) 1, 3 and 4 only

Statement 1: \( \lvert\Gamma\rvert = (S - 1)/(S + 1) = 2/4 = 0.5 \). True.

Statements 2 and 3: a minimum at a resistive load means \( Z_L < Z_0 \), so \( Z_L = Z_0/S = 50/3 = 16.7 \) Ω. (150 Ω would put a maximum at the load.) Statement 2 false, 3 true.

Statement 4: \( Z_0' = \sqrt{50 \times 16.7} = 28.9 \) Ω. True.

Practice Q7. Consider these statements about microwave generators and detectors:

  1. In a two-cavity klystron, velocity modulation at the buncher becomes density modulation in the drift space.
  2. A reflex klystron oscillates when the transit time in the repeller space is \( (n + \tfrac{3}{4}) \) RF periods.
  3. A diode detector operated in its square-law region gives a DC output proportional to the RF voltage amplitude.
  4. A magnetron uses crossed electric and magnetic fields and is primarily a high-power oscillator.

Which are correct?

(a) 1, 2 and 4 only (b) 1 and 3 only (c) 2, 3 and 4 only (d) 1, 2, 3 and 4

Answer: (a) 1, 2 and 4 only

Statements 1, 2 and 4 describe the klystron, reflex klystron and magnetron correctly.

Statement 3: square-law means DC output \( \propto v^2 \), i.e. proportional to RF power. Output proportional to amplitude is the large-signal (linear, envelope) regime. False.

Quick Revision Table

ItemResult
Line impedance, speed\( Z_0 = \sqrt{L/C} \), \( v = c/\sqrt{\varepsilon_r} \)
Coax\( Z_0 = (60/\sqrt{\varepsilon_r})\ln(b/a) \)
Reflection\( \Gamma = (Z_L - Z_0)/(Z_L + Z_0) \), reflected power \( \lvert\Gamma\rvert^2 \)
VSWR\( (1 + \lvert\Gamma\rvert)/(1 - \lvert\Gamma\rvert) \); resistive load \( Z_L = SZ_0 \) or \( Z_0/S \)
Quarter-wave\( Z_{\text{in}} = Z_0^2/Z_L \); matching section \( \sqrt{Z_1Z_2} \)
Waveguide cut-off\( (c/2)\sqrt{(m/a)^2 + (n/b)^2} \); TE\( _{10} \): \( c/2a \)
Guide wavelength\( \lambda_0/\sqrt{1 - (f_c/f)^2} \); \( v_pv_g = c^2 \)
Skin depth\( \sqrt{2\rho/\omega\mu} \); Cu: 2 µm at 1 GHz
Transistor limit\( f_T = g_m/2\pi(C_\pi + C_\mu) \); Miller \( C_\mu(1 + \lvert A_v\rvert) \)
Klystronvelocity → density modulation; reflex: transit \( (n + 3/4)T \)
Magnetroncrossed fields, high-power oscillator, ovens at 2.45 GHz
TWThelix slow wave, broadband amplifier
Gunnintervalley transfer (GaAs, InP), bulk NDR, \( f = v_d/L \)
IMPATTavalanche + transit, high power, noisy
Tunnel diodedegenerate doping, tunnelling NDR, fast
PIN / varactor / SchottkyRF switch / tuning / mixer-detector
Diode detectorsquare law (\( \propto \) power) at low level, linear at high

Key Takeaways

What’s Next

Advertisement
Advertisement